Return handling is often regarded as a slow and complex process. Studies have shown that it is not unusual for a return to cost up to nine times as much as a standard outbound delivery. An efficient return handling process is therefore essential to all competitive companies dealing with logistics. This report investigates, analyzes and gives suggestions on development with the purpose to improve the return handling process at LensLogistics AB in Kista, north of Stockholm, Sweden. The study has been conducted from a deliberately practical point of view in order to suggest improvement suggestions possible to implement and thereby change the entire return handling process.

Problem: In society of today corporate competence is an important factor for survivor and development. IT is developing rapidly and can not be ignored by companies. Then need for people with IT-competence is conquent increasing. A survey of corporate IT-competence is therefore of interest for companies as well as for local authorities. To determine the IT competence within an organisation, this competence has to be measurable.

Background:IT development has in recent decades been fast progressing. In Sweden many schools have begun to invest in IT and new technologies. What happens at the schools that are investing in IT equipment and modern technology?Purpose:The purpose of this study is to elucidate the conditions for and the success factors and barriers that principals and teachers will experience in IT. Principals' experiences are complemented and mirrored against the teachers.

The purpose of this study is to increase the understanding of activities, flows and waste in a company's production process. By performing a value stream analysis, non-value adding activities are identified in a production process and then the suggested improvements that can reduce lead times will be stated. The value-stream mapping identifies the flow of information and the flow of material in a production process and this provides the basis for the identification of non-value adding activities.We conducted the study at Lammhults Möbel AB in Lammhult Sweden, where the production flow of Spira-21 has been investigated. This to identify any non-value adding activities that affect the flow negative and consumes time and money in a non-value adding way.A reasonable approach for the project was taken by studying the methodologies and theories. We conducted interviews and site surveys at Lammhults Möbel AB where the flow of information and material in the production process were investigated.

The purpose of this essay is to find out if liming with Ca(OH2) and CaO can reduce leachingof phosphorus from agricultural land and the problem with eutrophication. This purpose alsoincludes getting knowledge about how to make the phosphorus retained in the soil and beaccessible for the plants. This essay is supposed to show if more research is needed in thissubject. There has not been much research about this subject and therefore the amount ofmaterial to study is limited in this literature review. The research reports that have beenstudied have similar results.

The purpose of this assignment at SSAB Tunnplåt in Borlänge was mainly to investigate and describe the circumstances for the spare parts stored in storage facilities within the area of operation. Even new facilities which could serve as storage rooms and their opportunities for storing spare parts were an important part of the investigation. This because of the need for improved storing of spare parts. Furthermore, market offers where reviewed for storage of spare parts in more tailored designs. The work will culminate in proposals for improvement which is of importance for the development surrounding the storage and handling of spare parts.

This thesis investigates lacks in today?s use of the ERP-system Mapaz Affärssystem inthe production planning at Solna Pressgjuteri, and possible improvements. Today thedates calculated by the program to plan the orders are inaccurate and the ordersequence is not optimal, and therefore continuous manual corrections are needed.The approach was to study the program Mapaz to understand how it works, andidentify available parameters for input and output in the different tools offered in theprogram. By studying old lists of planned orders and relevant parameters in Mapaz forindividual orders, production groups, products and operations, the connectionbetween input and output parameters could be understood.Participating in planning meetings and discussions with the company behind theERP-system identified the current usage, desideratum and possibilities with theavailable tools. These were then matched to describe the reasons to the insufficientplanning and form possible actions for improvement.The work has showed poor understanding for the ERP-system and its functions, assome tools intended to assist the planning were not used, and some even usedincorrectly.

AB Sandvik Cormorant?s production unit in Gimo has identified a need to examinethe handling of products between operations with the purpose of generatingproposals of improvement for the product handling.The aim of this project is to study the existing manufacturing process and givesuggestions for improvement. The proposals should reduce the manual handling ofproducts, decrease the risk of damaging the products during the manufacturing andform a basis for increased traceability. Based on a mapping of the manufacturingprocess and the problem description, a specification of requirements has beencomposed.The mapping of the manufacturing process suggests that a change of the currentsystem is required. The company is recommended to decide how the producthandling between operations should be performed as guidelines for the productionteam.

The aim of this study was to compare perceived disability in daily activities, anxiety and depression for patients with chronic pain (>3 month), before and after rehabilitation. Another aim was to examine if there were any correlations between disability in daily activities and the extent of anxiety and depression before and after rehabilitation.For the measurements, Disability Rating Index (DRI) that measures disability in daily activities, and Hospital Anxiety and Depression Scale (HADS) ) which measures the extent of anxiety and depression were used. The study was carried out with 50 patients who had suffered from chronic pain and with the objective to return to work after rehabilitation. Of these, 90 % were female. The measurements were carried out at three measure points; before rehabilitation, seven weeks after rehabilitation and one year after rehabilitation.The main result did not show any statistically significant improvement in ability to perform daily activities.The only significant difference that emerged was an improvement in anxiety seven weeks after rehabilitation compared with before.

Syftet med mitt examensarbete var att få mer kunskap om konkreta material som behandlar multiplikation och division. För att få veta vilka konkreta material som finns att tillgå gjorde jag intervjuer med två lärare som fick beskriva vilka material de använder sig av. Jag valde att observera två elever enskilt då de löste de multiplikations- och divisionsproblem som jag hade designat för studien. Det jag fick ut av undersökning var att det finns många olika material som elever kan arbeta med samt att det är viktigt att de får möjligheten att arbeta med dessa material. Jag kom fram till att lärare bör vara medveten om i vilket område som materialet är bäst tillämpad och att elever behöver använda sig av konkreta material för att lättare förstå uppgiften.

Syftet med examensarbetet är att ta del av förskollärares åsikter om och erfarenheter av materialets betydelse för barns lek och lärande, med fokus på ?smutsigt? material i innemiljön. ?Smutsigt? material är material som kan skapa oordning och kladda ner, t.ex. vatten, sand, lera, färg m.m.

To invent an optimized product is a complicated process. This process is only half of the work. It is equally important to develop a production system that can produce the product in an  efficient and ergonomic way.After several evaluations of conceptual and detailed drawings a final idea has come to light.The idea intends, to the maximum extent, utilize the facility in a more efficient way through moving assembly lines and stations closer to the flock section and the stock for complete products. To make the production better, stations are placed in more logical places given the assignment they are supposed to accomplish. This improves the material flow radically.

This thesis is a feasibility study into how Fresenius Kabi may rationalize their destruction process in regards to cost, recycling, and work environment. The two main objectives are to identify scrap flows and the possibility to improve or replace the equipment that is now carrying out the physical scrapping. The flow has been visualized by a flow chart of the material and communication. A chart of the problem established to visualize where improvements are necessary. Based on the problems proposals are presented on how to improve the flow thru the plant.During analyze of the physical scrapping equipment it was also necessary to take a deeper look at how they are carrying out there work today, how does the procedure look like, working environment and where are the weaknesses.

This thesis work has introduced process orientation at the printing company Color Print Sweden AB. The outcome ofthis work is a survey of the work flow at the prepress department. To visualise the production process at the companya comprehensive mapping of the main process, order-to-delivery, has been made. The work has detected a couple ofcritical elements in the existing process. These elements are the following: initial check of material delivered to the prepressdepartment as well as the control made of the plotter print-out, digital test print and plate.

This report describes an bachelor thesis work which is performed in cooperation with SVIA that develops and sells automation solutions for the manufacturing industry. The thesis purpose was to evaluate the machine FeedLine to find opportunities for improvement in the product?s design that could lead to more standardization and thus improving the efficiency of manufacturing and assembly.Based on these basic issues suggestions for improvements were developed:How can the design of FeedLine be improved to facilitate the assembly?Can more standardization be imposed on FeedLine?s design to enable more stocking of standard components?An initial pre-study was conducted to evaluate FeedLine?s to find opportunities for improvement in its overall design. During the pre-study staff at SVIA and two of its clients was interviewed. Based on information gathered during the interviews and observations by the authors improvements was amendments.