Every year new premises are built in Sweden, and even if they are made as energy efficient as possible, this will not reduce the energy demands, but the rate of the increase of the energy use will be reduced. One type of facility in Sweden that is a major energy user is public baths, and this makes public baths an interesting facility to study more closely. There are around 500 public baths in Sweden and about 75 % of those can be seen as older baths with large need of renovation, and they all require a high level of energy efficiency measures. To show how the energy demand increase or decrease depending on the changes chosen to be made, the simulation application IDA Indoor Climate and Energy was used. Simulations were made and compared for several cases, with two extreme cases as starting points.

The aim with the thesis is to get deeper knowledge in one of the subjects botany, livestock technology or economy. I have chosen to get deeper knowledge in how to store potatoes. How are you going to act to keep the quality on the potato during the storage, with a minimum of weight lost? My aim with this thesis is to get a view over how the potato act in storage space. The storage environment is very important in the storage space.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

In this study the hygienic quality of minced moose meat was examined with regard to the prevalence of different bacteria. The methods used are described in NMKL, "Nordic Method Committee for Food". The results show that the levels of Escherichia coli and coagulase positive staphylococci in the meat are too high. The reason for this might be environmental factors, such as high temperature and humidity during the time when the carcasses are hanging and when the meat is cut up..

To establish good horse welfare there are several factors that need to be considered. One important factor is the environment in which the horses are kept. In Sweden horses are stabled during long periods of time in the cold season and consequently the stable environment is even more important. The most essential environmental factors in a horse stable are ambient temperature, relative humidity (RH) and concentrations of contaminants in the stable air. The air in a horse stable contains dust, noxious gases, moulds and microorganisms which all can contribute to developing respiratory diseases in horses.

Bostadsbolaget Mitthem AB äger 11 tvåvåningshus med lägenheter på Uppsalavägen i Sundsvall. Spårfilmsmätningar har visat på radonhalter över gränsvärden i flertalet lägenheter, vilket också konstaterats bero på markradon. I dagsläget är lägenheterna utrustade med F-ventilation utan värmeåtervinning. I detta arbete utreddes möjligheten att lösa radonproblematiken genom införande av energieffektiv ventilation med värmeåtervinning. En sådan åtgärd kan påverka radonhalten genom förändring av dels luftomsättningen och dels undertrycket inomhus.

Current research shows that the number of door openings during surgery is unjustifiably high. It is the operating room nurses task to ensure a hygienic and aseptic environment throughout the surgery with the goal of minimizing the risk of healthcare associated infection. The study aims to investigate whether the operating room nurse is attentive to the number of door openings during surgery and if the operating room nurse is attentive to the reasons behind the door openings. A pilot study with nine observations was carried out on two smaller hospitals in the region of Västra Götaland. The results showed a significant underestimation of the rated door openings compared with the actual ones.

Examensarbetet som utförts på Institutionen för Maskinteknik vid Blekinge Tekniska Högskola i samarbete med Kockums AB har benämningen ? Upphängningssystem?. Dagens upphängning av rör, ventilationsrör och kabelbanor består av ett antal olika singelupphängningar utan större samordning. Detta har gjort att Kockums AB önskat få fram ett samordnat upphängningssystem som klarar av alla dessa upphängningstyper. Utifrån denna problemställning har vi arbetat oss fram till ett upphängningssystem bestående av ett multisystem och ett flertal singelupphängningar för rör, kabelbanor och ventilation.

Vid projektering idag ställs konstruktören ofta inför valet att projektera för antingen ventilation med konstanta flöden, eller med variabla flöden. Vidare kan även flödena varieras manuellt eller automatiskt. Det konstruktören måste ta hänsyn till är investeringskostnaden, men även potentiella energi- samt kostnadsbesparingar över tid. Många gånger är det svårt att veta hur energianvändningen påverkas av de olika systemvalen varför det är svårt att välja det mest optimala systemet.Detta arbete undersöker livscykelkostnaden, LCC, med nuvärdeskostnaden på en skola i Uppsala med tre olika system, antingen konstant ventilationsflöde, CAV med timer, manuellt styrd variabel ventilation, VAV, eller automatisk VAV med styrning på temperatur och CO2. Huvudanledningen till det är att skolor består av en mängd olika klassrum och lokaler som inte alltid används under skoltiden, risken finns alltså att skolan överventileras med ett traditionellt CAV.

The system tungsten-oxygen has potential of being suitable for decorative coatings since ceramic coatings are often hard and wear resistant, and since modulations in oxygen content or incorporation of small ions could give bright colours. The aim of this report was to investigate the relationship between process parameters and  the properties of the films, with the wear resistance being of special interest.Samples with tungsten to oxygen ratios in the range of 100:0 to 25:75 at% were made using reactive sputter deposition, either with constant gas flow, or gas flow controlled by optical emission of the plasma. The hysteresis of the system, which means that a certain gas flow will cause different pressure and/or target voltage depending on in what way the flow is reached, makes it interesting to control the process where the system makes the steep change from metallic tungsten to ceramic tungsten oxide. This is difficult and thus requires precise control equipment.The samples were analysed using X-ray diffraction, X-ray photoelectron spectroscopy and an empirical wear test suitable for small components like cell phone cover for example, in order to characterize the structure, composition and wear resistance of the coatings. The results could be divided into three groups: (I) tungsten-like, with very low oxygen content; (II) mixed phase and (III) tungsten oxide like, with oxygen content close to 75 at%.

Today, about 15 to 20 percent of Sweden?s total emission of carbon dioxide can be traced to the household sector. By examining apartment blocks in a life cycle perspective, the origin of the carbon dioxide emission has been charted and analyzed. This information has been used to create a computational model that calculates the total emission of carbon dioxide from a specific apartment block. The results from the analyzed apartment blocks indicate that both the use of energy and the emission of carbon dioxide have been reduced since the 1960s. Through the examination of building materials, it is possible to lower the emission of carbon dioxide that origins from the construction phase of an apartment block.

This master thesis in energy optimization was made during the autumn of 2006 at Käppala wastewater treatment plant in Lidingö, Stockholm. A preceding thesis, where all electricity consumption was mapped, showed that the aeration in the biological treatment is the single largest consumer in the plant, and it is therefore of interest to reduce this cost. The oxygen control strategy used at Käppala WWTP is working well from a nutrient removal point of view, but not from an economic one. The last aerobic zones have a very low oxygen consumption during low loading periods which give rise to enhanced dissolved oxygen concentrations with excessive costs and reduced denitrification as a result. But also during periods of normal loading unnecessary high oxygen concentration are sometimes given.By modifying the aeration control strategy three full-scale experiments have been made, with the intention to reduce the air consumption.

Ett arbete om olika ljudnivåer i kycklingstallar under en uppfödningsperiod. Hur ljudet förandras inne i stallet i tackt med att djur och ströbädd växer.

In the field of IT-forensics you may often get to analyze different types of digital devices. One ofthese devices is the GPS navigation system. Nowadays GPS technology is getting more and morepopular and is included more frequently in different types of devices. With this article we want topresent the differenent obstacles and possibilites that a forensic investigator is presented with in thistype of investigation. We will be comparing different software suites and make use of forensic toolssuch as EnCase.The reader should get some understanding of the methods there are for analyzing one of these devicesand what problems that may occur in the investigation process.The article presents how the investigator can use different methods to gain information such as recentroutes, favourite destinations and other information that may be stored on the device.

The purpose of the study was to investigate the use and losses of energy in an existing older building. Another purpose was also to look through various options for heating systems with renewable energy in the building. The aim was to reduce the use and losses of energy. The first step was to study the related electricity bills of the building and also perform measurements and calculations of the building envelope and ventilation. The next step was to find out the possible actions for energy saving by performing measurements and calculations.