The aim of this project was to look into ten small sewer systems in the municipality of Laholm, in Sweden, in order to work out common assessment grounds for them. The sizes of the systems for purification of wastewater were within the range of 25 to 2000 population equivalents. Our method was to study literature, the laws and regulations applicable and the files at the municipality. The conclusion is that every sewer system is different and every situation is unique. We concluded that based on laws and assessment grounds sewer systems equal in size and Pollution load ought to have similar demands attached to them.

The report is part of the university´engineer program within Industrial Organization and Economics with specialization in Logistics and Managment at Jönköping´s university.Skoghall´s mill underlies a large supply chain, which means there should be a lot of areas in need of small improvement measures. This report illustrates a small part of one of these areas and is focused on the loading distribution services in the terminal Vänern.At the moment there´s a very unequal load of the load carriers SECU box and Container at the terminal. Skoghall´s mill has the desire to equalize the high and low load levels of the 2 loading carriers named previously. One of the options to solve the problem is to set a limit of how much the carriers can load per week or per day. The mill also wants it to be investigated if the proposition would influence the customers in any way and if both the company and its customers could handle a lower level of delivery services in case the proposition was to be applied.The goal to be achieved with this thesis is to provide balance to the unequall loading of the 2 load carriers, SECU and Container, and investigate whether or not the Skoghall´s mill´s customers, could manage the lower degree of delivery service that the proposition would imply.For this goal to be achieved, random sample investigations were taken from orders of a customer that is provided with SECU load carriers and the same was made with a Container´s customer.

The goal with this examination thesis is to investigate the difference in carbon dioxide emissions between a building with a wooden versus concrete carcassing from a life cycle perspective. The huge amounts of carbon dioxide released into air from human activities must be reduced to prevent serious consequences. A way to limit this issue is through performing a comparative study where the result shows which of two products with the same function has the lowest emission of carbon dioxide, whereof the product with the lowest carbon dioxide pollution can be chosen.To be able to perform a study like this an object has been chosen and studies about life cycle analyses have been done. The rental square meter, the thermal conductivity value, the energy requirements and the placement of the building has been set equal in both framework types. There were solely dissimilarities of the two buildings taken into account when this comparison study was performed.The result of the study is that a building constructed with a wooden carcassing has the lowest amount of carbon dioxide emissions.

This master thesis deals with steel girders subjected to patch loading caused by concentrated moments. There exist no good methods to calculate by hand the ultimate resistance for this load case. In ?tunnplåtshandboken?, (Handbook for sheet metal, which is published by SSAB), one calculation method is presented. It?s however fairly difficult to use, because of many calculation steps and many graphs.

The power consumption has grown rapidlyin the last decade. Fossil fuels and theneed for alternative energy sources aregreat. Ocean waves are a renewable andsustainable source of energy that hasbeen relatively untapped. At UppsalaUniversity research and development havebeen done for several years. Severaltypes of wave energy converters (WEC)have been created.

A method for measuring the total impulse from a multi hole diesel injector, introduced inprevious thesis work, ?Development of a method and a device for measuring the momentumrate of fuel sprays?, by Mikael Lindström, has been further developed and tested. The conceptis to simultaneously deflect all sprays from a multi hole diesel injector by using a bell shapeddeflector. The fuel sprays are deflected straight down from their initial umbrella angle, andthe resulting deflection force is measured in a thin strained section of the load cell. The strainis given by three strain gauges, with quarter-bridge circuitry for each gauge.

The Kedertruss is the loadbearing part in the Keder weatherprotectionsystem and it has been analyzed concerning its loadbearing capacity. The Kedertruss is produced and manufactured by Wilhelm Layher GmbH & Co. KG and this report has been made for their Swedish division Layher AB.  The Kedertruss, designed in Germany according to German designcode, has been recalculated concerning Swedish conditions according to Eurocodes and a ongoing European standardization project. The two-dimensional program Winstatik Frame Analysis has been used for evaluation of load effects. Capacity has been calculated by hand-calculations and it has been verified that the Kedertruss in its larger spans isn?t able to withstand the loads.

The main purpose of this study is to clarify the underlying reasons as to why people choose to travel by car or taxi, and to do so by using people´s choice of transportation to and from Arlanda Airport as an example. Furthermore it is also in our interest to see what changes are needed to make more travellers use the available public transportation.Because of the increasing pollution rate from the means of conveyance headed to and from Arlanda Airport, Luftfartsverket is attempting to decrease the amount of emission from the connecting transportation sources. Luftfartsverket has a pollution limit which is about to be reached in a few years, based on a prognosis made by Arlanda´s office of environmental issues. In order to investigate people´s travel mode choice a survey was conducted at Arlanda Airport, Stockholm. 82 travellers were interviewed on a three day basis inside terminal 4 and 5.

This Master?s Thesis aims to illustrate in what ways the two Swedish environmental assessment tools, the Environmental Load Profile and EcoEffect differ and if performed valuations gives different results and environmental goals.The built urban environment causes about half the environmental loading in Sweden. The society?s ambition towards sustainable development has resulted in demands reducing the environmental load. One way to accomplish this change is with the assistance of tools for environmental assessment of the built environment.

Studies have shown that air pollution, as well as bark fissure depth and sun exposure of a tree can have an effect on lichen growth as well as abundance of lichen species. The aim of this study was to find out the relative importance of these factors. 211 oaks in south eastern Sweden were surveyed for presence of 17 lichen species, as well as the total number of lichen species. Half of the trees were situated in urban areas and half in the countryside. For each tree the bark fissure depth was measured and the sun exposure of the trunk was estimated.

The Kedertruss is the loadbearing part in the Keder weatherprotectionsystem and it has been analyzed concerning its loadbearing capacity. The Kedertruss is produced and manufactured by Wilhelm Layher GmbH & Co. KG and this report has been made for their Swedish division Layher AB.  The Kedertruss, designed in Germany according to German designcode, has been recalculated concerning Swedish conditions according to Eurocodes and a ongoing European standardization project. The two-dimensional program Winstatik Frame Analysis has been used for evaluation of load effects. Capacity has been calculated by hand-calculations and it has been verified that the Kedertruss in its larger spans isn?t able to withstand the loads.

The construction of buildings and paved surfaces changes the natural water balance.Precipitation generates surface runoff and storm water instead of infiltrating into the soil.Storm water has come to be considered as a major source of pollution in lakes and streams inthe vicinity of urban areas. Reduction of pollutants in storm water is a key action in order toprotect sensitive recipients and maintain high water quality. Storm water is traditionallytransported by storm sewers to the nearest recipient. In recent years the approach to stormwater management has changed; storm water should primarily be disposed of on site, throughlocal disposal of storm water, LOD. LOD is created by a combination of the function ofseveral smaller local facilities and the general sewer system.

Combustion of fossil fuels is today the dominating source of energy. During combustion,carbon dioxide is formed. The carbon dioxide accumulates in the atmosphere,which raises the global average temperature on earth through the so called greenhouseeffect. The only way to reduce the emissions of carbon dioxide from combustionin a coal fired power plant is through carbon capture and storage (CCS).Post-combustion capture is a technology to separate carbon dioxide from the uegas after the combustion for efficient transport and storage. The steady state operationof coal fired power plants with post combustion capture has already beenthoroughly investigated on a pilot scale, however much work remains to investigatethe plants dynamic operation.

The Kedertruss is the loadbearing part in the Keder weatherprotectionsystem and it has been analyzed concerning its loadbearing capacity. The Kedertruss is produced and manufactured by Wilhelm Layher GmbH & Co. KG and this report has been made for their Swedish division Layher AB.  The Kedertruss, designed in Germany according to German designcode, has been recalculated concerning Swedish conditions according to Eurocodes and a ongoing European standardization project. The two-dimensional program Winstatik Frame Analysis has been used for evaluation of load effects. Capacity has been calculated by hand-calculations and it has been verified that the Kedertruss in its larger spans isn?t able to withstand the loads.

Tomo Hugglink (TOMO Skog) is an innovation for harvest and transport of biofuels. The system consists of a truck, a chipping unit and crane mounted on a link and a wood chip trailer. The system works in such a way that the chipping unit is disconnected and placed on the site and wood chips are loaded directly into the wood chip trailer.The aim of this study was:- To examine the performance of the TOMO Hugglink system under different conditions such as the size, placement and quality of the pile.- To calculate the cost per raw ton for two vehicle combinations at different transport distances and to examine the effect of a reduction in set-up time and an increase in load weight.- To identify possible improvements with the TOMO Hugglink system.A time study was conducted within the thesis work to make it possible to determine production and time consumption. In the subsequent economic analysis the cost per tone at different transport distances was calculated for two different lorry concepts. Furthermore the effect of a reduction in set-up time and an increase in load weight was calculated.Under current conditions the utilization of the chipper is low and only 29 % of the total system time is occupied by chipping.