The Kedertruss is the loadbearing part in the Keder weatherprotectionsystem and it has been analyzed concerning its loadbearing capacity. The Kedertruss is produced and manufactured by Wilhelm Layher GmbH & Co. KG and this report has been made for their Swedish division Layher AB.  The Kedertruss, designed in Germany according to German designcode, has been recalculated concerning Swedish conditions according to Eurocodes and a ongoing European standardization project. The two-dimensional program Winstatik Frame Analysis has been used for evaluation of load effects. Capacity has been calculated by hand-calculations and it has been verified that the Kedertruss in its larger spans isn?t able to withstand the loads.

Tomo Hugglink (TOMO Skog) is an innovation for harvest and transport of biofuels. The system consists of a truck, a chipping unit and crane mounted on a link and a wood chip trailer. The system works in such a way that the chipping unit is disconnected and placed on the site and wood chips are loaded directly into the wood chip trailer.The aim of this study was:- To examine the performance of the TOMO Hugglink system under different conditions such as the size, placement and quality of the pile.- To calculate the cost per raw ton for two vehicle combinations at different transport distances and to examine the effect of a reduction in set-up time and an increase in load weight.- To identify possible improvements with the TOMO Hugglink system.A time study was conducted within the thesis work to make it possible to determine production and time consumption. In the subsequent economic analysis the cost per tone at different transport distances was calculated for two different lorry concepts. Furthermore the effect of a reduction in set-up time and an increase in load weight was calculated.Under current conditions the utilization of the chipper is low and only 29 % of the total system time is occupied by chipping.

The Island of Öland has one of the best wind climates for land based wind power in Sweden. An objective for the Island is to become self sufficient using electricity from renewable source of energy such as wind. There is currently 55 MW capacity installed on the Island and it is estimated that grid congestion will occasionally occur if more than 135 MW was installed.The aim of this thesis is to investigate he possibilities for load management by smart charging of electric vehicles, EV. The definition of smart charging is that the charging is done to some extent with an ICT-system, (information and communication technology) that correlates wind electricity generation to the charging of electric vehicles. The purpose is to avoid grid congestions on the sub-sea cable that connects Öland to the mainland because that in turn would curtail wind energy production.

This report summarizes the development of a calculation program estimating the profitability of converting a peak-load oil-fired boiler to pellets. To convert an oil-fired boiler to pellets a new fuel handling system must be designed. Changes also have to be made to some other components. Since there are many different techniques for transportation, storage and treatment of the fuel only the most interesting techniques from Swecos experience and interest were included in the study.The capacity of the different parts in the system was dimensioned based on the power of the boiler after conversion. To estimate prices, installed power and dimensions manufacturers and distributers were contacted.

The constant need of energy is something that affects us all no matter our current situation. Whether we are driving our car to work, taking the elevator or using the oven to cook dinner we end up relying on energy. Our whole society is continuously striving to achieve a higher grade of efficiency and the process of supplying ourselves with energy is no exception. The importance of appliances in our everyday life cannot be exaggerated and thus the importance of their high efficiency.Efficiency is already a keyword in the appliance industry with labels, stars and numbers helping us choosing the most suitable option for the task ahead. No matter how efficient appliances often use pure electricity as their energy source.

Background: Today, the trademark is the heart of the company and the management of brandimage and identity require certain attention and care. In an increasingly tough business climatewhere the brand today has a central and important role, it is understandable that the companieswant to take maximum advantage of it. In the company the brand is a great resource with analready known identity and established values that can help new products to enter the market. Toextend the brand is a popular growth strategy but it is important to do it properly in order not tofail. J Lindeberg and Peak Performance are two Swedish fashion companies which both havemade brand extensions.

In offshore oil production FMC Subsea systems use a product called cap. The cap´s mainly task is to protect hubface and seal areas on inboard hub against dirt, corrosion and mechanical damage under installation of a subsea system. A new model of a cap has been designed and analysed using finite element method. The model is called KC3-12 and has a new function, emergency release, which is a backup method for the ROV (remote operated vehicle) to release the cap from the hubface when it is placed under water. The cap KC3-12 was found to fulfil the criteria under the test load pressure, according to ASME VIII, div2.

This thesis aims to contribute to improved functional procurement of photovoltaic systems, PV systems. Functional procurement means that criteria concerning a function are set rather than specifying technical details or products. Possible advantages and difficulties in using functional procurement have been analyzed by interviews, simulations and a case study. Electricity production and surplus production for different scenarios have been simulated via MATLAB. The MATLAB script was also used to generate rules of thumb on feasible solar fraction for six different load profiles; a church, a farm, a car mechanic, an office, an industry and an apartment building.

This master thesis covers the development of an automatic tuning process for the existing speed controller for drive systems. The drive systems are resonant two-mass systems where a motor is used to drive a load connected by a shaft. The developed method relies heavily on system identification and the construction of a complete mechanical model of the process. With this approach, the common problem with poor load speed control that derives from measuring only the motor speed can be addressed and solved for a majority of such processes.The automatic tuning method has along with general test functions been implemented in a complete tool for automatic tuning, testing and performance evaluation and reporting for drive systems..

To be able to move around without having to think about each movement is for most people amatter of course. Todays society contributes to a life at high speed where the sparetime is oftenspend doing somekind of sport, even extreme sports which earlier only a few people wheredoing. This leads to not only good health effects but also to more injuries. One of the mostcommon injuries is the knee injury.Capio Artro Clinic is a clinic specialized in sports medicine and particulary patients with injuriesin knee, shoulder, foot, hip or elbow. They perform a great part of all the crucial ligamentsurgeries in Sweden and has therefor also a lot of patients in need for rehabilitation of the knee.During the rehabilitation the load of the injuried knee is increased in steps.

From the mid 19th century to the early 20th century about 1.2 million Swedes left Sweden for a new life in America. Three parishes in Örebro län is at the centre of the research of this essay. The time span of this essay ranges from 1856-1915, divided into three periods; 1856-1870, 1881-1895 and 1901-1915. The main objective has been to compare the three parishes with each other, with Örebro län and with Sweden. What I have wanted to examine has been the following: How many people from each parish emigrated during each period? How many were men, women and children up to the age of 15? In the analysis part of the essay the results were compared parish with parish, and with Örebro län and Sweden.

From the mid 19th century to the early 20th century about 1.2 million Swedes left Sweden for a new life in America. Three parishes in Örebro län is at the centre of the research of this essay. The time span of this essay ranges from 1856-1915, divided into three periods; 1856-1870, 1881-1895 and 1901-1915. The main objective has been to compare the three parishes with each other, with Örebro län and with Sweden. What I have wanted to examine has been the following: How many people from each parish emigrated during each period? How many were men, women and children up to the age of 15? In the analysis part of the essay the results were compared parish with parish, and with Örebro län and Sweden.The analysis showed that the emigration of three parishes is commensurate with the Swedish emigration history.

For systems with multicore processors contention for shared resources is a problem that occurs when several memory-intensive processes are executed in parallel within the same memory domain. This contention has a direct influence on the performance of the system and is a complex problem that has been recognized for a long time. An attractive and actively studied way to minimize this problem is by using a process scheduler adapted to allocate processor cores in a way such that contention for shared resources is minimized.With the introduction of multicore NUMA-systems (Non-Uniform Memory Access) the situation has become even more complex. In these systems the access time for processor cores to different memory domains vary depending on factors such as distance and load. Thus, the process scheduler also has to consider where the memory of each process is placed to minimize the distance and balance the load on each memory domain.This report presents a user-level process scheduler for a NUMA-system based on the multicore processor Tilera TILEPro64.

The Anybus CompactCom modules are today using the Anybus NP30 processor. These modules are used for communication between industrial machines and larger network protocols. The communication loads on these systems are increasing every day and the limiting factor for the system is the processor.HMS, the company that develops the Anybus CompactCom, has shown interest for a benchmark test between the old processor and a new processor, ARM Cortex-M3. This project includes that benchmark. To be able to get results that reflect reality a test environment was created to simulate Anybus CompactCom conditions.

The aim of this present study was to determine and evaluate whether the presence of brooktrout (Salvelinus fontinalis) and sediment load may be a threat against the reproduction anddistribution of freshwater pearl mussel (Margaritifera margaritifera) in a creek located innorthern Sweden. Freshwater pearl mussel is an endangered species and is dependent ofbrown trout (Salmo trutta) to reproduce. Therefore there are concerns of indirect effects onthe population of pearl mussel by competition between brown trout and brook trout. Ditchesfrom a nearby gravel road have been fixed to lower the sediment load into the creek. I tried toevaluate this action plan.