Due to increasing product availability and higher demands on fast deliveries, the competition between companies is growing. To be able to satisfy the customers? requests an efficient logistics system with short throughput time is required. By using tools associated with Lean production companies are able to make great improvements in their manufacturing systems and reduce lead times to satisfy customer demands.There are two classifications associated with manufacturing, high variety and low volume (HVLV) and low volume and high variety (LVHV). The general belief is that the concept of Lean production is difficult to implement in a production environment with high variety and low volume due to the concept being adapted to mass production.

Product development cycles become shorter and shorter. The time from idea to market has become an important competitive factor. Despite this, methods used for making the product development process faster are surrounded with uncertainty about their efficiency. The purpose of the thesis is to describe the pros and cons of ?best practice? methods for shortening lead times and how these methods effect the lead times in research and development.

The RoHS Directive was introduced in order to restrict hazardous substances in Electrical and Electronic Equipment, EEE. It currently restricts the use of six hazardous substances/compounds; cadmium, lead, mercury, hexavalent chromium, PBB, and PBDE. The RoHS Directive currently includes category 1-7 and 10 in the categories of EEE listed in Annex 1A to the WEEE-Directive (Waste of EEE). The aim with the report is to investigate and elucidate prospects and obstacles to increase the scope of RoHS. This report mainly considers the inclusion of product categories 8 (Medical Devices) and 9 (Monitoring and Control Instruments).

The purpose of this study is to increase the understanding of activities, flows and waste in a company's production process. By performing a value stream analysis, non-value adding activities are identified in a production process and then the suggested improvements that can reduce lead times will be stated. The value-stream mapping identifies the flow of information and the flow of material in a production process and this provides the basis for the identification of non-value adding activities.We conducted the study at Lammhults Möbel AB in Lammhult Sweden, where the production flow of Spira-21 has been investigated. This to identify any non-value adding activities that affect the flow negative and consumes time and money in a non-value adding way.A reasonable approach for the project was taken by studying the methodologies and theories. We conducted interviews and site surveys at Lammhults Möbel AB where the flow of information and material in the production process were investigated.

This report is the documentation of a project in the education Master of Science in Mechanical Engineering. The project was carried out at Alfakonsult AB. The purpose of the project was to map out the transference of information between the different operators in the supply chain of medicine in Sweden and to analyse this in order to reduce lead-time and the total throughputtime. The supply chain of medicine in Sweden consists of producers, distributors, one wholesaler, prescribers and patients. The mapping of the transference of information showed that most operators in the supply chain have done well introducing technical aids to facilitate the transference of information.

PurposeThe purpose of this thesis is to provide a deeper understanding of how e-commercecompanies within the fashion industry are working with lead times and illustrate andanalyse differences and similarities between companies.Research question- In which ways are e-commerce companies within the fashion industry working withshort lead times?MethodologyThis thesis is based on a qualitative research method in order to achieve a greaterunderstanding of the chosen topic, of how the chosen companies are operating and toprovide room to our own interpretations and reflections. Interviews through telephonewere used to gather the empirical data from six different e-commerce companies withinthe fashion industry.ConclusionsAfter completing the theoretical and empirical analysis it can be concluded that leadtimes are considered essential for all of the participating companies but there is adifference in which way they look at, and how they work with lead times. Somecompanies stressed that short lead times are an important aspect of competition andclaimed that this is something they are constantly working with. For others the balanceand matching of supply and demand was the most important factor rather than toachieve short lead times.

Parallel imports often lead to lowered prices and is therefore regarded as good from a consumer's point of view. From a business'point of view this is not always the case. When do parallel imports occur? Is it possible to prevent parallel imports to protect an introduction of a product in another member state? The purpose of this thesis is to present situations where parallel imports occur and to see if it is compatible with competition law to prevent parallel imports. Furthermore I will analyse the future development after the group exemption of vertical restraints enters into force in June 2000.

No accidents or injuries should occur because of our public health care. It should be a place with high security and good quality in order to avoid this type of accidents. This is a tough situation when the public health care organization should have as good quality as possible despite savings. It is difficult for middle managers to improve patient safety in the absence of money.The purpose of this study is to explain the work with patient safety that middle manager perform during saving times. The perspective we will look into is how they work with patient safety as an ongoing change.

This thesis describes the universalization, improvement and further development of acompact crane support frame for flatbed trucks. The work has been conducted at Eloch Fordonsteknik AB (henceforth EFAB) in Uppsala.The aim of the work has been to shorten the assembly time of the product. By doingso, the product can be kept on shelf, which in turn results in shorter lead time. Thishas been done by universalizing the support frame to be compatible with most of thechassis EFAB works with. Additionally, the entire construction has been made lighter,which will make it a more attractive choice for customers.A pre-study was conducted and information was gathered internally, as well asexternally, in order to ascertain that no limitation or possibility was overlookedduring the course of the project.One such limitation has been the geometry of the truck bed that the support frameshall be compatible with.

During the last couple of years many sectors and markets have had an increase in the competitive situation, this has meant that being cost effective have become more essential if organizations want to stay in business and be competitive. Thus, one crucial issue has become how to utilize the resources already available within the organization. Organizations can thoroughly plan and control personnel resources in order to become more efficient. But to become more cost effective also means taking into consideration several key figures, productivity being one of the more important figures.Onninen, a wholesaler which has one of its two central warehouses in Örebro has experienced this issue, i.e. an increase in competitive situation in their market.

Today, a large proportion of wood supplied for the Swedish forest industry is bought from private forest owners while forest companies at the same time provide the forest owners with services such as logging services and transportation. Today, forest companies work extensively with keeping the time used for transport and logging short. But what does the private forest owners think about the time required for the timber deal, also called lead time, and the different parts of the timber deal. In this thesis, the forest owners? perception of the different lead times in their contracts with Stora Enso and their communication with the purchasers is examined.

A report has been made at a company in Borås at a company called ACG Nyström. Thecompany is today international and is marketing advanced equipment, systems and furthereducation to the manufacturing industry. A part of ACG Nyström?s production is a machinethey call Unimat. ACG Nyström doesn?t just stand for the actual production of the machine,but also for assembling and installation of the machine at the final customer.

A mobile testing application using Unity was developed to analyse what impact button sizes and button layouts has on the accuracy of touch as well as the time to finish a labyrinth. This was tested on a Nexus 4 phone. 28 users navigated a small object through a labyrinth in which they collect keys to open the door to the exit. Each participant did the test 6 times with different combinations of button size and button layout each time, done in a random order. Hits, misses, completion time, order of button size and order of button layout was collected and then visualized using R.

The purpose of this paper was to identify the elements and the alloys that five objects found in Birka consist of and to examine whether there are any significant differences between the presumably imported and domestic objects. The material was analyzed using a scanning electron microscope (SEM) which was equipped with an energy dispersive X-ray spectrometer (EDS) in order to identify the elements that are present and the alloys that the objects are made of. Then the SEM results were compared with the results of previous analyzes that have been performed on finds from Birka in order to investigate how the objects differ in elemental composition and to find out if there are any significant differences between them. The results showed that the objects? content of the elements analyzed varies as the copper alloys the objects are made of.

The environmental monitoring in Sweden has been developed by several different parties and is now being coordinated and made more effective in order to meet the current demands on high quality information regarding the state of the environment. Sweden has been divided into five different water districts based on watershed areas because of requirements in the Water Directive of the EU. In Sweden there are two common types of environmental monitoring programs used to gather information on changes in time and in space. Currently both these two types are used for lakes in the water district of the western sea but only one is used for watersheds. The purpose of this report is to supply basic information regarding the possible need for a second environmental monitoring program for watersheds in order to better describe the spatial variation within the district as well as to determine the number of samples necessary in order to describe the district over time and space.