This thesis of 15 hp has been implemented at Halmstad University, incollaboration with Saab Dynamics in Linköping. Saab Dynamics is a companyoperating in the defence industry where competition is tough. This necessitatesnew ways to increase efficiency in the company, which is the basis for this thesis.Saab Dynamics wants to introduce simulation driven design. Since SaabDynamics engineers have little experience of simulation, required a usermethodology with clear guidelines. Due to lack of time, they chose to assign thetask to students, which resulted in this thesis.The aim of the thesis is to develop a methodology in mechanical design, wherethe designer uses the FE analysis early in the design process to develop thestructures' mechanical properties.

The exhaust arrangement on a Scania V8 consists of one manifold at each bank connected to a twin entry turbine (8-2-2). A study in GT-Power has shown improved performance and reduced cylinder to cylinder variations using two manifolds at each bank in combination with a single entry turbine (8-4-1). This thesis work analyses the difference in performance shown in simulation and verify it by engine test.The initial work was focused on simulation in GT-Power. Investigating how exhaust manifold volume and pulses effects the turbine efficiency and the mean effective pressure during the gas exchange. To verify GT-Power simulations four engine tests with different exhaust arrangement have been made.The results from GT-Power simulation indicate that a larger exhaust volume improve the turbine efficiency.

Uppsats för avläggande av filosofie kandidatexamen iKulturvård, Landskapsvårdens hantverk, 15 hp, 2013.

Heat and power stations are often in need of optimizations. A simulation model is a tool for findingways to optimize the plant. The scope of this diploma work is to develop a simulation model ofBoiler 5 at Mälarenergi AB. Boiler 5 is a circulated fluidized bed boiler that was taken into service inyear 2001. Among the included parts in the boiler are cyclone, convection part andINTREX-chambers.

Syftet med detta arbete är att diskutera förhållandet mellan historisk spelfilm och historieundervisningen i den svenska skolan idag. Spelfilm har blivit en del av elevers vardag och historiker diskuterar i allt högre grad hur historia används i spelfilmer och hur detta påverkar vårt historiemedvetande. Möjligtvis är det så att detta bruk av historia leder till ett nytt historiemedvetande. Film kan ses som ett pedagogiskt redskap, en upplevelse som leder fram till intresse och kunskap. Vad detta arbete strävar mot är att undersöka om man kan lära sig något om det förflutna genom historisk spelfilm samt om historisk spelfilm kan utveckla elevers historiemedvetande. Arbetet tar sin utgångspunkt i ett projekt om historisk spelfilm genomfört med högstadie- och gymnasieelever på två skånska skolor. Med avstamp i visandet av två filmer om medeltiden; Robin Hood- Prince of Thieves och En riddares historia, diskuteras faktakunskap, förståelse och historiemedvetande..

Examensarbetet syftar till att jämföra nya alternativ till olika system för användning i laborationer i reglerteknikkurser för olika studentkategorier. Det skall utredas vilket av ett antal alternativ till mjukvaruplattformar som är bäst lämpat att användas vid reglerteknikundervisningen i ITN:s reglerlaboratorium vid Linköpings universitet. Tidigare laborationer i berörda kurser skall även modifieras så att dessa kan genomföras i de nya systemen.Examensarbetet resulterade i en rad modifierade laborationer och system att tillämpa i dessa. De nya systemen medför att all reglering sköts direkt från en dator istället för tidigare variant med externa apparater som programmeras. På så sätt kan större fokus läggas på regleringen i sig och inte de system som tillämpas för att utföra den..

This thesis of 15 hp has been implemented at Halmstad University, in collaboration with Saab Dynamics in Linköping. Saab Dynamics is a company operating in the defence industry where competition is tough. This necessitates new ways to increase efficiency in the company, which is the basis for this thesis. Saab Dynamics wants to introduce simulation driven design. Since Saab Dynamics engineers have little experience of simulation, required a user methodology with clear guidelines.

This thesis work contains a litterature study about electrical motors in general and how PWM-patterns for brushless DC-motors can be made. A suitable method has been implemented as a simulation model in VHDL. A simulation model of a brushless DC-motor which describes the phasecurrents, torque and angular velocity has also been made. The motor model made simulations easier for the complete PWM-system. The design was synthesised and tested with a prototypeboard including a SPARTAN II FPGA.

This thesis of 15 hp has been implemented at Halmstad University, incollaboration with Saab Dynamics in Linköping. Saab Dynamics is a companyoperating in the defence industry where competition is tough. This necessitatesnew ways to increase efficiency in the company, which is the basis for this thesis.Saab Dynamics wants to introduce simulation driven design. Since SaabDynamics engineers have little experience of simulation, required a usermethodology with clear guidelines. Due to lack of time, they chose to assign thetask to students, which resulted in this thesis.The aim of the thesis is to develop a methodology in mechanical design, wherethe designer uses the FE analysis early in the design process to develop thestructures' mechanical properties.

Simulation is a vital tool during development of JAS 39 Gripen, since money and time can be saved.The Auxiliary and Emergency Power System, AEPS, is a subsystem of the secondary power system in Gripen. It has the function of providing the aircraft with electrical and hydraulical power before activation and after deactivation of the main engine. The system also functions as backup in case of a safety critical problem in the main power supply system. The system basically consists of a control unit and an auxiliary gearbox. The gearbox is driven by an air turbine.

Fluids are important to the Visual Effects Industry but extremely hard to control and simulate because of the complexity of the governing equations. Fluid solvers can be divided into two categories, those of the Eulerian point of reference and those of the Lagrangian. Both categories have different advantages and weaknesses and hybrid methods are popular. This thesis examines Smoothed Particle Hydrodynamics, a Lagrangian method for physically based uid simulations. To allow the artist the exibility given by shorter simulation times and increased number of iterations, the performance of the solver is key.

In this thesis, the Train Power System Simulator (TPSS) has been compared and verified with the commercial simulator TracFeed® Simulation (TracFeed). The basis for the comparison was a given part of the Swedish railway system, with steel transportation trains. Primarily, emphasis was placed on running time and energy consumption in simulation results. Two transformer systems were analyzed, booster and auto transformers. The high voltage transmission line, parallel to the railroad track, was disconnected in some simulations.

This thesis of 15 hp has been implemented at Halmstad University, in collaboration with Saab Dynamics in Linköping. Saab Dynamics is a company operating in the defence industry where competition is tough. This necessitates new ways to increase efficiency in the company, which is the basis for this thesis. Saab Dynamics wants to introduce simulation driven design. Since Saab Dynamics engineers have little experience of simulation, required a user methodology with clear guidelines.

To give a realistic impression in a driving simulator for nighttime driving, there are many challenging aspects to consider. One of the most important aspects is the illumination caused by the headlights of the own vehicle. To give a realistic impression there is the need to consider the characteristics of the headlight in use to be able to represent main and dipped beam, but also to represent different models and types of headlights. Another important aspect is the dazzling effects caused by the light cast by other vehicles upon the driver. These effects are not only important to give a realistic and visually appealing simulation, but also to simulate blinding effects which may affect the drivers ability to perceive the traffic environment to a large degree.

The topic of this thesis interest is the relation between branding as a place making/marketing technology and the process of regionalization. The main proposition advocated is that the officially communicated image of the Øresund Region, as a cohesive place and community, is a space that has been configured with branding and can be described as a territorial simulation. The concept of territorial simulation consists of two conjoined terms: simulation which aim at explaining the idiosyncratic brand image, as a social formation, which does not represent the place it imitates but commoditise it; and territorial which seeks to visualize the process of the unfolding of this image as a territory. The main argument is made in the third chapter, which traces the process of actualization of the brand image as a territory: ?Øresund?.