Manzai (??) is a Japanese comedy style similar to stand-up comedy but done by two people in the form of a dialogue. One is the Boke ?Funny man? and the other the Tsukkomi ?Straight man?. This work examines how manzai discourse is structured to create comedy by using the framework postulated by Abe (2006).

This thesis for the Master of Science degree was performed at Oppunda Electronics AB. The assignment was to further develop an existing prototype of a dispensing equipment. The dispensing equipment doses a kind of glue, bonding which dentist use to mend teeth. The dispensing equipment is adjusted to dose 12 micro litres of bonding. With the dispensing equipment SafeBond Electronic the user can reduce the bonding consumption with approximately 50 percent.

The research within the management control systems-field and more specifically performance management has been rather shallow and not much has happened the last decades besides the balanced scorecard. The researchers see a lack of studies focusing on the effects of an integrated performance management system and also how it affects the different hierarchical levels and the tasks to perform.We decided to perform an essay with case study-characteristics by looking at both the strategic and tactical level at Volvo Group, or more specifically Group Trucks. We performed three different interviews, one at the group level and two at the division level. The aim was to see what effect an integrated performance management system had on the tactical level (i.e. the divisions).Our findings and corresponding analysis suggested that Volvo was a rather centralized company in order to get the performance management system to work by enabling a ?weekly control?.

During spring 2009 a three meter tall and laughing robot was developed in collaboration between Royal Institute of Technology and Royal University College of Fine Arts. The robots function and esthetics is based on an existing toy robot called Elmo. Elmo is 30 cm tall but now the goal was to make it 1000 times bigger in order to present it on the spring exhibition of Royal University College of Fine Arts. Due to only four months of developing and building time a demand of fast determination and good planning was required. In order to make a good structure for the project it is divided into five phases: Analysis of Elmo, planning, concept development, detail construction and finally product development and testing.In the first phase valuable knowledge is obtained according to the movements and geometry of Elmo.

Problem: The corrugated board industry is highly affected by customer uncertainty, various demands and short delivery times. In combination with a complex multi-step production process managers have to be able to identify bottle-necks and gain knowledge and understanding of how different changes in process will affect the production output. <br/><br/>Purpose: The purpose of this master thesis is twofold, (1) to examine applicability of complexity theory through agent-based modelling on a production process (2) to identify improvement areas in order to increase the production output at SKS production site in Eslöv, by modelling and simulating the production process through an agent-based model. <br/><br/>Method: The chosen method of this study is a combination of a case study and a complex system approach. The empirical data was collected through interviews, observation and document studies which were analysed through an agent-based simulation model.

This master thesis project at KTH is performed in the Mechanical and Aerospace Engineeringdepartment at University of Florida (UF). The thesis is a small part of a gas turbine researchproject where a vapour absorption refrigeration system (VARS) and a high pressure regenerativeturbine engine (HPRTE) are integrated together. The main objective is to build a computermodel of the VARS. The computer model is supposed to be used to analyse the off-designperformance of the VARS and should also be easy to integrate as a subroutine in a more complexsystem model. To model the VARS some knowledge of the absorbent/refrigerant mixture had tobe well known, in this case a mixture of ammonia and water.

The poultry red mite, Dermanyssus gallinae, is a common problem in poultry facilities, causing great discomfort for the hens and effecting the production economically. Few efficient acaricides are available and there is a need for new control methods since resistance has become a problem in some cases. The aim of this study was to evaluate the efficiency of the new liquid silica control agent Ectopar, on the poultry red mite. An initial in vitro test of Ectopar and its two components individually was performed, where live mites were sealed in together with filter paper impregnated with one of the three solutions prepared. The survival of the mites was thereafter recorded repeatedly during a period of 120 hours and compared to a control. For the field study, two poultry farms with different housing systems were used, one with furnished cages (farm 1) and one with a single tier floor system (farm 2).

In many products a compromise between ground clearance and the required space to store the product has to be made. This problem attracted the attention of the authors of this thesis.The objective of this project is to develop a functioning solution to a foldable wheel. The solution should be applicable to several types of product groups. A limitation for this work has been made so that the work only covers solutions for lighter vehicles.The purpose is to drive this project forward, so that a solution can be found. Furthermore the purpose of the report is to clarify how the authors proceeded to design and construct the wheel according to a fixed specification.

Mechanical relays are more and more being replaced with semiconductortechnology. In this thesis it is investigated if and how the larger loads couldbe controlled by transistors. The main part of this work aims to create andverify a solution that can control the starter motor, as well as protect it incase of any failure. The different malfunctions that the solution protectsagainst is high current, too high peak current, low current, maximum cranktime and minimum cool off time. The timers also protect indirectly againstoverheating of the starter engine.The transistors used are BTS555, from Infineon.

This Master Thesis has been conducted as an assignment of the Swedish Defence MaterialAdministration and the Swedish Armed Forces and aims to examine the Target Location Error(TLE) of a Forward Observer System. The targeting accuracy of the system is vital if the systemis to be used as a sensor for precision munitions. The analyzed system, EOI (FOI 2000), wasdelivered to the Swedish Armed Forces in 2007. The targeting sequence starts with deciding theposition of the system with a GPS-receiver, continues with methods where the north direction issettled and ends by measuring the distance, direction and elevation to the target. When allparameters have been measured the system calculates the position of the target.

The aim for this study was to investigate, analyze and compare the way Sweden's main five news outlets portray and frame Swedish supporter culture surrounding football. In order to do so we formulated four research questions, all with the purpose to operationalize both the questions and the theories into data and results. The questions reads as follows: 1. What are the dominant portrayals in Swedish news outlets presentation of supporter culture? 2.

In this report the two authors, and project contributors alike, describe their work withdeveloping a solar cooker intended for usage in the developing countries of the world.Specifically, the work aims at developing a new, solar heat driven cooking device, possiblybased upon the current product. This should, in comparison to the current product, be lighter,easier to transport and to produce. Also, the new product?s production mustn?t be more costlythan today and the included materials and components must be obtainable from within theBolivian national borders where the product is currently produced. During the project, certainadvantages with a more efficient, and, above all, a more moderately priced product, werediscovered.

Volvo Construction Equipment is a world leading company in construction machinery. Tomaintain the best products, development is prioritized. The master thesis regards sound reductionof the hydraulic system on a wheel loader. The background to the master thesis is asimulation made on the hydraulic system, performed autumn 2005. The result of the simulationshows that the energy of the pressure ripple is reduced when the paralleled hydraulicpumps are phase shifted and reduces each others pump pulsations.

This report describes the construction work of a radar antenna for the radar systemCARABAS. CARABAS is a long wave airborne ground radar that has been developed bySAAB Microwave Systems and will now be mounted on a small helicopter, Schweizer 300.The antenna should be able to fold up and down. When the radar is in use the antenna islowered and under transport, start and landing the antenna is folded up. An emergency dropfunction should also be included in the design of CARABAS III.The extent of this report includes construction of the antenna, frame structure attached to thehelicopter, mechanism for folding the antenna up and down and mechanism for emergencydrop function. The mechanical design of the antenna and frame structure is based on modaland stress analysis, vibration measurement of Schweizer 300 and frequency analysis, andcalculations regarding aerodynamic drag and mechanics.The exciting frequencies of the helicopter and accelerations at those frequencies weredetermined by vibration measurement and frequency analysis.

This thesis concerns waste management on construction sites and was conducted on behalf of ICA Fastigheter.Areas of concern:How can an environmentally-efficient waste management system on construction sites be defined? What potential exists for exploiting the waste resources that are generated?How can the waste management be optimised by reducing the quantity of waste and by optimal sorting?How can the client of a project influence the waste management?The purpose of the work was to investigate sustainable waste management in the building and construction sector and to highlight waste as a resource from an environmental and economic perspective.The aim of the work was to define an environmentally-efficient waste management system, to analyse the potential that exists in waste management and to draw up guidelines for optimal waste management.The method consisted of a literature study, two visits to construction sites and four interviews.An environmentally-efficient waste management system means that the waste is managed in the following order of priority:Prevention     Reuse  Recycling     Energy recoveryLandfill     The prevention of waste is an important area that has not been adequately explored by the building and construction industry. The quantities of waste could decrease with the implementation of measures such as ordering materials in the dimensions required, prefabricated components, logistics centres with Just-In-Time deliveries, less and improved packaging and less wrapping. The reuse of waste materials and temporary apparatus as well as the use of a return pallet system are examples of reuse that reduces the quantities of waste.In most cases the source sorting work is a matter of course and the proportion going to landfill is down at a low level. The source sorting can be optimised by sorting all materials that can be reused and recycled to use them as a resource.