The use of silicon carbide (SiC) as a base material in power electronics has manyadvantages, including high breakdown voltage and excellent temperature endurance.However, the packaging of such electronics presents major challenges and there is aneed for packaging that can operate in higher temperature. The purpose of this thesishas been to develop a test method and verify the functionality of SiC powertransistors prototypes with a new packaging technique developed by Swerea IVF AB.It includes setting up an electrical test-bed for power and high temperature cyclingand analysis of the results. Even though test confirmed functionality after thepackaging process, (at room temperature) the performance seemed to have been reduced. This could be a result of the measurement setup and the packaging process.In higher temperature the transistors failed to operate longer than a couple ofminutes which showed the weaknesses in the design and the challenges with this typeof packaging..

This reports goal is the give BSR AB more information that's useful towards their customers in marketing of their products.It involves tests of different air filters designed for cars and 3D-modelling of Opti-Flow systems. The three models thats being tested is SAAB (93SS), VAG (1.8T) and Volvo (S60). To every brand there are three different models. A orginal- , sport- and an open cone air filter (Opti-Flow).The results indicate that the open Opti-Flow filter has better performance compared to the other cased filters. The sport filters for SAAB and Volvo has better performance then the original filter.

Examensarbetets syfte var att skapa ett generellt mät- och styrsystem som är möjligt att fjärrstyra över Internet. Systemet består av en kontrolldator och ett antal separata moduler, vilka var och en realiserar någon typ av mät- eller styrfunktion. Användningsområdet för ett sådant system är brett; det kan exempelvis användas inom automation av bostäder, för process-övervakning och styrning inom tillverkningsindustrin, eller inom under-hållningsbranschen.Eftersom ett fullt utbyggt system kan bestå av ett drygt 100-tal olika mo-duler, är det här examensarbetet av praktiska skäl begränsat till att rea-lisera en handfull av dessa. Då systemet är enkelt att skala upp, är den be-gränsningen i antalet realiserade moduler i prototypsystemet inget som påverkar de erhållna resultaten. Exempel på storheter som kan övervakas är temperatur, avstånd, lufttryck och ljusstyrka.

The purpose of this paper was, on the basis of the association?s annual reports, to describe appropriate key performance indicators for non-profit associations. The purpose was furthermore to study how the associations show their goal-attainment. The research was delimited to contain the second category of non profit associations, which include sports associations. The authors choose three non profit associations, which according to the law, shall draw up annual reports. The three ice hockey associations HV71, MODO Hockey and Frölunda Hockey Club, were thereafter chosen on the basis of those delimits.

AbstractThis bachelor?s thesis at the Department of Production Engineering at the Royal Institute of Technology in Stockholm deals with the subject of automated metrology. The degree of automation of tasks within production has been a growing trend but the measurement of quality has not followed the same trend. The main thesis follows:What incentives are there to automate the measurement of quality in production?What factors are crucial and why are not all metrology automated?The thesis comes along with a number of sub-queries and delimitations.The working method includes both theoretical and empirical studies.

This Master Thesis has been conducted as an assignment of the Swedish Defence MaterialAdministration and the Swedish Armed Forces and aims to examine the Target Location Error(TLE) of a Forward Observer System. The targeting accuracy of the system is vital if the systemis to be used as a sensor for precision munitions. The analyzed system, EOI (FOI 2000), wasdelivered to the Swedish Armed Forces in 2007. The targeting sequence starts with deciding theposition of the system with a GPS-receiver, continues with methods where the north direction issettled and ends by measuring the distance, direction and elevation to the target. When allparameters have been measured the system calculates the position of the target.

Bakgrund: Cognitive Orientation to daily Occupational Performance (CO-OP) ?r en behandlingsmetod d?r arbetsterapeuten guidar patienten att hitta egna strategier f?r att n? sina m?l. Syfte: Syftet med den h?r intervjustudien ?r att unders?ka arbetsterapeuters erfarenheter av att anv?nda Cognitive Orientation to daily Occupational Performance (CO-OP) som behandlingsmetod f?r vuxna. Metod: Inklusionskriterier f?r urval av deltagare var leg. arbetsterapeuter med erfarenhet av att anv?nda behandlingsmetoden CO-OP med vuxna patienter. Datainsamlingen gjordes genom kvalitativa intervjuer, datan bearbetades genom kvalitativ inneh?llsanalys. Resultat: Utifr?n analys av den insamlade informationen fr?n intervjuer framkom fyra kategorier och nio underkategorier.

The task in this thesis is the steering of one of Saab Bofors Dynamics robots using Sliding Mode Control, a method they never used before. The robot constitutes a system which in addition to perturbations and uncertainties due to modeling imprecision, hold the difficulty of being highly time variant. In order to be able to keep required performance with uncertainties and modeling imprecision present, the use of robust control methods like Sliding Mode Control is necessary. SMC is based on the states of the system being forced to stay on or in the direct vicinity of a hyper plane in the state space which is chosen in a way that gives the system dynamics desired properties. Other advantages with sliding mode are reduced order dynamics on the switching surface and total insensitivity to some uncertainties and perturbations.

The viscosity of air buildings is a hot topic within the construction performers, which the industry feel they have too little knowledge about. This study is mainly aimed against air density in apartment buildings and airflow measurement. The study consists of a theoretical reference, educational visit, interviews and a survey conducted among construction workers at Magistratshagen in Linkoping.Earlier requirement in terms of air leakage through the climate screen was removed and today there are only energy requirement for a dwelling in Boverkets Building Regulations. The difference between a passive and a typical air tight construction is that the passive house have a maximum requirement of 0.3 l /s m2 of air leakage through the building climate screen. The requirement imposed on passive houses is to minimize the supply of power and energy for heating the building.Air tight constructions have heavy demands on the performance and accuracy of everyone involved with the project. The client must specify their requirements and also be prepared to pay for any additional costs. The architect and building planners have to design the building with regard to air tightness. Finally, the construction workers are required to do a careful work in order to get all the connections in the building air tight.The study suggests that an air tight building is a closed system where no forced ventilation exists. There are no reasons not to build too tight as long as there is a functioning ventilation. In this study the authors ask themselves how an air tight building changes over time. No theoretical information has been found on these changes, but the respondents assume that air density decreases with time. The deterioration is mainly assumed to be caused by construction materials changes over time. The study shows that construction workers knowledge of air tight construction is mixed, which they themselves admit in the survey..

Performance Management är en process som syftar till att säkerställa att alla inom en organisation arbetar i samma riktning. Detta uppnås genom att öka tydligheten kring organisationens strategiska mål samt koppla dessa till medarbetarens individuella mål. Vidare är det viktigt att kommunicera vad som förväntas av medarbetarna i termer av arbetsprestationer samt hur detta skall uppnås för att lyckas med uppdraget att minska gapet mellan medarbetares arbetsprestationer och ledningens ambitioner (Armstrong & Baron, 2005).Uppsatsens övergripande syfte är att undersöka vilka erfarenheter ledare inom det multinationella telekom- och IT-företaget Logica har av att arbeta med Performance Management samt vilka delar av implementeringen som har varit lätta respektive svåra att genomföra. Vidare vill jag undersöka hur organisationen ytterligare kan förstärka arbetet med Performance Management-processen baserat på ovanstående.Den empiriska undersökningen har genomförts med kvalitativ metod i form av tre stycken fokusgruppintervjuer med ansatsen Experiential Focus Group. Som komplement till fokusgruppintervjuerna har analys av interna dokument som beskriver Performance Management-processen inom Logica, genomförts.Resultatet av undersökningen visar att ledarnas upplevelser av Performance Management-processen varierar beroende på vilken typ av arbetsgrupp man är ledare för.

ObjectiveThe objective of this study was to investigate the clinical application to use ASSR in anesthetized childrenDesignOne main ambition of the investigation was to compare hearing threshold using ABR with estimated hearing threshold using ASSR. Another aim was to examine if the duration of an ASSR measurement could be reduced by only using the frequencies 1, 2 and 4 kHz and exclude the frequency 0.5 kHz. This is a retrospective study using electrophysiological measurement from a database.ResultResults showed a high correlation between hearing threshold using ABR and estimated thresholds using ASSR, with the frequency 0.5 kHz showing a slightly lower correlation. Result also showed that the test duration was increased when using all test frequencies in ASSR-measurement compared to when 0.5kHz was excluded. ConclusionThe study showed a high correlation when comparing hearing threshold using ABR and ASSR.

AimThe purpose of the study was to investigate how upper secondary school students experience performance demands during their physical education and health classes (PE-classes). The questions were as following: Are there differing perceptions between the sexes whether students experience performance demands? In what situations do the students feel that the demands on their performance are high during PE-classes? Do the students experience of demands on performance differ whether the physical education and health teacher is male or female? Do students feel unfairly treated by the physical education and health teacher during PE-classes?MethodSeven upper secondary schools in Stockholm?s administrative district were randomly selected to participate in the survey. The principals were contacted for further information and to set a date for performing the survey. The project leaders were present during the days the surveys were taken by students in the social science and natural science programs.

A piezoelectric injector was modeled, in this Master Thesis Project which was carried out at Scania CV AB in Södertälje, in GT-Fuel. GT-Fuel is simulation program from Gamma Technology.The simulation model for the piezo injector was divided into a hydro-mechanical system and an electrical system (Piezoelectric element). First the hydro-mechanic model was duplicated from Advance Continuous Simulation Language model (ACSL). The simulation results were then compared to the ACSL, to verify that the hydro-mechanical system was modeled correctly. The simulation results for the electrical model were also compared with a Simulink model.

The Swedish government have a goal that wind turbines shall produce 30 TWh by the year 2020, compared to about 3,5 TWh produced in Sweden during 2010. To minimize the disturbance that wind turbines create the Swedish Environmental Protection Agency has stated a guideline value that noise from wind turbines at nearby residents shouldn?t exceed 40 dBA, at 8 m/s wind speed. With advanced calculation models, like Nord 2000, the emitted sound from future wind turbines can be calculated at an early stage to optimize the power production without exceeding the 40 dBA. When the turbines have been built there is a need to verify that they really are within the guideline.

The rising demand for electricity and heat raises a big challange for the society and engineers. Many products have been introduced to the market to supply more energy to the energy systems. Absolicon AB is a Swedish company that develops and markets a combined heat and power generating product. The product, Absolicon X10, uses a parabolic trough to concentrate the radiation of the sun onto a receiver. The receiveris equipped with mono crystalline solar cells and is cooled by a circulating liquid media.