This Master of Science thesis project handles issues around managing data from the digital tachographsystem. European legislation states that companies must download the data of the digital tachograph systemand store it for at least one year for control purposes. The system stores data on the vehicle unit located inthe driving compartment and on smart cards personal for each driver.Acquiring data from the previous analogue tachograph was done instantaneously since the data wasphysically printed to a circular paper chart when driving. To acquire data from the digital system one mustperform a download from the vehicle unit and later transfer it to some form of backup solution for longterm storage. Data must also be downloaded from the driver smart cards.Download of data from the vehicle unit is the most time consuming task and may take up to 30minutes pervehicle.

A new type of device for measuring thev m& ?rate of fuel sprays from a diesel fuel injector has been developed and the various steps in the development are described. The device works by deflecting all of the sprays from the injector at the same time by using a bell shaped deflector. A load cell consisting of a machined steel part with strain gauges mounted on it measures the resulting force. The shape of the curvature in the deflector bell shape has been evaluated by photographing the flow in a 2D?version of the curve shape.

The Swedish government have a goal that wind turbines shall produce 30 TWh by the year 2020, compared to about 3,5 TWh produced in Sweden during 2010. To minimize the disturbance that wind turbines create the Swedish Environmental Protection Agency has stated a guideline value that noise from wind turbines at nearby residents shouldn?t exceed 40 dBA, at 8 m/s wind speed. With advanced calculation models, like Nord 2000, the emitted sound from future wind turbines can be calculated at an early stage to optimize the power production without exceeding the 40 dBA. When the turbines have been built there is a need to verify that they really are within the guideline.

In the process laboratory of Metso minerals (Sala) AB, continuous tests have been made with a laboratory unit High-Rate thickener. The tests are made in order to compare three methods of thickening techniques of suspended solids. The three techniques are High-Rate thickening, conventional thickening and lamella thickening. The High-Rate and the conventional trials are based on a continuous method, while the lamella thickener is based on batch trials. Because the lamella thickener is based on batch trials and there were some optimization problems with the adding point of the flocculant at the continuous trials, it was not feasible to compare the lamella thickener with the other two thickener types.

In this project the task has been to develop a product that will facilitate an operation for personnel working in a sterilization center. The operation is to steer the front of a loading trolley into the chamber of an autoclave, a so-called docking. The moment is complicated because the margins to deviate from ideal docking position and still succeed, is very small.The principal Getinge's desire was that the product could be retrofitted at the customers on their existing systems. One of the demands was that the product should fit two types of trolleys, one with a adjustable working height and one with a fixed working height. Getinge is supposed to purchase the system from a subcontractor who shall manufacture it and the requirement from Getinge is that the cost of purchase mustn't exceed SEK 500Initially principles, solving the problem was developed.

AbstractDuring recent years the climate in recruiting new personnel has hardened as a result of high levels of employment and increasing competition in labour market. In order to resolve this problem, organisations have to adapt new strategies to attract and meet the demands of potential employees who have the required competence to meet job requirements.The aim of this study has been to examine a well functioning work place in order to elucidate explicit examples of what employees consider positive, and what can be ascertained as positive deviations. Narratives emanating from the unit manager and personnel illustrate their views on the positive influences found in their working place. Another ambition is to increase awareness and understanding about the factors that promote satisfaction in the workplace and positive deviation; and to utilise this knowledge.Traditional research on organisations has frequently focused on problems. The theoretical point of departure of this study is based on Positive Organizational Scholarship, abbreviated as POS.

This report is about helping Q-Med AB in Uppsala to start its implementation of uncertainty of measurements analyses in their manufacturing department. Prior to this, the company relied solely on personal experience or did not take this uncertainty into consideration at all during different kind of measurements, which means that some of the processes that the company previously believed were within specified acceptance limits, will actually fail when considering these sources of uncertainties.Q-Med AB needed some sort of instruction to help the company, in a systematic way, to investigate different types of disorders that are affecting all kinds of measurements. This instruction includes a short summary about measurements and uncertainty of measurements in general and a detailed procedure about how these uncertainties are going to be handled in their daily work.The goal was to be able to use this instruction to systematically locate, eliminate (when possible) and analyze all kinds of disorders when measuring. Q-Med is using a lot of different types of instruments when measuring different types of quantities, including temperature, mass, pressure and density. This instruction will hereafter be used for every instrument, regardless of quantity and type of instrument.The instruction is tested through 4 different kinds of measurements, for mass, temperature and humidity.

The moisture content in 10 deliveries of tree parts and 10 deliveries of wood residues were measured with different methods to analyze the quality of procedure used at Dåvamyran today. At the same time a survey was made on the measure procedures used at heating plants in Sweden The majority of the heating plants in Sweden use weight and moisture content as base for payment but at some plants only volume. The moisture content is usually estimated by drying wood chips in an oven but few plants a visual estimation is used. At few plants moisture content is estimated spectroscopicily. The techniques using near infra read light and other electromagnetic are still at a test stage. The methods of measurement used today are quit unreliable for the individual deliveries and there is a risk for systematic mistakes.

Each year approximately 2,000 new detailed development plans are accepted in Sweden. When an area is covered by a new detailed development plan, it is often necessary that land has to be acquired to adjust the property units to the new plan. The owner conditions of the property units can usually be adjusted through negotiations between the seller and the buyer. But in some situations, when no agreements can be reached, it is possible to use coercive measures to purchase the land. Compulsory purchases are only permitted when certain legal criteria?s are met.

Dementia may cause difficulties in communicating. People suffering from dementia are therefore often described as being unable to take part in meaningful conversation. The responsibility to create understanding in a conversation is shared by all participants. By means of different strategies, participants in conversation can construct understanding through collaboration. How these strategies are utilized in conversation where one or more of the participants suffer from dementia is relatively unknown.

To be allowed to sell Z-suspended vehicles with dipped beam Xenon or LED lighting, Scania have to develop automatic headlight level control. This master?s thesis aims to be the foundation to that development.The thesis consists of several parts; a market analysis of how competitors to Scania and the general vehicle industry solve this problem; several available principles for detecting the amount of control needed; the construction of a test station for sensors, a control unit and components connected controlled by the control unit; a further theoretical and practical development of one principle ? one rotational sensor connected between the chassis and the back drive axis; a state flow model programmed in Simulink that produces the control signal for the headlight leveling from the sensor input.Lastly the thesis gives some recommendations to the further development and implementation of automatic headlight level control on Scania vehicles..

This report is about helping Q-Med AB in Uppsala to start its implementation of uncertainty of measurements analyses in their manufacturing department. Prior to this, the company relied solely on personal experience or did not take this uncertainty into consideration at all during different kind of measurements, which means that some of the processes that the company previously believed were within specified acceptance limits, will actually fail when considering these sources of uncertainties.Q-Med AB needed some sort of instruction to help the company, in a systematic way, to investigate different types of disorders that are affecting all kinds of measurements. This instruction includes a short summary about measurements and uncertainty of measurements in general and a detailed procedure about how these uncertainties are going to be handled in their daily work.The goal was to be able to use this instruction to systematically locate, eliminate (when possible) and analyze all kinds of disorders when measuring. Q-Med is using a lot of different types of instruments when measuring different types of quantities, including temperature, mass, pressure and density. This instruction will hereafter be used for every instrument, regardless of quantity and type of instrument.The instruction is tested through 4 different kinds of measurements, for mass, temperature and humidity.

A method for measuring the total impulse from a multi hole diesel injector, introduced inprevious thesis work, ?Development of a method and a device for measuring the momentumrate of fuel sprays?, by Mikael Lindström, has been further developed and tested. The conceptis to simultaneously deflect all sprays from a multi hole diesel injector by using a bell shapeddeflector. The fuel sprays are deflected straight down from their initial umbrella angle, andthe resulting deflection force is measured in a thin strained section of the load cell. The strainis given by three strain gauges, with quarter-bridge circuitry for each gauge.

Control and comparison of various cleaning methods on restaurants in Södra RoslagenThe purpose of this report is to find out and analyze the efficiency of cleaning methods in restaurant kitchens. The investigation was carried out through unannounced inspections at 89 restaurants in Södra Roslagen (municipality of Danderyd, Täby and Vaxholm). ATP-measuring was done on a plate, a knife, a bench surface and a cutting board. The ATP-method measured the amount of food residue on equipment and working surfaces after cleaning, with a luminometer and swabs. Restaurant staffs were asked to describe in detail how and when the last cleaning was carried out on the surface.

The aim of the study was to gain a deeper understanding of the expectations that assistant nurses in the elderly care have on unit manager's leadership and the consequences if the expectations are not met. To answer the purpose of this paper a qualitative research was conducted with interviews with six assistant nurses in municipal elderly care. To analyze the empirical material communication were used as a theoretical concept. Communication includes codes, signals and messages to be interpreted by the parties in a conversation and they can be both verbal and nonverbal. This means that communication is complicated and can cause confusion if it is interpreted wrong.