Modern forestry requires a high degree of machine traffic for clear felling and scarification operations. The machines most frequently used are big and the traffic often results in tracks on the forest ground. There are many small streams running through a forest, in connection to logging operations, machines might cross these frequently. These crossings could result in the erosion of fine particulate inorganic matter, which ends up in the stream. The aim of this thesis was to give a general description of small forest streams of order-one in the county of Värmland and to determine the frequency of machine tracks in small streams.

One of the most important components of a harvester is the crane. Most harvester cranes are only possible to pivot (or horizontally rotate) at the crane pillar. Cranab in Vindeln, Sweden, has developed a new type of harvester crane which has an extra pivot point on the outer boom. This makes it possible to reach around residual trees, easing thinning work in dense stands. The aim of the study was to analyze if the use of a pivoting outer boom (POB) crane gave an increase in thinning production and if there were any differences in time consumption between the work elements for the POB crane and a conventional crane. A Valmet 911.3 equipped with a POB crane was used in the study.

Our Bachelor?s Thesies has been performed in co-operation with Cellplast Direkt AB inLaholm. Our task was to develop a construction that cuts gussets to ceiling disposition as isused to isolation.Our goal with our construction was to increase the degree of automation so that theproductivity increased and also meet the market which is getting tougher and tougher due tothe future business cycle.Cellplast Direkt gave us free hands in order to enable new ideas. A pair different principleproposal was developed and prepared to a final structure.The Bachelor?s Thesies resulted in one PLC - governed machine with three engines that runthree different moves, wich does that the degree of automation increases and the risk forerrors decreases.We have developed a complete production bases to Cellplast Direkt and our hope is that thecompany comes to produce the machine in the future..

To get the maximal output of your exercise in gym machines, there are different factorsto be considered. For example the strength of the muscle varies dependent on the positionof the muscles. To get the best results of the exercise the load has to reduce and increaseat specific positions.This study was made in cooperation with Caretaker Scandinavia AB, a company forsales, marketing and development in health care. They are general agent for Nordic Gymwho works with manufacturing of equipment and machines for gym and fitness.The aim of this study was to generate a method of measurement to evaluate and controlthe biomechanics of Nordic Gym´s workout equipment. A protocol for an ergonomicanalysis on the equipment has also been elaborated.One of the methods to measure the biomechanics was to measure the torque through thewhole movement.

The traditional view of maintenance is machine-based, where acute maintenance tasks are highly valued. Preventive maintenance is viewed as secondary and less desirable to work with. The more modern view is to regard maintenance as a process. The machine-driven tasks are still necessary but are viewed as a part of the big picture.The purpose of this study is to examine how to high light general difficulties concerning maintenance management to aid organizations to reflecting upon their own situation. The study is based upon a pilot study initiated by ProcessIT concerning relevant key figures in maintenance.

The degree project is performed at Metso Kamfab. The production is aimed on machines everything from handling of fiber to paper pulp. Metso Fiber and Kamfab are using Pro/Engineer for design and blueprint production. The processing department types the NC-programs in notepad on the basis of the blueprints, the CAD-dates that already is there are not used. The aim with the work is to study if Kamfab can use CAM-system for processing and production of programs for their NC-machines.

The technical development is advancing at high speed and now the turn has come for the traditional paper to digitalize into the so called e-paper. The newspaper industry has started to investigate the future possibilities of publishing the traditional newspapers on e-paper. Today?s newspapers are mostly financed by advertisement incomes, which makes the advertisers important players, who must be taken into consideration at an introduction of the e-paper. Since the e-paper does not exist as a finished product in the market today, in this essay we look into what kind of functions or services that can attract advertisers to the e-paper on the basis of the experiences made with the breakthrough of the web-newspapers.

In the electronic industrials, power control of AC motors is commonly used. For example power control of a washing machine motor, a vacuum cleaner motor or a coffee machine motor. The company Rejlers Ingenjörer AB has many projects where power control of AC motors is included. A prototype card for this task can save time and money for the company in the future and this is the reason for this thesis.The motors are power controlled by a TRIAC and control of the trigging pulses to the TRIAC. This card is modularly built and can easily be adapted for future projects where the power control of AC motors are included.The prototype card can be used as a subsystem in a larger electronics projects or as it is in lab environment for testing and evaluating new motors..

Uppsats för avläggande av filosofie kandidatexamen iKulturvård, Konservatorsprogrammet15 hpInstitutionen för kulturvårdGöteborgs universitet2012:21.

Costs of maintenance on combines are a subject of interest thus it constitute a large investment and cost for the individual farmer. Therefore it is important to have up to date knowledge and the right facts to be able to do reliable calculations on one of the largest investments for a farmer. The aim of this study was to compare costs of maintenance on combine/threshingmachine with the computer program for advising environmental issues in agriculture, STANK. Interviews took place and data were collected by handing out questionnaires to 20 farmers. A similar study conducted by Neuman (2003) investigated costs of maintenance and compared these with STANK. The results of this study have also been compared and examined related to data from SLA - Skogs och Lantarbetsgivarförbundet. The result shows that 18 out of 20 combines were given a higher cost of maintenance when using STANK compared to the numbers in this study.

The Master Thesis work this report is based upon has been conducted in cooperation with Svea Teknik AB. Svea Teknik is a consultant firm which is developing parts of a tunnel boring machine on behalf of Atlas Copco. The machine is being developed to mechanically excavate hard rock by fixating itself in the tunnel and then press a large rotating cutter-wheel equipped with disc-cutters against the tunnel wall. The disc-cutters are the tools that are in direct contact with the hard rock and are therefore exposed to extensive wear and needs to be replaced on a regular basis.The purpose of this Master Thesis has been to develop a service equipment that will enable time effective and safe changes of disc-cutters. The disc-cutters have a diameter of 17 inches and weigh about 130 kg.

This thesis work has been performed on request by SWT (Scandinavia WeldTech AB). SWT manufactures, develop and sell ready to assemble building systems for concrete rafter beam applications. The beams in this system consist of a u-beam that is welded to a flange. To be able to fill the beams with concrete there is holes in the beams top end. The holes are made in a ?punching machine?.  These holes are cut out and the remaining steel piece is bent down in the u-beam.

At a manufacturing company, due to the competition the price is reducedtowards the manufacturing cost. Therefore it is important to maintain control ofones costs and keep calculations up-to-date.This thesis deals with cost accounting at a aluminium-processing company. The report focuses on calculating machine cost per hour since the manufacturing costs are the major part of the total product cost.Managers on the company believe that the costs they use in calculations todayneither is up-to-date nor advantageous in a market aspect and due to that their calculations need to be revised. The machines cost per hour is a major part in the manufacturing calculation. The company wants to provide a competitive price that also covers their costs.

Six different Digital Proofing Systems from three different techniques have been evaluated as totechnique, printing quality, economy and usability. Digital proof from two paper qualities, coatedand uncoated, has been compared with references printed in offset, to see how good they match eachother. Only two Proofing Systems manage to print on reference paper. The other Proofing Systemsuse special paper for digital proof.Measurements and visuell judgement show that the Digital Proofing Systems visualise referencepictures with quite good quality. Proof optimised for coated paper visualise the colours with goodresult.

The Swedish pulp and paper industry meets higher demand for energy efficiencyi mprovements with increasing energy prices and changes in the Swedish renewable energy certificate system. One action of energy efficiency improvement is by using secondary heat, that otherwise would have been treated as waste heat, for use in a system with lower temperature demands. The aim of this Master´s thesis is to identify possible secondary heat sources in a typical Swedish pulp and paper mill and to investigate what economic benefits the secondary heat will provide when being used for pre heating of wood chips to a kraft digester.The Master´s thesis focuses on three secondary heat sources; dry warm air, warm water and moisture saturated warm air located inside the pulp or paper mill. Two types of kraft digesters are simulated within this study, a typical Scandinavian digester and a modern twin vessel steam phase digester.Due to quality aspects and low temperature level drying is the drying technology with dry warm air rejected. Using warm water in direct contact with wood chips increases the quantity of water to the evaporation plant and thus reduced pulp or paper production and is therefore also rejected.