Orust Kretsloppsakademi is a nonprofit organisation, with a goal of annually generate the same amount of electrical energy that is consumed. Orust is an island on the west coast of Sweden, north of Gothenburg. The population of 15 000 reaches 40 000 during summer, due to the large amount of vacationer. The total electricity demand is 174 GWh a year with a maximum power need of 32 MW. This report presents an analysis for the plausibility of their plan and from a power system stability perspective, the effects on the electrical grid.The conclusion is that the restraints for development of power generation from wind, solar and wave generation, are the power systems capability to transfer power, primarily in the transformers of the grid.

The technological legacy from the early electrification of the Swedish railroads has resulted in a power grid with a lower grid frequency than the national power grid from which it is fed. Energy transfer between these power grids with different frequencies requires substations, adapting the grid frequency for the rail road power grid. For this purpose, a feeding power grid has been built, stretching across the country from Boden in the north to Tälle/Häggvik in the south.Power transfer in the Swedish power grid results in voltage angle differences which increase with increasing loads and transfer distance. These voltage angle differences are transferred from the power feeding substations to the rail road power grid, will in some extent cause loss of energy due to unwanted power flows from north to south.To minimize the losses due to this phenomenon, a power management system called EFS 132 kV has been developed and implemented. The system minimizes the unwanted power flows and controls the desired power flow for a good distribution of loads between the power feeding substations.This thesis investigates the extent of the transmission losses avoided due to the EFS 132 kV that coordinates the idling angles to a common reference point.The results indicate that EFS 132 kV affects the power flow, especially between the northern substations through an improved load distribution.

A piezoelectric injector was modeled, in this Master Thesis Project which was carried out at Scania CV AB in Södertälje, in GT-Fuel. GT-Fuel is simulation program from Gamma Technology.The simulation model for the piezo injector was divided into a hydro-mechanical system and an electrical system (Piezoelectric element). First the hydro-mechanic model was duplicated from Advance Continuous Simulation Language model (ACSL). The simulation results were then compared to the ACSL, to verify that the hydro-mechanical system was modeled correctly. The simulation results for the electrical model were also compared with a Simulink model.

Examensarbetet syftar till att jämföra nya alternativ till olika system för användning i laborationer i reglerteknikkurser för olika studentkategorier. Det skall utredas vilket av ett antal alternativ till mjukvaruplattformar som är bäst lämpat att användas vid reglerteknikundervisningen i ITN:s reglerlaboratorium vid Linköpings universitet. Tidigare laborationer i berörda kurser skall även modifieras så att dessa kan genomföras i de nya systemen.Examensarbetet resulterade i en rad modifierade laborationer och system att tillämpa i dessa. De nya systemen medför att all reglering sköts direkt från en dator istället för tidigare variant med externa apparater som programmeras. På så sätt kan större fokus läggas på regleringen i sig och inte de system som tillämpas för att utföra den..

Modelica is a multi-domain and equation-based modeling language. Modelica is based on object-oriented principles and non-causal modeling. The language is constructed to facilitate reuse and decompose models. The models and the modellibrary can modified to design a new nonlinear components.Object-oriented modeling is an excellent way to analyze and study large complex heterogeneous physical systems. The object-oriented modeling approach build on reusing and decomposition of models and non-causal modeling.Modeling physical systems often leads to a DAE system with index 2 or 3.

This master thesis describes the development of an UPS module. UPS is an acronym for Uninterruptable Power Supply. The UPS module has been developed at the company AerotechTelub AB. The UPS module delivers the necessary voltage and current in case of a power interrupt. If a power interrupt occur, the computer system has one to three minutes available to store data and shut down correctly.

This paper describes the development of a simulation model for the ambulance flow in the Västra Götalands-region of Sweden, and an analysis tool for the output of the simulation model. The aim of the simulation model was to be able to evaluate the outcome from changes in the ambulance operations, such as a reorganization of ambulances or an increase in intensity of the ambulance calls. This evaluation is meant to serve as decision support for the strategic planning of the ambulance operations. The analysis tool was developed to visualize the abundant geographical data produced by the simulation model in a meaningful way. The simulation model was validated against historical data which showed that the dispatch time for the highest prioritized ambulance calls corresponds well with historical data.

In this final thesis two simulation models have been integrated. The simulation models are models of JAS 39 Gripen?s fuel system, software and hardware. The time consuming and costly work to develop software has made the department of fuel system to build two models in Xmath/Systembuild. The software model also simplifies the comprehension of how the software in the control computer of the fuel system works.

ABB is one of the world?s leading engineering companies in power and automation technologiesand their solutions improve performance while lowering environmental impacts for energycompanies and industries. ABB FACTS designs equipment and plants for series and phasecompensation.This thesis has been performed at ABB FACTS on the Mechanical Design (DM) department inVästerås, Sweden. The purpose of the thesis was to develop and design calculations andsimulation tools for ABB FACTS?s standard series capacitor platforms.

A large amount of our time is spent indoors in an artificial climate. To make the experience pleasant there are requirements on the ventilation and the heating system. At the present time the most common form of heating is a radiator system complemented with a ventilation system. A ceiling heating system with combined heating and ventilation can replace the two separated systems. The benefit with a ceiling heating solution is that it saves space since the radiator system is no longer needed.

A Monte Carlo simulation of the ELECTRA reactor using (U,Zr)N fuel and a liquid lithium coolant is performed using the Serpent simulation code. The results show a reactor with a total reactivity coefficient of the coolant, fuel and material expansion that is strongly negative. These properties make the ELECTRA reactor a good candidate for a safe space reactor that could be used for propulsion of manned and unmanned space vehicles to Mars and other parts of our solar system..

Ocean Thermal Energy Conversion, OTEC, is a sustainable energy conversion technology that is not yet commercialized. OTEC is a technology that utilizes the temperature difference in oceans between the warm surface water and the cold water at 1 000 m depth to run a Rankine Cycle. This technology can produce electricity and provide synergies like fresh water, air conditioning and aquaculture. A simulation program for three alternative OTEC systems has been created in order to decide which OTEC system is most profitable; closed, open or hybrid system. In this simulation a production cost analysis is performed in order to investigate and decide which one of the three systems that has the lowest production cost. The production cost analysis also analyzes if the profitability is affected by the size of the facility. After these analyzes, the most profitable of the three different OTEC-systems is expanded by an installation of solar collectors in order to see if the thermal efficiency is improved. The result shows that the most profitable system varies with the size of the facility.

This thesis work contains a litterature study about electrical motors in general and how PWM-patterns for brushless DC-motors can be made. A suitable method has been implemented as a simulation model in VHDL. A simulation model of a brushless DC-motor which describes the phasecurrents, torque and angular velocity has also been made. The motor model made simulations easier for the complete PWM-system. The design was synthesised and tested with a prototypeboard including a SPARTAN II FPGA.

In this project a simulator has been developed (in C++) with the purpose of illustrating how changes in environmental regulations, tax levels and other policy measures affect the composition of an energy system. The aim of the project was to investigate how energy companies? investment strategies are affected when changes in economic and environmental conditions occur. A standard scenario has been created based on current Swedish conditions, but the user can create new scenarios and set parameters freely. The user is tasked with building power plants to supply the city/region with district heating and electricity during a pre-set number of years. When the simulation is finished the result is graded in the following categories: economy, environment and quality. To evaluate the simulator three scenarios were created (?early 20th century?, ?reduced environmental control? and ?future?) in addition to the standard scenario and these were compared with each other by examining how a select group of power plants perform under the given conditions.

Linux is a growing operating system in embedded systems. Today, Linux is not only in heavy servers but also in cell phones, PDAs, cameras and other devices running on battery power. While current technology is more energy efficient, more and more technologies are implemented into a single unit resulting in an overall increase of power consumption.Low power consumption is an increasingly important feature of a system today. Lower power consumption means lower costs, less environmental impact, and longer life for applications that runs on batteries.This work compiles methods to reduce power consumption of Linux systems. The work includes examining whether the available opportunities are platform-specific or of a more general nature.