This report describes the planning and the accomplishment of the final diploma workat the study program Mechanical Engineering, Department of Engineering Sciences, Uppsala University. Two students carried out the diploma work at GE HealthcareHusbyborg in Uppsala.The aim of the diploma work was to develop and improve existing processequipment for 11C-radiochemistry in PET. The process equipment was to be dividedinto smaller independent modules to make it more flexible. Part of the existingprocess equipment is an oven that is supposed to perform a specific chemicalreaction. One of the main goals was to study and improve this oven.The work could be divided into three main phases: 1.Present concepts for one module, and interface between different modules.

Small hydropower plants have been an important source for electricity for many years. During the 70?s the general thought was that nuclear was the future. Around 2000 small waterpower plants were shut down. It wasn?t profitable to invest in.

This has been a thesis work for an bachelor degree at Umeå university. The work has been done at LKAB?s facilities in Kiruna and its main purpose has been to investigate and construct some conceptual designs for replacing a screen with magnetic separation in KA3 concentrator plant. First all information available about magnetic separation was gathered and studies of magnetic separation at the sorting plant and studies of the plant KA3 was conducted. Companies that manufacture magnetic separators were contacted.

In this report focus is put on the combustion process at a cement plant. Combustion is the heart of the cement making process and absolutely crucial to have under full control and well optimized. The fuel is put into the process through a burner pipe and this burner pipe is modified to reach a more efficient combustion. The primary target is to enable burning of heterogeneous alternative fuels and increase the production level. Other positive effects from this type of optimization is lowered specific fuel consumption and lowered CO2 emissions. A redundant burner is chosen for the project and overall the project steps are the following: 1. Installing a Jet air nozzle ring in a way so it can move both axially and radially due to temperature changes. 2.

The aim with this work has been to examine the climate changes and what these has meant, and will mean during the present century, for plants that have not been hardy in Sweden. A lot of new species can probably be grown today in Sweden's most southern parts, due to an increase in the average annual temperature by 1?C. There is a need of information about these new species and their hardiness. The insufficient information about the subject has been the background to this work.

This is a report written for an examination project C-level, on the subject of energy. The examination project is a product of the FVB Sweden AB (district heating bureau). It started with a meeting with Stefan Jonsson FVB Sweden AB, were he explained the content of the project, and from this a presentation of the problem was made. The problem that needed to be solved was how they could control the valves in the system to provide heating to everyone in the system. The valves are often oversized so the pump in the heating plant would have to be enormous to be able to provide enough flow to be sufficient, if everyone in the system had there valves fully opened. I came up with two solutions to the problem, one was a wireless network that could keep track of the valves and the other solution was an extra sensor that was placed on the radiator.

To be a part of the future we have to make a profit, one way to improve the profit margin is by reducing the fixed costs. This paper discusses the financial results of equipment cooperatives in crop production. Through a case study of three farms in Södermanland, we have an example of how it can look today and how it could look tomorrow. The three farms are crop-producing farms with slightly different orientation. Jursta Gård, 155 hectares, and Djursnäs Säteri, 215 hectares, have grains crop and oilseed crops as the main crops, and Nibble Gård, 340 hectares, mostly have pasturelands and some grain crops.

The project has been done in cooperation with Schenker Åkeri AB in Sweden, Halmstad. Theproject is based on an inspection made by Arbetsmiljöverket, where they found minorshortcomings with distribution of goods for the employees. The project is an investigation ofthe drivers? working environment.Schenker Logistics is one of the world's leading providers of integrated logistics services.Schenker Åkeri AB is a subsidiary to Schenker Logistics and transports 2.4 million tons ofgoods yearly.The project started with a background study to evaluate drivers working environment. Wehave studied goods receptions, the working environment, strain injury and injury mechanisms.Methods used was observations, tests, questionnaire surveys and ergonomic andbiomechanical calculations.One result of the study is a working model, which gives recommendations for the maximumweight a driver should push and pull.

Volvo Construction Equipment AB Component Division (CMP) I Eskilstuna har idag det globala ansvaret för utveckling och tillverkning av drivlinor till anläggningsmaskiner. De nya kraven på nästa generations transmissioner har dock krav på sig att vara mindre och lättare samt ha mindre inre förluster än den föregående. För att kunna möta detta krav krävs det att kopplingsaxlarna i tranmissionerna blir mindre. För att leva upp till detta samt en förbättring hos kvalitén på förbanden så introduceras två nya fogningsmetoder enligt laser- och lim/krympförband. I denna rapport klargörs flödet genom de två fogningscellerna.

The study took place at a food corporation in Växjö, Sweden. It describes a building that contains four tanks in which glucose syrup is stored. The purpose of the study was to calculate the amount of heat that leaves the building and the amount of heat that is supplied by the installed heating equipment. Before the calculations could be implemented, all the systems that supply the building with heat had to be examined. With a small amount of information from earlier studies, the work to gather all the data necessary for the calculations began.

As the final course in the education ?University Diploma Programme for Process Operators? there is a thesis in cooperation with a company required.This thesis is about operator maintenance and 5S made at Metsä Board in Husum.In this report you can read my opinions and conclusions based on literature studies and the interviews that have been made with the staff at PM6 (the paper machine).I chose to focus on the theory of lean, 5S and operator maintenance because it covers the area of this thesis.The operators shall do their rounds to make sure that the equipment works fine. They shall also write down things that they notice in a checklist. This is not done as it should be and the question is: can this be solved by using 5S?My conclusion of this thesis are:Better review of the task so that everyone is involved.

This thesis work was made for Södra Cell Mörrums bruk in Blekinge. The purpose of the work was to develop a computer model in the simulation program Extend for the removal and balance of organic oxygen consuming substances, measured as COD (Chemical Oxygen Demand), in the new biological treatment plant in the mill. The plant produces two different pulp products, TCF- (Totally Chlorine Free) pulp and ECF- (Elementary Chlorine Free) pulp, for sale. The different bleaching procedures affect the characteristic of the wastewater and thus the effectiveness of the biological treatment plant.In the model that was developed the COD in the wastewater was divided into five different COD-fractions: soluble easily degradable (SS), soluble hardly degradable (SR), soluble inert (SI), particulate inert (XI) and particulate biomass (XB). To create the model FlowMac? was used as a base.

This degree project is an investigation of solar cells and their ability to deliver electric power as well as reducing the need for cooling. The main object of interest is a BASE-X shelter. The shelter is purchased by the Swedish Defence Materiel Administration, FMV to be used for command and camp in the new force called Nordic Battlegroup, NBG. The demand on the equipment is firstly that it should have a small weight to be easy to transport and handle and secondly to be easy to bring up fast. Therefore the choice of solar cell technology fell on thin film cells.

The project, Glowtest Fixture, has been carried out to and in collaboration with MSA SordinLtd. MSA Sordin Ltd produces and sells ear protector and is at present a supplier on theworld market. Glowtest Fixture is a product for glow testing off detailed components in oneear protector. MSA Sordin Ltd sends today away your products for testing what is anexpensive aspect in their development. The project's aim is to take forward a test equipmentthat copes with those high nonplussed requirements and wishes that are required for anapproved physical execution.Glowtest Fixture is a physical equipment that comes used stem glow physical off all detailedcomponents in one ear protector.

A clean and affordable energy source for cooking is deficient in developing countries. People rely on fuels that contribute to environmental, social and health problems.Biogas is an alternative energy source and an increased investment in small-scale biogas production can in several developing countries be found. Several projects have started to use the technology in developing countries because of the benefits with biogas. Some cases in the establishment of biogas plants have succeeded and some have not. The study is a literature review supplemented by two field studies.