To reduce emissions of carbon dioxide (CO2) Carbon Capture and Storage (CCS) technologieshave been developed. Chemical Looping Combustion (CLC) is a CO2 capture technologywith the CCS framework, and at Chalmers University of Technology in Gothenburg,Sweden, a 100 kW chemical looping combustor has been built.This project aimed to investigate to what degree air can replace helium as the uidizinggas for uid dynamical studies in a CLC cold ow model of the above mentioned 100 kWfacility. Experiments were performed using air and helium separately as uidizing gas andpressure data were obtained, which formed the basis for the comparison. The project alsoaimed to investigate uid dynamics in the uidized bed and study when the risk of sluggingoccuring was greatest. The results were presented in the form of figures and tables dividedinto pressure, concentration and standard deviation of the pressure.The results obtained showed that air as uidizing gas did not create the same uid dynamicsas helium over the entire fuel reactor.

Fortum has in a pilot project installed metering equipment with wireless communication in secondary substations in Stockholm. So far, the collected data are used only in specific projects.This master thesis was carried out at Fortum Distribution AB in Stockholm during 2013. The purpose of this study is to simplify and enhance the use of data in for example network planning process, by giving suggestions on how data can be managed and giving examples of analyzes that collected data can be used for.The electricity meter which Fortum has installed is a EDMI-Mk10A which is set to measure max/average/min values with a one hour time resolution of the following parameters: voltage (per phase), current (per phase) andactive power and active and reactive energy.In order to analyze the collected data an analysis tool is required. During this thesis two customized tools in Microsoft Excel have been developed, one for sorting data and one for analyzing.One aim of the thesis is to show examples of what collected measurement data can be used for. This work shows an example of analysis of active power, power factor, voltage, occurrence of interrupts and the relationship between outdoor temperature and power.This master thesis has among others resulted in the following advice: Expand the number of secondary substations with measuring equipment.

To reduce emissions of carbon dioxide (CO2) Carbon Capture and Storage (CCS) technologieshave been developed. Chemical Looping Combustion (CLC) is a CO2 capture technologywith the CCS framework, and at Chalmers University of Technology in Gothenburg,Sweden, a 100 kW chemical looping combustor has been built.This project aimed to investigate to what degree air can replace helium as the uidizinggas for uid dynamical studies in a CLC cold ow model of the above mentioned 100 kWfacility. Experiments were performed using air and helium separately as uidizing gas andpressure data were obtained, which formed the basis for the comparison. The project alsoaimed to investigate uid dynamics in the uidized bed and study when the risk of sluggingoccuring was greatest. The results were presented in the form of figures and tables dividedinto pressure, concentration and standard deviation of the pressure.The results obtained showed that air as uidizing gas did not create the same uid dynamicsas helium over the entire fuel reactor.

The primary function of a mixer is to keep a fluid in constant motion. All mixing applicationsrequire varying degrees of small-scale turbulence and bulk flow. The performance of asubmersible mixer is measured by the thrust that it produces, while the strength of the bulkflow is dependent on the total amount of installed thrust.In a mixer, the fluid quickly flows past the propeller, and as a result, the current is mainlyaxial. The fluid will also obtain a rotating velocity, or a swirl, though this is significantly lessthan that of the propeller. During the process, the total amount of energy increases in the formof static pressure and kinetic energy.

The horse has been domesticated for several thousand years. It has gone from being used primarily for food and transportation, to become one of the most popular pets in Sweden. With over 150,000 practitioners, horseback riding is one of the biggest sports in Sweden and there is a variety of specializations to choose from. One orientation is western riding which is a broad sport with several disciplines where most originate in cattle work and other ranch tasks. Western riding is a growing sport in Sweden with an increasing number of practitioners and with many different organizations and associations, it is important that the correct knowledge of the equipment used is disseminated. Artificial aids are available in a variety of designs and the most common variants used by western riders in Sweden is draw reins or some forms of martingale.

The purpose of this thesis is to examine how investments are justified in the Swedish data center industry, with a focus on cooling equipment. This is achieved through semi-structured interviews with 20 different interviewees. These interviewees represent different facets of the industry and facilitate an understanding of which factors, such as: investment costs, operating costs, reliability, environmental impact and the influence of external and internal actors, come into play and to which degree they impact the investment decision-making process. The results show that primarily low operating cost in the form of low energy consumption is the driving factor when it comes to the procurement of new equipment. A lower environmental impact is a positive side-effect of lower energy consumption.

The Master Thesis work this report is based upon has been conducted in cooperation with Svea Teknik AB. Svea Teknik is a consultant firm which is developing parts of a tunnel boring machine on behalf of Atlas Copco. The machine is being developed to mechanically excavate hard rock by fixating itself in the tunnel and then press a large rotating cutter-wheel equipped with disc-cutters against the tunnel wall. The disc-cutters are the tools that are in direct contact with the hard rock and are therefore exposed to extensive wear and needs to be replaced on a regular basis.The purpose of this Master Thesis has been to develop a service equipment that will enable time effective and safe changes of disc-cutters. The disc-cutters have a diameter of 17 inches and weigh about 130 kg.

To reduce emissions of carbon dioxide (CO2) Carbon Capture and Storage (CCS) technologieshave been developed. Chemical Looping Combustion (CLC) is a CO2 capture technologywith the CCS framework, and at Chalmers University of Technology in Gothenburg,Sweden, a 100 kW chemical looping combustor has been built.This project aimed to investigate to what degree air can replace helium as the uidizinggas for uid dynamical studies in a CLC cold ow model of the above mentioned 100 kWfacility. Experiments were performed using air and helium separately as uidizing gas andpressure data were obtained, which formed the basis for the comparison. The project alsoaimed to investigate uid dynamics in the uidized bed and study when the risk of sluggingoccuring was greatest. The results were presented in the form of figures and tables dividedinto pressure, concentration and standard deviation of the pressure.The results obtained showed that air as uidizing gas did not create the same uid dynamicsas helium over the entire fuel reactor.

Syntesdesign AB is an academic company that is supposed to enter the HIV drugmarket by manufacturing a "me-too"-drug with indinavir as the starting substance.Our task is to find 100 potential indinaviranalogues. Our further task is to suggesthow to perform a bondingassay to test the affinity for all these analogues. We willpresent a method, required equipment and calculated costs for the assay..

This study has been carried out in the spring of 2014 on behalf of PQR Consult AB in Stockholm. The aim of the study has been to analyse the energy usage of the building Skarpövägen 1 in order to explore the possibilites of saving energy by using appropriate equipment. These possible solutions have been simulated by using the programe IDA Indoor Climate and Energy, combined with a life cycle cost analysis. The laundry building, Skarövägen 23, has also been analysed due to its high amount of energy usage. The result of the energy analysis showed that the energy usage was much higher than the energy declaration.

Habia Teknofluor AB makes parts of PTFE. With their process they reaches a pressure of 250bar at maximum. For their parts to improve they need to reach 400bar at least. We will give suggestions that can solve their problem. All our suggestions is described in the report with a conclusion.

The aim of this study was to investigate the intraoperative surgical stress response in dogs undergoing ovariohysterectomy and to compare acepromazine and medetomidine as premedications. 15 dogs diagnosed with pyometra were used in this study. Blood pressure and heart rate were used as parameters to measure surgical stress response. The surgery was divided into four phases. Phase 0 was the period 10 minutes before the skin incision, phase 1 was skin incision and opening of abdomen, phase 2 was manipulation of uterine horns, ligation and transection of mesovarium and phase 3 was ligation of cervix, removal of organs and closing the abdomen. The results showed that phase 2 was the most intense phase of surgical stress, regardless of which premedication the dogs received. When acepromazine and medetomidine were compared the results showed that within phase 3, all dogs that were given medetomidine had higher blood pressure compared to dogs that were given acepromazine. The dogs that were given acepromazine had higher heart rate than the dogs that were given medetomidine in phase 0, phase 2 and phase 3. .

To reduce emissions of carbon dioxide (CO2) Carbon Capture and Storage (CCS) technologieshave been developed. Chemical Looping Combustion (CLC) is a CO2 capture technologywith the CCS framework, and at Chalmers University of Technology in Gothenburg,Sweden, a 100 kW chemical looping combustor has been built.This project aimed to investigate to what degree air can replace helium as the uidizinggas for uid dynamical studies in a CLC cold ow model of the above mentioned 100 kWfacility. Experiments were performed using air and helium separately as uidizing gas andpressure data were obtained, which formed the basis for the comparison. The project alsoaimed to investigate uid dynamics in the uidized bed and study when the risk of sluggingoccuring was greatest. The results were presented in the form of figures and tables dividedinto pressure, concentration and standard deviation of the pressure.The results obtained showed that air as uidizing gas did not create the same uid dynamicsas helium over the entire fuel reactor.

Increased understanding of the mechanisms that operate in conjunction with the welding of metal surfaces may help to improve existing manufacturing processes, and to enable new products and combinations of materials. The purpose of the project has therefore been to acquire a deeper understanding of what is happening in the bond for steel and for the factors that form the basis for a bond to develop between metals in the production of laminates by pressing. The merge has been done by pressing and the surfaces after the experiments have been studied in detail in the scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX) and with interferenceprofilometry in Wyko, to provide a greater understanding of the mechanisms that influence the bonding in the interface between metals. The project was limited to contain the materials Docol 1000, HyTens 1200, Aluminum AA3003 and a commercial steel. The parameters varied in the experiments to study their influence closer are temperature, pressure, heat treatment and pretreatment. This has been implemented by pressing with varying temperature and pressure.

The purpose of this work is to find out if the suctionvalve to the salivaejector for dental equipment in a simple way can be improved or if a new design is needed. The result of the examination of the suctionvalve shows that the friction between the piston and the seal is high and that this causes the valve in a few cases sheaves. The study concluded that only small changes in material or detail, improve the component..