Syftet med detta arbete är att simulera ett värmesystem i COMSOL Multiphysics, Pipe Flow Module, Non-Isothermal Pipe Flow som innehåller ekvationer och randvillkor för att modellera inkompressibel strömning och värmeöverföring i rör.Data om processen och dess komponenter har samlats in från industrin där arbetet är utfört och i vissa fall modifierats för att bättre beskrivas i programmet.Utifrån insamlad data har en modell byggts upp och två simuleringar har gjorts. En stationär för starten av systemet, den har sedan legat till grund för en dynamisk som simulerar förloppet från start till normaldrift.Tiden det tar för det aktuella fallet att nå drifttemperatur är 16 timmar. En felströmning upptäcktes samt att en av pumparna inte kommer att klara en start från 20 °C..

The thesis work of 15 credits has been performed to interest of Norrtälje ElektronikPartner AB (NEP) in Norrtälje. The aim of the thesis was to develop a prototype for an integrated digital multimeter, designed for one of NEP's proprietary test systems. A digital multimeter module according to NEP's requirement specification, such as physical size and accuracy should be constructed. The module should be able to measure current, voltage and resistance.The final circuit was based on the chosen analog to digital-converter, Maxim integrated´s Max134, which is the main component of the circuit for this instrument. A circuit diagram and PCB layout were made. The result of this project is a constructed DMM board.

The aim of the thesis is to present a study of what works well and what does not work so well in today?s use of computers in primary care with a special focus on the use of computers in the management of referrals for consultation. In May 2009 a module for electronic consultation referrals was introduced in the computer system Cosmic at the University Hospital in Uppsala. Previously, the primary care units had to use two different systems for management of referrals. Referrals sent internally within primary care have been sent electronically while referrals to the University Hospital or other external units were sent on paper.

A large amount of our time is spent indoors in an artificial climate. To make the experience pleasant there are requirements on the ventilation and the heating system. At the present time the most common form of heating is a radiator system complemented with a ventilation system. A ceiling heating system with combined heating and ventilation can replace the two separated systems. The benefit with a ceiling heating solution is that it saves space since the radiator system is no longer needed.

This thesis deals with the concept of how price affects demand for a good by estimating various price elasticities of demand for snu sold in Sweden. Information was gathered on price development for snus and cigarettes as well as sales data from Swedish Match, the largest supplier of snus in Sweden. Income-, price- and cross-price elasticities were estimated based on log-log regression. Results show that snus is an inelastic good since the coefficient for price of snus was -0.536. This proved that a 1% increase in price causes a 0.536% decrease in quantity demanded.

In today's society it is becoming more and more important with direct marketing. Some of the direct marketing is done through e-mail, in which companies see an easy way to advertise himself. I did this thesis work at WebDoc Systems. They have a product that creates web documents directly in your browser, also called CMS. The CMS has a module for sending mass e-mail, but this module does not function properly and WebDoc Systems customers are dissatisfied with that part of the product.

The project, Flexible Snowboard System, has been carried out by the project group independently and is a module developed for snowboarders, ski rentals and ski schools. The problems of today?s solutions are that they cause the user an inconvenient standing position when riding the ski lift or skating the transportation slope, also mounting, adjustments and disassembling of the bindings are time consuming and brings undesired wear to the screws and screw holes. In addition any adjustments require that the user steps out of the bindings and have tools at hand. Flexible Snowboard System is a universal module which means that it can be assembled with all of today?s snowboards and bindings.

The purpose of this thesis was to create a saw pattern program for the sawmill industry. I have chosen to focus on the module that describes the shrinking on the wood. There are several theories about how the wood deforms by shrinking. Several hypotheses were simulated in the program and after testing them I decided to use only one of them (hypothesis C). The program is written in Visual Basic .NET and I choused that program language because it is easy to do changes in the layout. Another great advantage in Visual .Net is that you can mix different languages in the same program.

Minimizing power consumption is a critical part of many embedded design projects. Thechallenge is to limit the power consumption of the system and at the same time providesatisfactory service to the user. With regards to microprocessors, the main way of limiting powerconsumption during program execution is to adjust the frequency and the voltage at which theprocessor operates.To enable the implementation of real-time scheduling with support for dynamic voltage andfrequency scaling, an exhaustive study of the Freescale i.MX31 embedded microprocessor isperformed. Specifically, the power consumption relationship to all relevant frequency andvoltage settings is investigated. In addition, to enable frequency and voltage scaling in a real-timeenvironment, a complete timing analysis of proposed voltage and frequency scaling methods isperformed and their suitability for use in real-time systems is evaluated.To integrate voltage and frequency scaling capability into OSE RTOS, a software module hasbeen developed for this operating system.

This report describes the planning and the accomplishment of the final diploma workat the study program Mechanical Engineering, Department of Engineering Sciences, Uppsala University. Two students carried out the diploma work at GE HealthcareHusbyborg in Uppsala.The aim of the diploma work was to develop and improve existing processequipment for 11C-radiochemistry in PET. The process equipment was to be dividedinto smaller independent modules to make it more flexible. Part of the existingprocess equipment is an oven that is supposed to perform a specific chemicalreaction. One of the main goals was to study and improve this oven.The work could be divided into three main phases: 1.Present concepts for one module, and interface between different modules.

This report describes the planning and the accomplishment of the final diploma workat the study program Mechanical Engineering, Department of Engineering Sciences, Uppsala University. Two students carried out the diploma work at GE HealthcareHusbyborg in Uppsala.The aim of the diploma work was to develop and improve existing processequipment for 11C-radiochemistry in PET. The process equipment was to be dividedinto smaller independent modules to make it more flexible. Part of the existingprocess equipment is an oven that is supposed to perform a specific chemicalreaction. One of the main goals was to study and improve this oven.The work could be divided into three main phases: 1.Present concepts for one module, and interface between different modules.

The Results of this thesis was the creation of two designed house variants with a module toall the apartments. In addition till the first module there are three other modules ofapartments that can be put in the houses if it so needs. The house are volume prefabricatedand are placed on site in a way that it create an enclosure of the area which faces against thenature and car parks also lies hidden behind these houses.For the actual structure, a cross beam was created to carry the floor above and it is supportby all four walls. The structure between the first and the second floor has no "syll" butinstead there are two differently alternative to linking the floors in order so that it will notmove. The reason with this solution was that there will not be any subsidence when theforces from above are pressed down ward.

To be examined in hospitals can sometimes be perceived aspainful by children. Therefore there is a need for something,which can distract children?s attention from their perceivedpain. During my graduation project, I discovered a designopportunity to work with suspended ceiling systems inexamination rooms, as there is not much to look at whilebeing examined.The result, Twig Ceiling is an interactive nature-inspiredbacklit module with colored LEDs. Twig Ceiling has onelayer of pattern that is visible when the module is not litand the second layer of pattern appears when turning onthe light.

ABB I-R Waterjet Systems combines the robotics and motion expertise of ABB Flexible Automation with high-pressure intensifier/pumping technology from Ingersoll-Rand to provide and continue to develop innovative waterjet cutting systems for global markets. The purpose of this assignment is to develop a process water purifier. The purifier should be applicable as an option to ABB I-R?s production cell Cutting-Box. At first hand the process water should be purified well enough to let out in the municipal sewage system, but the ultimate solution is purifying the process water to the range that recycling is possible.

ABB I-R Waterjet Systems combines the robotics and motion expertise of ABB Flexible Automation with high-pressure intensifier/pumping technology from Ingersoll-Rand to provide and continue to develop innovative waterjet cutting systems for global markets. The purpose of this assignment is to develop a process water purifier. The purifier should be applicable as an option to ABB I-R?s production cell Cutting-Box. At first hand the process water should be purified well enough to let out in the municipal sewage system, but the ultimate solution is purifying the process water to the range that recycling is possible. When investigating the different principle of purifying water, a research of different products and their manufactories was done. These different products were compared and the principle of filtration was the most applicable, as most of the products were designed for far larger applications. As the process water contains quite large amount of particles, it is necessary to perform the filtration in different steps. The process water purifier is therefore composed of a module of coarse filtration and one of micro filtration. In the module of coarse filtration the mainly amount of fibres and particles are eliminated. They are kept back in the container unit with the larger fragments and dumped with these when the container is emptied. In the module of micro filtration the filtration is performed in two steps. In the first step particles larger than 50?m are eliminated, in the second step the micro filter is setting the range of purifying, in this case 10?m.