AbstractEmbla 5 is an office building which has done a large improvement. The clients of this building has made an order of WSP and the student Anders Kempe to calculate the use of energy for the building, and after that result proposing further measures which can decrease the energy use of Embla 5.The ground for this report is when calculation of the present energy use of the building is stated. To make that information of a number of parameters such as envelope, the heating system and ventilation has been located and set in to the simulation program IDA ICE which calculate the energy use.To improve the energy use further this project has been concentrated to change the system of ventilation. Today the ventilation system is of the kind CAV (constant air volume) and the air flow is dimensioned for after recommendations from BBR and Arbetsmiljöverket in the office spaces. Consider that Embla 5  is an office building where the people only staying for 8-10 hours/day so was the ide to see how much energy saving if the air flow is reduced the time people not being in the building.

AimThe specific questions in the theoretic part were:What is contained in the terms "balance and balance skill" and how can this skill be measured?The specific questions in the empirical part were:How does balance skill in different age categories of children correlate with biological and physiological parameters such as age, gender, body height, weight and level of physical activity?MethodsLiterature search based on books and scientific papers related to the questions posed above. Selection was made at libraries and on?line through "Pubmed". Specific search words were used.

A piezoelectric injector was modeled, in this Master Thesis Project which was carried out at Scania CV AB in Södertälje, in GT-Fuel. GT-Fuel is simulation program from Gamma Technology.The simulation model for the piezo injector was divided into a hydro-mechanical system and an electrical system (Piezoelectric element). First the hydro-mechanic model was duplicated from Advance Continuous Simulation Language model (ACSL). The simulation results were then compared to the ACSL, to verify that the hydro-mechanical system was modeled correctly. The simulation results for the electrical model were also compared with a Simulink model.

The system tungsten-oxygen has potential of being suitable for decorative coatings since ceramic coatings are often hard and wear resistant, and since modulations in oxygen content or incorporation of small ions could give bright colours. The aim of this report was to investigate the relationship between process parameters and  the properties of the films, with the wear resistance being of special interest.Samples with tungsten to oxygen ratios in the range of 100:0 to 25:75 at% were made using reactive sputter deposition, either with constant gas flow, or gas flow controlled by optical emission of the plasma. The hysteresis of the system, which means that a certain gas flow will cause different pressure and/or target voltage depending on in what way the flow is reached, makes it interesting to control the process where the system makes the steep change from metallic tungsten to ceramic tungsten oxide. This is difficult and thus requires precise control equipment.The samples were analysed using X-ray diffraction, X-ray photoelectron spectroscopy and an empirical wear test suitable for small components like cell phone cover for example, in order to characterize the structure, composition and wear resistance of the coatings. The results could be divided into three groups: (I) tungsten-like, with very low oxygen content; (II) mixed phase and (III) tungsten oxide like, with oxygen content close to 75 at%.

Information stored on unprotected computers that gets lost or stolen, and falls intothe wrong hands, can easily be accessed by moving the hard disk to a controlledcomputer, or by booting the computer from a removable medium, in order to getaround the operating system login. This is something that largely affects companieswhere customer information, trade secrets and other sensitive information can becompromised. A classic solution to the problem is encryption of individual files, but ithas some drawbacks as it puts a great responsibility on the users and unencryptedinformation can be left by mistake. A better solution to the problem is transparentencryption of the entire hard disk, i.e. that encryption and decryption of informationis performed automatically and without the user being affected.

Automatic rumination measuring can be applied as a health indicator in dairy farming but is also highly desirable for research purposes. This study aimed to validate the technical functionality of the product RuminActTM, which employ acoustics to monitor rumination duration. The time budget of high yielding cows was studied and possible differences in rumination time between 13 rations were interpreted. Further the study examined what affects daily rumination and rumination efficiency. The validation was performed with direct observations that were compared to the automatically recorded rumination durations.

Many watersheds have lost stocks of migrating fish species because of the development of hydroelectric plants and other fragmenting barriers. The remaining stocks of migrating Atlantic salmon (Salmo salar) and brown trout (Salmo trutta) in River Klarälven, Sweden are five times smaller compared to one hundred years ago. A fish-trap at the hydroelectric plant in Forshaga has been vital for the continued existence of the stocks. This is the first hydroelectric plant of eight, blocking the way to the spawning grounds. Spawners are collected in the trap for both hatchery and transport by truck upstream and past seven more hydroelectric plants to the spawning grounds, where they are released for possible natural reproduction.

In this paper, the legal situation regarding freedom of expression versus the duty of loyalty is investigated, this in a context where an employee makes critical statements about his employer through social media.The duty of loyalty is a part of all employment relationships and it follows implicit from the contract regardless of whether it is specified in it or not. This duty means that an employee is required to put the employer's interests before his own and avoid all situations that end up in collision of the duties. The employee may no t either act in such a way that is intended to harm the employer. This means that the employee must be even off duty careful not to appear disloyal to the employer. This may lead to that a status update on Facebook, even when made on the employee's free time, can be regarded as disloyal conduct, with the dismissal or disciplinary action as a result.Case law states that the point of departure regarding criticizing the employer must be that the employee has an extensive such a possibility to that, without that being considered as disloyal conduct.

This master thesis has been done in cooperation with Sweco Viak AB in Sundsvall. The aimwith the project is to investigate the purifying effect of percolation filter due to iron andmanganese. The overall goal was to investigate how the parameters surface load,sandfractions, and burden time affect the purifying effect. The expectation is to optimize thedesign and find a demouldning of the filter that gives sufficient purifying with a highersurface load. As an attempt to accelerate the curing of the filter, experiments with a layer ofsand which surface has been covered with manganese ore (MnO2) on top of the filter havebeen done.As test filters 10 L bars were used and the experimental work was performed at thewaterworks in Hassela and Munkbysjön.In Hassela different sandfractions were tested.

This thesis is based upon the work done at Westinghouse electric company (WEC)inVästerås during the spring semester of 2015 and describes the development of a quickcoupler with associated blade changing tool. These are meant to be used togetherwith a sawing tool that the company uses for the dismantling of nuclear reactors,which is performed under water.The aim of the thesis was to develop a complete manufacturing documentation withdrawings and related CAD models which Westinghouse later can use to manufacturethe tool and the quick coupler. It was also included in the assignment to, if necessary,modify parts of the saw tool to adapt these to the intended blade changing tool.A number of visits to the company's workshop was made during the time to study thesaw that the thesis is based upon. The purpose of these visits was to get a better ideaof the dimensions, construction and the field of use of the saw. On three of thoseoccasions various engineers and consultants accompanied us to discuss possibleproblems with different ideas.This was interspersed with information in the form of literature studies on quickcouplers to create a clearer picture of the nature of the task.When enough information had been gathered a functional analysis was made to dividethe main problem into subthis phase the idea and concept generating process took place.The methods used for this was mainly brain writing and brainstorming.

Due to human influences on the climate an increase in Earth's mean temperature is today an accepted conception. With a rising temperature discussions have started how the climate in an area will change in the future. Equally interesting and important is it also to study the precipitation in an area. Precipitation is the factor, next to temperature, that affects most how a climate in an area looks like and feels. Since precipitation is connected to evaporation the latter parameter is also of interest to study.

Objective: In recent years there has been an increasing interest within the clinical (medical) science in measuring people?s health. When estimating quality of life, present practise is to use the EQ-5D questionnaire and an index which weighs the different questions. The question is what happens if the individuals estimate there own health, would it differ from the public preferences? The aim is to make a new prediction model based on the opinion of patients and compare it to the present model based on public preferences.Method: A sample of 362 patients with unstable coronary artery disease from the Frisc II trial, valued their quality of life in the acute phase and after 3, 6 and 12 months.

ABSTRACT Introduction: One of the great difficulties that the nurse anesthetist encounter in their profession is to assess and estimate sleep depth versus signs of pain in the anesthetized patient. Based on a pre-operative appointment and the perioperative monitoring, an assessment of the patient is made. The experience that the nurse anesthetist has can make it easier to understand what subtile signs of the patient depends on. Purpose: With this in mind, the purpose of the pilot study was to try to find out if there are specific signs of pain during anesthesia and if the professional experience played a role. As a subsidiary aim the authors examined whether there were factors in the patient that the nurse anesthetist takes into account in the identification of pain during anesthesia.

At SLU, Divison of Reproduction, Dept of Clinical Science, there is an ongoing project on the development and evaluation of new methods for the assessment of stallion semen quality. This EEF-study, which is a part of that larger project, has focused on the effects on motility and fertility of stallion semen of two different extenders and selection. Both an objective method and a subjective method for analysis have been used and compared in the study. The increase in the use of artificial insemination with cooled semen in Swedish horse breeding over the last decade is thought to play a part in declining foaling rates (Kareskoski et al, 2006, Kuisma et al, 2006). This calls for better evaluation methods of semen quality since cooling and transportation put higher demands on semen quality in order to maintain fertility (Aurich, 2005).

The interest in small-scale electricity in Sweden has increased strongly in recent years. The interest is noticeable both among politicians to increase the share of renewables in the energy mix, and among electricity consumers to partially replace purchased electricity with self-produced. This has resulted in a significant increase of electricity production in low voltage grids in recent years, and the trend appears to continue in the coming years. The majority of the new production plants are solar cells, followed by wind turbines, and it is also in these the greatest efforts are made in this paper.Distributed generation is often seen as something positive since it will contribute to reduced transmission losses and reduced voltage drop in the networks, and that it increases the share of electricity from renewable sources. In cases where the grids are not strong enough, or in other ways not adapted to manage the installed production, power quality may be adversely affected.