Until the beginning of the 1900:th century the paper making process was handicraft. The paper machines that have been developed since then are as impressing in size as fascinating when it comes to the technique. The process has always been improved to give a better paper for lower costs, with as short manufacture time as possible. Stratified forming has been a reality since 1830. From the beginning it was applied to board and paperboard.

Title: Bottleneck management through materials administration Course:  4FE05EAuthors:  Mikael Karlsson and Johannes Mueller  Examiner: Helena ForslundKey words:  Bottleneck management, material management, process description, timber, proceduresPurpose:   The objective of this study is divided into three parts, all three parts of the purpose aim for the same goal. Namely, to improve the material management so that this enables the bottleneck in the planing mill to keep a continuous  flow, and thereby minimizing the risk for production stops at LB-Hus.  Part.  1:  Identify  and  analyze the material management  connected to  the planing mill  in order to identify problem areas.Part.2:  Identify  improvement potential  in the material management connected to the planing mill.  Part.3: Suggest improvements in the material management connected to the planing mill. Theoretical framework: Process mapping, inventory accounting, balance safety, inventory availability / service levels, safety stock and reorder point, forecasting and routine descriptions.Empirical foundation:  Interviews carried out at LB-House,  illustrated with the help of process maps and a description of each process.  Conclusions:  To work with  the  suggestions  given  and  to  follow  clear procedures  in  all  processes would  result in  a more  efficient  inventory management,  it would also present  a  solution  to  the problem regarding the planing mill being a bottle neck.Suggestions for further research: Review and map the information flow from demand to production start.

Deposits can be formed in the paper machine due to sticky materials from wood and recycled paper. These deposits get stuck on process equipment and cause the product quality to deteriorate and the efficiency of the paper machine is reduced. The purpose of this thesis is to increase the understanding about deposits among machine operators, and to suggest methods that can be used to reduce the amount of deposits formed in Bravikens paper machines.To fulfill the purpose of the thesis a pre-study, a literature review and interviews with machine operators and production staff, were carried out. These methods led to the planning and creation of an education about deposits for machine operators.The education about deposits for machine operators consisted of an interactive lecture to introduce the subject of deposits and a subsequent discussion. This approach was chosen to give the machine operators the opportunity to discuss their work situation on the paper machines related to their new knowledge about deposits.

An often encountered problem when implementing a mass flow regulator in a rolling mill is the one with measurement of speed. The most widely used solution is to fit a pulse counter to a wheel that is in contact with the strip. Common problems with this design are for instance scratch marks on the strip and problems with the flatness measuring system.  One way of circumventing the aforementioned problems would be a non-contact measuring system. The market of today only offers systems based on the Doppler principle.This report evaluates three different systems for non-contact speed measurement. Important areas in the evaluation have been the ability to operate under normal rolling conditions, integration in existing control system and how well the sensor can be fitted to the rolling mill.

An often encountered problem when implementing a mass flow regulator in a rolling mill is the one with measurement of speed. The most widely used solution is to fit a pulse counter to a wheel that is in contact with the strip. Common problems with this design are for instance scratch marks on the strip and problems with the flatness measuring system.  One way of circumventing the aforementioned problems would be a non-contact measuring system. The market of today only offers systems based on the Doppler principle.This report evaluates three different systems for non-contact speed measurement. Important areas in the evaluation have been the ability to operate under normal rolling conditions, integration in existing control system and how well the sensor can be fitted to the rolling mill.

Det här arbetet omfattar en arkitekturstudie av ett framtida processnät för Hylte Mill. Arkitekturstudien innefattar en mall för hur den framtida miljön kan se ut. Arkitekturhypotesen skall användas som en modell för företaget och visualisera ett trådlöst nätverkssystem vilket skall hjälpa operatörer att hämta information från SCADA-systemen via pekplattor. Metoden som använts för att ta fram arkitekturen grundar sig på utformningen av så kallade vypunkter. Vypunkter är vyer som skapas för att identifiera relationen mellan olika användare och systemet.

The negative trend of newspapers reading gives the owner of several paper manufacturingcompanies in the West worries. Producers should be more concern to strengthen their marketpositions in order to maintain profitability in the Paper mills. Holmen Paper is a medium sizedPaper mill company with all of their production in Europe. Sales are mainly made to printingcompanies operating in European countries. In order to strengthen their economic strengthHolmen Paper needs to increase the market share in markets where they have the greatestprofit margins.

Hallsta Paper mill uses large amounts of water during the pulp and paper making processes. The wastewater is treated in two separate activated sludge processes referred to as BIO 1 and BIO 2. The main aim is to reduce the organic substance content, measured as COD (Chemical Oxygen Demand) before the wastewater is released into the environment. Since the effluent produced is very rich in organic substances, the addition of nitrogen (N) and phosphorus (P) are necessary to give satisfactory treatment results. Problems with sludge bulking sometimes occur which lead to increased levels of suspended matter and nutrients in the effluent.

People of the modern world consume more than they ever used to do. Because of the close correlation between consumption and the amount of waste, the waste volume is also expected to increase. The purpose of this study is to examine if some measures in the recycling process from Sweden could be implemented in Indonesia. In fact, Indonesia is one of the countries in which the waste management system is struggling. Tetra Pak, one of the world leading producer of food packaging, is studied in this report.

Freedom of speech has been a well discussed subject. Great philosophers and theoretics like Plato, Voltaire, Locke and Mill have again and again showed the importance of freedom of speech. Since the world have become bystanders to a series of events that can only classify as crimes aganst freedom of speech, it has become more important to study the phenomenon and analyse it. By finding cases where the freedom of speech has been compromised and analyse them in frames of three different theories, the argument of truth, the argument of democracy and the argument of tolerance, this paper makes the boundaries of freedom of speech a little clearer, and also makes a discussion about how reasonable the boundaries are possible. Everything according to the three theories.

In the process of making carton boards into Skoghall Mill, are great quantities of water being contaminated. This water has to be treated before it is possible to release into the recipient, Kattfjorden. One of the contaminations that is important to extract from the wastewater, is organic carbon (measured as TOC-total organic carbon) because microbiological breakdown can lead to the bottom becomig free of oxygen.The wastewater treatment at Skoghall Mill is done through an external wastewater treatment that is located at the factory. The biological treatment (aerated lagoon) is a 140 000 m3 water pool with surface aerator, which is give oxygen to the water. In the lagoon live microorganisms who performs the biggest part of the TOC-reduction.One problem with the lagoon is that the treatment of TOC is considerably worse during wintertime than during summertime.

Åmotfors Bruk AB (ÅBAB) has today an inefficient production of steam for the manufacturing of paper. Unpredictable energy prices and modernisation of the current equipment has been the underlying factors to invest in a thermal power plant, mainly driven by garbage. This facility will not only use the steam for paper production, it will also generate electricity through a steam turbine. Today, when a fault on the supplying line occurs which leads to disconnection of the external grid, all the support of electricity to Åmotfors Bruk (ÅB) will disappear. This will lead to major interruptions in the paper production, which will cause severe economical losses.

The report is part of the university´engineer program within Industrial Organization and Economics with specialization in Logistics and Managment at Jönköping´s university.Skoghall´s mill underlies a large supply chain, which means there should be a lot of areas in need of small improvement measures. This report illustrates a small part of one of these areas and is focused on the loading distribution services in the terminal Vänern.At the moment there´s a very unequal load of the load carriers SECU box and Container at the terminal. Skoghall´s mill has the desire to equalize the high and low load levels of the 2 loading carriers named previously. One of the options to solve the problem is to set a limit of how much the carriers can load per week or per day. The mill also wants it to be investigated if the proposition would influence the customers in any way and if both the company and its customers could handle a lower level of delivery services in case the proposition was to be applied.The goal to be achieved with this thesis is to provide balance to the unequall loading of the 2 load carriers, SECU and Container, and investigate whether or not the Skoghall´s mill´s customers, could manage the lower degree of delivery service that the proposition would imply.For this goal to be achieved, random sample investigations were taken from orders of a customer that is provided with SECU load carriers and the same was made with a Container´s customer.

Fuel pellets are in Sweden mainly produced from sawdust and cutter shavings. Before the pelletising process the raw material is dried to attain consistent moisture content and ground up in a hammer mill. In the densification process (pelletising) the ground material is forced through holes in a rotating die. This heats up the wood particles which cause them to soften and self bond. After the process the pellets are cooled, sieved and bagged. The milling process creates a wide range of particle sizes.

This thesis work is made by Torbjörn Johansson on Karlstad University for Uddeholms AB. The assignment in this thesis work was to investigate tough cutting in three different tool steels: Vanadis 4 Extra, Vancron 40 and Sverker 21. The research was to compare the wear of the tool after cutting in each one of the tool steel alloys. The research was also made to see if the tool cutting in Vancron 40 has a better wear than the tool cutting in Vanadis 4 Extra and also compare the results with Sverker 21. All three of these alloys are a part of Uddeholms AB:s range of products, and is used in applications like forming tools and knife tools. Vancron 40 is a powder steel with a very good combination of mechanical properties like ductility, adhesive strength and hardness.