Beans are a global source of plant-based protein, and in some countries, they constitute a primary source of protein intake. With ongoing climate change, including rising temperatures, it is necessary to adapt beans to ensure a reliable food supply. An important mechanism that many plants have, to cope with high temperatures, is cooling through transpiration. During transpiration, stomata open and release water vapor. Water molecules use heat energy from the leaf to convert into gas, thereby cooling the leaf.

The purpose of this project is to analyze earthing systems for houses. By practical measurements and theoretical analyzes consequences of possible faults, that can occur within the facility and in the low-voltage distribution network, is illustrated.  The reason for this project is that nowadays one has to arrange with a main equipotential bonding system for buildings. Apart from that, if necessary, bathrooms must be provided with a supplementary equipotential bonding system.The practical measurements verify that potential differences in facilities may be due to voltage drops in the PEN conductor between the origin of the electrical installation and the power transformer.Based on the theoretical analyzes of possible faults, it is considered that the requirement for  supplementary equipotential bonding systems for bathrooms in most cases can be questioned, when basic insulation, fault protection, residual current devise and main equipotential bonding system already provides an adequate level of protection.A PEN conductor loss may result in a situation where metallic parts attached to the equipotential bonding system starts working as earth electrodes. Equipotential bonding system may also increase the incidence of stray currents. If TN-C-S systems is provided with a local connection to earth a redundant system against PEN conductor loss is obtained.

The construction industries are relatively conservative type of business that takes a longtime to adjust for new methods and embrace new ideas. It dose not matter if the newmethod seems to be an improved method as long as it is new and untried. Constructioncompanies are reluctant to change form a longtime working method to a relativelyunknown method.The purpose with our report is to perform an evaluation of BeWi construction method.Our goal are to present the generally opinion about BeWi from the contractors that hasbeen in contact/worked with the method. We also want to know from the contractor?spoint of view if BeWi and the method measure up to the standards that are presented byBeWi and if they believe that improvements need to be done.Our progress up to the final report has consisted of three parts[1]Field studies[2]Interviews[3]Literary studiesWe started out with field studies where we took notes and observed all the includedworking phases on the construction site when using the BeWi method.

This is a study on the outcome of the Swedish Forest Agency´s mission to provide individual advice to private land owners about precommercial thinning. The study was conducted in Sala municipality and included forest owners that had received private individual advice from a Swedish Forest Agency consultant as well as forest owners that had not received individual advice. One of the central issues was to make comparisons between these two groups. The survey was carried out by telephone interviews combined with a smaller field study. The questions were designed to provide information about to what degree the forest owners had been affected by the advice and if there had been a change in the way in which precommercial thinning was performed. In terms of the amount of precommercial thinning that had been carried out, no statistically significant differences were found between the two groups.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.

Texture is an important soil property and accurate particle size analysis of soil texture is therefore crucial. There are a number of well-established and newly developed methods available for determining soil texture. In order to compare the results of these methods, the differences between them must be determined. The difficulties, problems and differences regarding texture class determination were examined through a study performed on forest soil samples. The study compared different methods (pipette, hydrometer and field methods) and two types of dispersing agents (sodium pyrophosphate and sodium hexametaphosphate (calgon)) commonly used for particle size analysis.

This report describes an investigation of the indoor climate in two different workspaces. Since we a big part of our lives are staying indoors in artificial environments, and more particularly in our workplaces, we think it would be interesting to do this investigation. The technical solutions for air treatment systems began with simple natural systems without fans and where the thermal rise of the air applied. In modern time is technical air treating systems used to take care of the fresh air supply. This type of units can supply filtered air with the right temperature to the building. Well-functioning ventilation is essential to bring clean fresh air to the room and effectively remove impurities without sound- or draught problems. The indoor climate is relevant for the output capacity.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.

The purpose of our essay is to develop an understanding and an insight for the fashion industry. We want to examine what the creative industries can learn from the unique position that fashion hold in a field between commercialization and art. We used a theoretical ground to enlarge our understanding for the distinctive place that fashion holds. To gain further insight in the fashion industry we complete the theory with empirical facts. The empirical facts were collected through a qualitative method with deep-going interviews.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.

Background: The project controller is a function witch evolved due to the strong gaining ground of project operation. Why the area of the project controller is interesting to study is explained by the fact that increasing knowledge of this function is important in order to make project operation work well. The fact that opinions in this field disagree, further increases the interest of the field. In order to study the function of the project controller three companies have been singled out. They are IFS, Intentia and Saab Bofors Dynamics.

There have been, in some rare cases, difficulties with clamping of inserts with U-holesin their tool holder. According to the complaints, the inserts could not be properlyclamped or could fracture when clamped. A study has shown that variations inclamping behaviour are mainly depending by the position of the screw hole in the toolholder and the centering of the screw hole in the insert.The focus of this project has been the centering of screw hole in insert. It has beenshown that the screw holes are not always enough centered in the insert. Theproblem may occur after a certain step in the production, i.e.