This paper is the result of a case study conducted at Uppåkra Mekaniska AB during the spring of 2006. The task that was presented by Uppåkra was to develop a basis for a decision for the planning activities at the company, so that in the future they can create lot-sizes which are based upon a total cost perspective. Total cost in regards to lot-sizing is defined as the sum of the administrative reordering costs and warehousing cost per stock keeping unit.To collect data a series of interviews and observations were conducted. This data was then used during the lot-sizing simulation and analysis. The 15 units that the simulation was conducted on were grouped into three item classes depending how many different machine setups they required during the production process.

During the last 50 years the production of milk per cow has increased. This has, however, been followed by a decreased reproductive performance. Shorter and more indistinct signs of oestrus make it harder for the Swedish farmers to discover when the cows are in oestrus. There is a need for ways to control reproduction. The use of pheromones could possibly provide means to satisfy this need.

Hydropericardium or pericardial effusion (PE) is the accumulation of fluid in the pericardial sac and is often secondary to pericardial diseases or diseases related to the heart. It is unusual with clinically relevant pericardial diseases in cats but pericardial effusion is the most common one. Since PE causes serious symptoms and may lead to death it is important with a quick diagnosis and treatment. PE can be acute and cause cardiac tamponade, which gives severe clinical signs. Cardiac tamponade needs to be treated immediately or else the cat will die from cardiogenic chock. More common is chronic PE where the fluid accumulates during a longer period of time and the pericardial sac stretches.

As the final course in the education ?University Diploma Programme for Process Operators? there is a thesis in cooperation with a company required.This thesis is about operator maintenance and 5S made at Metsä Board in Husum.In this report you can read my opinions and conclusions based on literature studies and the interviews that have been made with the staff at PM6 (the paper machine).I chose to focus on the theory of lean, 5S and operator maintenance because it covers the area of this thesis.The operators shall do their rounds to make sure that the equipment works fine. They shall also write down things that they notice in a checklist. This is not done as it should be and the question is: can this be solved by using 5S?My conclusion of this thesis are:Better review of the task so that everyone is involved.

The global climate-change means increasing mean-temperature and higher precipitation in Sweden, which leads to shorter periods of frozen ground in the forest. At the same time the harvesting machines are getting bigger and more powerful. The forest industry aim at an even wood flow, and the ground damage has to be as low as possible. The two biggest causes for ground-damage is the bearing capacity of the forest ground and the ground-pressure of the harvesting machines. The aim of this study was to find out some rules for the machine choice considering ground pressure, when harvesting on ground with low bearing capacity.A field study, using a Valmet 890.3 forwarder, was carried out where different ground pressures and their effect on the ground were tested on two different types of ground.Additionally, an inventory of damaged harvesting grounds was made.

This report presents a thesis project conducted by two students at Mälardalens högskola. The project covers 15 points in industrial design and was conducted during April to June 2014. The principal of the thesis works at Plastic Produkter. The assignment was to develop equipment for an effective way to dose, mix silicon, fill a special designed plastic bag and then seal it. The bag is then formed into a breast model.When a customer for various reasons decides to do a breast augmentation or a breast reconstruction, there may be doubt or uncertainty about the result.

AbstractThis bachelor thesis has been assigned by the company ACG Nyström, Borås. ACG Nyström is working in cooperation with a Swiss company named Jentschmann AG. Jentschmann is a manufacturer of ultra sonic welding machines which ACG Nyström is marketing in Scandinavia and the Baltic States. On behalf of Jentschmann AG the company has the aim to introduce the ultra sonic welding technique to new companies.The aim of this thesis is to compare traditional sewing machines with ultra sonic welding machines within two textile areas, protective clothing and outdoor living.Two investigative questions have been formulated for this purpose: what are the differences between a sewing machine and an ultra sonic welding machine? Is it possible to replace the sewing technology with ultra sonic welding? These stand as guidance for this paper.To gather knowledge interviews, literature studies, and tests on two different ultra sonic welding machines were performed.

Buffer zones play an important role for the water quality in our watercourses. When harvesting a forest close to a watercourse a buffer zone should be left. When it's not left, it will lead to radical changes in the environment for the water organisms. The overall purpose of this thesis was to illuminate the production- and environmental thinking when establishing new buffer zones in south of Värmland. The partials goals were to determine choice of tree species, ways of regenerate, occurrence of soil scarification and the occurrence of machine tracks in newly established buffer zones.

This report examines the industrialization of a newly developed household machine on behalf of Technogarden Engineering Resources in Karlstad, Sweden. The report is a part of the final course in the Bachelor Program in Mechanical Engineering at Karlstad University and takes place in spring 2014.An innovator, an investor and a engineering consultant firm have through collaboration developed a new type of gruel machine. The product is in its final stage of construction and is planned to be manufactured in a production located in Sweden, autumn of 2014.To compete against today?s trend in outsourcing manufacturing to low cost countries for better profitability, the industrialization of the gruel machine must be done with a minimum amount of resources in order to become successful, which also describes the problem of this study. Using pre-study material in form of Lean production literature, visiting a successful production site and gathering data from involved engineers a specification was developed which describes what this industrialization must achieve and which requests can be accomplished.

Sport horses are widely used for performance in jumping, dressage, endurance etc. To enable comparisons of horses, training facilities, programs or physical status, an exercise test can be used. Exercise tests are also important to increase knowledge about exercise physiology of the horse considering different ways of training to compare training methods or individual qualities, development of an individual or other investigations of equine exercise physiology. Since several investigations are done on standard- and thoroughbred horses but less on sport horses, it is of great importance to get an overview of the investigations done. Most common is to investigate heart rate and lactate concentration.

Hydropericardium or pericardial effusion (PE) is the accumulation of fluid in the pericardial sac and is often secondary to pericardial diseases or diseases related to the heart. It is unusual with clinically relevant pericardial diseases in cats but pericardial effusion is the most common one. Since PE causes serious symptoms and may lead to death it is important with a quick diagnosis and treatment. PE can be acute and cause cardiac tamponade, which gives severe clinical signs. Cardiac tamponade needs to be treated immediately or else the cat will die from cardiogenic chock. More common is chronic PE where the fluid accumulates during a longer period of time and the pericardial sac stretches.

Chronic valvular disease (CVD) is the most common cardiac disease in dogs, which account for 75% of all the cardiac cases. Cavalier King Charles spaniel (CKCS) is the most affected breed and it´s 13th times more likely that a CKCS, between the age of 7-10 years, will die or be euthanized for cardiac disease, compared with other breeds. The prevalence has been proven to bee independent of coat color and weight but highly dependent on age and gender in CKCS. In 2001 the Swedish Kennelclub and the Special club for cavalier King Charles spaniel created a breeding program against CVD in CKCS. In this program dogs are not allowed to breed until 4 years of age and have to have a heart auscultation without murmurs.

The aim of these two studies was to investigate the possible physiological, behavioural and emotional changes that appear after human-horse interactions and also to find an explanation to why they occur. One aspect that is discussed is whether the wellbeing of humans can be coupled to interacting with horses and of how the animals respond to the interaction. The first study was performed on 9 horses and their owners, both parts being subjects to registrations during 4 different interaction treatments. The second study was performed on 6 horses with registrations only being performed on the horses during 2 different treatments. Nine horses underwent 3 different treatments all performed by their owners (H = stroking of the horses forehead, B = brushing and M = stimulation of the withers) in addition to a control round (K). Each treatment lasted for 4 minutes but observations were performed until after 45 minutes from start.

GPS (Global Positioning system) and GIS (Geographical information system) has been used for planning and inventory in the forest sector for more than ten years. The last years the development has come to equip harvesters and forwarders with GPS and GIS (GIT). The goal with this study was to reach a basis for decision, how Stora Enso Skog should continue its investment in GPS and GIS in harvesters and forwarders. To reach this basis for decision, possible advantages and benefits, disadvantages and problems in the harvesting process was evaluated. The study was made as an interview study with four harvesting managers and ten machine teams. To secure the quality of the results an interview questionnaire was made before the interviews were done. The results showed that GIT will make the harvesting managers work easier.

This essay serves to illustrate the main practical differences between the popular medium-level programming language C++ (C Plus Plus), and the newer high-level language C# (C Sharp). It will focus on the aspects that are readily apparent to the application programmer, such as differing syntax, constraints and capabilities.It will also feature a similar comparison between the open source OpenGL graphics library, and the proprietary Direct3D graphics library owned by Microsoft Corporation.It will not go into the differences in ?under the hood? mechanics that the application programmer seldom have to consider after having chosen his programming language or graphics API, such as C# being compiled into an intermediate language and is run on a virtual machine where C++ is compiled directly to machine code, or the differing principles of rendering in OpenGL and Direct3D.This is by no means comprehensive, many things have been left out or overlooked..