This report is about the issue with decreasing production rate mainly caused by failuresrelated to the multiswitch. The multiswitch is a machine at Gefleortens Mejeriföreningwhich has the function of distributing milk cartons from one incoming track into fiveoutgoing tracks. Milk cartons who gets stuck and there by causes the production to stop,is the mainly problem with this constructionThe purpose with this report is to understand the causing factors and make suggestions which can help solving these factors. By analyzing the machine during production, having contact with different suppliers, searching internet for information, 3d-cad drawings and the complementary with personal experiences, this machine has  been evaluated and as a result of this new problem has come to be known.The discovered problems was analyzed and resulted in new suggestions for alternative options. Later the most functional results was chosen and put as a suggestion for the new model.A new machine built with the suggestions from this report assures to be well adapted to the environment at Gefleortens Mejeriföreing and the problems it causes..

AbstractThis thesis is the final part of the Innovation and Design Engineering Programme (180 ECTS credits)at the Faculty of Health, Nature and Engineering Science at Karlstad University. The extent of thisthesis is 22.5 ECTS credits and has been performed independently by Hannes Jernberg during thespring of 2013. Metso Paper Karlstad AB is the task maker of this project, and Arvid Johansson is thecompany Representative. Metso Paper Karlstad AB is one of the world leading developer andmanufacturer of tissue Paper machines.In the current situation, the company has developed and patented a power management systembased on a Cross Flow Turbine. The current construction is limited to a paper width of 2.9 meters.The company wants to take advantage of all the opportunities provided by the patents, to develop aturbine solution Paper machine with a paper width that is wider than 5.5 meters, and give the abilityto manufacture paper for lower energy consumption which is an important part of the production asit is very energy intensive.Problems arise with the increasing length of the turbine, ultimately resulting in that the deflectionbecomes too big and that the momentums, due to the increased torque the turbine blades breaks.By applying the design process, this work has resulted in a number of potential solutions to theproblem.

Abstract The main aim for this research is to come to an understanding for why young people choose to apply for the machine program when the time comes for the students to make their choice of upper secondary school program. The second aim for this research is to try and come to an understanding on how to make the machine program more interesting for future students to apply to.  The method of this research is quality method with the usage of interviews. With a total of six students in the first grade going on a school in the middle part of the country I tried to get answers to my questions. There are many things that affect students when they are facing what gymnasium program to choose and a very common answer by students in this study is that friends and work after school are some of the reasons for why students choose, for example, the machine program. The study also shows that parents has less influence of the students choice of gymnasium program and in fact, all students in this study made the choice to pick the machine program as their gymnasium program, but not always the machine program as their first choice. With the comparison of similar studies with my study the results are often in line with what other scientist have come up with.

The research in this paper aims to producing a home version machine thatcan dry and make biological waste into compact pellets. This product ismade primarily for those who want to improve the environment and reducethe energy consuming process of separating the biological leftovers fromother waste in the large processing plants and save money due to reducedpickups of waste. Since there is no commercially available product thatdoes what we want to achieve we had to start from the beginning with boththe design and the mechanical aspects. The result is a machine, that fits inour homes, and in an easy and inexpensive way reduces the amount ofbiological waste that needs to be collected by the public wastetransportation system. This is done without reducing any of the energy inthe waste and it can still be used to compost or by large-scale plants that usethe waste to make electricity.

This is a study in the field of Music Information Retrieval (MIR) concerning classification of musicgenre. The study uses a music listening experiment and machine learning methods to determinewhether or not the drum sounds from different songs contain sufficient information to classifygenre.MIR methods are used to extract data from the audio signals. The data is used together with theclassification results of the listening experiment to train different machine learning algorithms toclassify the songs in different genres.The results indicate that using only drum sounds for genre classifications works well, both forlisteners and for machine learning methods..

As a student during my studies, I have been told about entrepreneurs who have red numbers in their financial statements, and there is a forest machine operator shortage in Sweden. The basic idea of this thesis was to examine the underlying factors that may have caused the problems described above. The aim of this thesis was to investigate the factors that create stress and job satisfaction as a forest machine operator. The study was performed as a comparison between forest companies own harvesting teams and entrepreneur teams to investigate if there are any differences in stress and job satisfaction between the two different types of team. The study was conducted in collaboration with SCA Skog. The material for this study was collected by doing interviews with SCA's harvesting teams. A total of 27 forest machine operators were interviewed, divided into a total of 10 separate harvesting teams. It was very similar between the different type of teams, which situations the operators experienced stress.

As the final course in the education ?University Diploma Programme for Process Operators? there is a thesis in cooperation with a company required.This thesis is about operator maintenance and 5S made at Metsä Board in Husum.In this report you can read my opinions and conclusions based on literature studies and the interviews that have been made with the staff at PM6 (the Paper machine).I chose to focus on the theory of lean, 5S and operator maintenance because it covers the area of this thesis.The operators shall do their rounds to make sure that the equipment works fine. They shall also write down things that they notice in a checklist. This is not done as it should be and the question is: can this be solved by using 5S?My conclusion of this thesis are:Better review of the task so that everyone is involved.

Forest ebeaver is, equipped as a bio-energy harvester, approximately four and a half meter long and weigh just over two tons. The main purpose of this report is to find out whether a small machine like Forest ebeaver can be profitable used in early thinning. To find this out a study has been made using the machine to thin in a young pine stand..

The project was carried out with SwedSafe AB, engaged in hearing and manufacture of earplugs. Since the company is a world leader in the sale of these products, it is important that they keep a higher level of quality of these products.Production of earplugs is currently a automated manufacturing process that is divided into four conveyor belts and one of the conveyor belts is what will be affected in the project. The belt affected during this process is exposed to various elements such as filling, closing, fermentation and extraction of products. Because the belt gets dirty, degraded products and the work environment is affected. To increase the quality of products and improve the working environment requires an automatic cleaning process, which collects dirt from the belt.The aim of the project is to design a machine that prevents the belt from becoming dirty, preserve molds clean and improve the working environment without disrupting production.

Reporting harvested and forwarded volumes are important for the forest industry as it provides information of the size of the stock and facilitates logistics. Figures from Holmen Skog show low reporting frequency. The purpose of this study is to investigate the reason and find suggestions for improvement. A total of 17 machine operators were interviewed using a questionnaire combined with open questions. The results show that the majority of the machine operators find it simple to use the reporting system, although, some of them reports that it doesn?t always work as supposed to.

The scarcity of qualified forest machine operators as well as the increased competition for competent machine operators among others from the mining industry in Norrland, were the reasons to investigate what attracts and what deters active and potential forest machine operators to the occupation. An interview study was conducted among four groups with four persons in each group. The groups were students in year 1 and 3 respectively at a forestry school at upper secondary school level as well as employees of a forest company and employees of contractors. The majority of all respondents were of the opinion that their interests in machines had been important for the choice of occupation. But for the active machine operators both the interest in the forest and their interest for machines have had importance for choosing this occupation.

This paper is the result of a case study conducted at Uppåkra Mekaniska AB during the spring of 2006. The task that was presented by Uppåkra was to develop a basis for a decision for the planning activities at the company, so that in the future they can create lot-sizes which are based upon a total cost perspective. Total cost in regards to lot-sizing is defined as the sum of the administrative reordering costs and warehousing cost per stock keeping unit.To collect data a series of interviews and observations were conducted. This data was then used during the lot-sizing simulation and analysis. The 15 units that the simulation was conducted on were grouped into three item classes depending how many different machine setups they required during the production process.

Most companies have a bottleneck in their production, that is a constraining re-source. When the demand is higher than the capacity in the constraining resource it is impossible to produce the demanded output. This problem leads to delayed deliveries, unhappy customers and ultimately to decreased revenue. Bottlenecks therefore has a significant role in production and must be handled thereof.MW Power in Sävsjö, Sweden designs and manufactures water and steam boilers for the customer's unique needs. MW Power invested in a new plasma cutting ma-chine but the machine has not reached the expected capacity.

Until the beginning of the 1900:th century the paper making process was handicraft. The Paper machines that have been developed since then are as impressing in size as fascinating when it comes to the technique. The process has always been improved to give a better paper for lower costs, with as short manufacture time as possible. Stratified forming has been a reality since 1830. From the beginning it was applied to board and paperboard.

The vision of this thesis was to create a concept that can be used as a base for amachine construction. The purpose of this project was to use different methods todevelop a concept that on the best way meets the sat up requirements. This projecthas been divided into three stages/parts; principle, primary and the final solutionstage.This thesis has been conducted in collaboration with Västkustägg AB. It is aconstruction project designed to construct a machine that will automatically putlabels on the egg packages. Västkust AB wanted to automate this process.