The study aims to reduce energy consumption in apartment buildings where individual metering and charging of heat is applied. The aim is to develop planning and design for individual metering and charging in apartment buildings.The study is based on literature review, interviews and case study that include analysis of existing documents. Interviews were carried out with the property developer and the involved consultants who planned the apartment building Yasuragi. To investigate the differences the condominium association has noted in heat consumption between flats, the debit values of the heat were used to discern which houses that were furthest from the average consumption. On these flats there were temperature measurements and thermal photo shoots made for discriminating behavior and possible construction techniques which could be the explanation for the heat spread.Boverket shows that the consumption of heat can be reduced by 10-20% after insertion of individual metering and charging in an apartment block.

För att transportera bränsle från tanken till motorn används på tunga fordon idag vanligen en mekanisk pump, driven av och placerad på motorn. Anledningen till att ha en direktdriven pump är främst att det anses som den mest robusta lösningen för den relativt enkla uppgiften som bränsletransport och liten tryckökning anses vara. För att klara av motorstart och driftsfall med höga bränsleflöden är dagens pump överdimensionerad för det behov som finns större delen av tiden.Önskvärt vore att kunna reglera bränslemängden kontinuerligt, för att minska pumparbetet i de punkter matarpumpen idag har överkapacitet. En elektrisk pump kan regleras att endast pumpa bränsle efter behov och erbjuder även andra fördelar, som t.ex. fri placering, möjlighet att använda en mindre pump och tilläggsfunktioner genom mjukvara, exempelvis priming och automatisk avluftning.Projektet har genomförts i form av en förstudie med konceptgenerering för placering av komponenter och provning av dagens system för kravspecifikation.

För att tillgodose den studerande KTH byggnadens framtida krav kommer det befintliga ventilationssystemet att bytas ut. Två olika möjliga värmeåtervinningssystem har jämförts ur fjärrvärmebehovssynpunkt. Det befintliga systemet med vattenburen batterivärmeväxlare har en låg värmeåtervinningsgrad och Akademiska Hus önskar system med högre värmeåtervinning. I byggnaden har roterande värmeväxlare och frånluftsvärmepump för uppvärmning av tilluften jämförts. Då värmeåtervinning från dessa system inte är tillräckligt kommer fjärrvärme att används.I beräkningarna jämförs fem roterande värmeväxlare mot varierande antal frånluftsvärmepumpen.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

An investigation of the heat impact of laser cutting on the material properties when producing tensile and impact test specimens of different steel types of varying thickness has been performed. The purpose of the thesis project was to provide recommendations regarding how much material that needs to be milled from the laser cut edge before tensile and impact tests. The study has been performed partly by investigating the test specimens by heat camera when the specimens were cut in the laser cutting line and partly by performing hardness tests, investigation by microscopy, and tolerance and roughness measurements and tensile tests of the laser cut material and material produced in the traditional multi operation machine. The results show that the heat affected zone in the thicker materials is greater than previously thought of, and that the currently used recommendation has to be adjusted. The study clearly shows that the thicker the material, the greater the heat affected zone, independently of the steel type, since the thicker material takes longer time to cut.

To achieve the requirements to decrease emissions of greenhouse gases by 20 % by 2020, Swedenneeds to increase its use of bioenergy. In doing so it seems natural that those who already haveaccess to large amounts of biofuels in the form of by-products such as straw, wood chips anddigestible materials take advantage of these assets locally. By combining production of heat withpower production at the farm it may be possible to not only reduce the direct use of fossil fuel forheating but also reduce energy costs.The purpose was to simulate different cases of using a small scale biofueled combined heat andpower plant for farm-based systems. A MatLab-model was developed and used to draw conclusionsabout the costs for production of heat and electricity with different conversion technologies.The model uses climate data to simulate the variations in heat energy demand on a day-to-day basis.The given heat demand is the base of the simulation and from this the possible electric output iscalculated. This study has focused on the impact of the following properties: electric-, heat- andtotal efficiency, fuel, fuel price and specific fuel requirements.

Svensk Växtkraft is the owner of the biogas plant in Västerås. The company is planning to increase their treatment capacity at their biogas plant. In connection to this work it is also possible to make some energy saving changes to the biogas plant. The objective of this study was therefore to make an electricity and heat survey of the biogas plant, a detailed study of the heat consumption in the sanitation step and also a comparison of energy consumption with the present sanitation method and an alternative strategy where the waste is treated in 55 °C during 10 hours (the current method is heating to 70 °C during 1 hour). The energy survey was conducted in close collaboration with staff at the biogas plant. The current during normal operation was measured, power was calculated and multiplied by the time of usage to obtain the energy consumed.

Husums plant has a selection of different pulp pumps at bleaching plant 4 and 5. The displacement- (HC-pump, Sund Defibrator PTD-60) and centrifugalpumps (MC-pump, MCA 42-200, MCP 30/20) are of interest in this report. The centrifugal pumps are controlled by throttle valves, which result in an energy loss. Chemical mixers are used to mix ClO2 into the pulp before proceeding into a holding tower where the bleaching process occurs.The energy demand of the different positions has been measured or calculated to be used in comparisons against new equipment. Quotations were requested and delivered from Valmet and Sulzer.

The purpose of the project has been to work out recommendations that reduce the energy-related costs and environmental impact of HPW Fresh & Dry Ltd., a fruit drying factory in Ghana. The factory produces electricity with diesel and biogas but also purchases electricity from the national electricity company. Heat for the drying process is produced from biogas, kerosene and solar panels. In the project the energy system was analyzed by measuring production and consumption of heat and electricity. The project results show that the factory can become self-sufficient on heat if the available energy is used more efficient. The production units for both electricity and heat have low efficiencies.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

Sapa Heat Transfer is a company that produces aluminum heat-exchanger strips for the automotive industry. Sapa Heat Transfer wish to chart their emissions of carbon dioxide in order to meet future demands on carbon dioxide reporting. They also would like to examine the meaning of the term ?green electricity? which is marketed as carbon dioxide free, and the sort of electricity that they purchase. This report includes both direct (liquefied petroleum gas and diesel) and indirect (water, process-water, long distance heating, waste) emissions from their company.

The study aims to reduce energy consumption in apartment buildings where individual metering and charging of heat is applied. The aim is to develop planning and design for individual metering and charging in apartment buildings.The study is based on literature review, interviews and case study that include analysis of existing documents. Interviews were carried out with the property developer and the involved consultants who planned the apartment building Yasuragi. To investigate the differences the condominium association has noted in heat consumption between flats, the debit values of the heat were used to discern which houses that were furthest from the average consumption. On these flats there were temperature measurements and thermal photo shoots made for discriminating behavior and possible construction techniques which could be the explanation for the heat spread.Boverket shows that the consumption of heat can be reduced by 10-20% after insertion of individual metering and charging in an apartment block.

I was assigned to the thesis as part of a project GMA AB (Ground Machinery Applications AB) is running. The project aims to develop a new method for injection of drilled holes in rock walls. Currently, the injections usually involve cement but the basic idea of the project is to replace cement with a supplement called Silica sol.Silica sol is known as a gelling liquid. The gel time is controlled by a mixing of saline. Depending on the amount saline that gets mixed in, the gel time varies.

The purpose with this thesis is to analyse different factors that can explain district heating prices for energy companies in Sweden. We are further interested in examining if the prices is affected by the use of industrial waste heat in their production and the company?s ownership structure. The method applied is a multiple regression analysis using a panel data set of 50 companies over 5 years (2008-2012). The data used is yearly data obtained from the Swedish district heating association.

Syftet med denna studie var att jämföra två olika smärtbehandlingsmetoder för patienter som genomgår hysterektomi. Försöksgruppen erhöll både PCA pump ( patient ?kontrollerad-analgesi) och sårkatetrar och kontrollgruppen erhöll endast PCA pump. En PCA pump är en förinställd smärtpump där patienten själv sköter sin administrering av smärtlindrade läkemedel. En randomiserad studie utfördes där försöksgruppen bestod av 19 patienter och kontrollgruppen bestod av 20 patienter.