This report discusses a method to detect divers in harbour environments usingpassive acoustic detection. The goal was to achieve as high detection as possiblewithout having too high false alarm rate. A short execution time was also desirable.By using the characteristic of an inhalation a band-pass filter was applied to the signalto improve the signal to noise ratio. After the filtering an energy estimation of thesignal was made. This energy estimation was later used in a frequency analysis, whichcould tell us if there were enough energy in the frequencies that correspond to adivers breathing frequency.

The division of Engineering Materials at Linköping University, department of Management and Engineering, conducted a research project concerning Fatigue life of thermal barrier coatings during 2009. During this project equipment to provoke these fatigue failure by rapidly heating and cooling test subjects in cycles, was ordered.Design and manufacturing of the equipment was handled internally at LIU.The equipment was built using a furnace that is lowered and raised over the table where the test subject is placed. To keep the temperature of the furnace a lid slides in place to close the downward facing opening of the furnace when it is in the raised position. On this door there is nozzle that is used to cooling of the test subject by air.To make sure that the equipment can work independently you need an automation controller that can evaluate if movement can occur without danger of collisions. The control system also needs to monitor that all elements are performed according to plan.This degree project is based on a modular system from OPTO 22 and includes the configuration of a PLC that will be supplied with logic and a user interface.The degree project resulted in a graphic interface in which a user can set desired values for different parameters and get information about current values for them.

The main purpose of this bachelor thesis is to create a product in the form of a database that can be used for cost estimates of equipment within bio refineries. Through interviews and literature searches the key components and their costs were identified. The database was constructed in Microsoft Excel with different tabs for different categories of components; these tabs are further divided into three parts: one part with costs, one part with calculations and an information part. Most of the part with costs contains the expenses found in scientific papers during the literature study, the calculating part converts different capacities according to user preferences and the currency to euro (?) from 2010 and the information part consists of references and information about what is included in the cost.The database is a good tool for making cost estimates for bio refineries.

The main purpose of this bachelor thesis is to create a product in the form of a database that can be used for cost estimates of equipment within bio refineries. Through interviews and literature searches the key components and their costs were identified. The database was constructed in Microsoft Excel with different tabs for different categories of components; these tabs are further divided into three parts: one part with costs, one part with calculations and an information part. Most of the part with costs contains the expenses found in scientific papers during the literature study, the calculating part converts different capacities according to user preferences and the currency to euro (?) from 2010 and the information part consists of references and information about what is included in the cost.The database is a good tool for making cost estimates for bio refineries.

The main purpose of this bachelor thesis is to create a product in the form of a database that can be used for cost estimates of equipment within bio refineries. Through interviews and literature searches the key components and their costs were identified. The database was constructed in Microsoft Excel with different tabs for different categories of components; these tabs are further divided into three parts: one part with costs, one part with calculations and an information part. Most of the part with costs contains the expenses found in scientific papers during the literature study, the calculating part converts different capacities according to user preferences and the currency to euro (?) from 2010 and the information part consists of references and information about what is included in the cost.The database is a good tool for making cost estimates for bio refineries.

The main purpose of this bachelor thesis is to create a product in the form of a database that can be used for cost estimates of equipment within bio refineries. Through interviews and literature searches the key components and their costs were identified. The database was constructed in Microsoft Excel with different tabs for different categories of components; these tabs are further divided into three parts: one part with costs, one part with calculations and an information part. Most of the part with costs contains the expenses found in scientific papers during the literature study, the calculating part converts different capacities according to user preferences and the currency to euro (?) from 2010 and the information part consists of references and information about what is included in the cost.The database is a good tool for making cost estimates for bio refineries.

The main purpose of this bachelor thesis is to create a product in the form of a database that can be used for cost estimates of equipment within bio refineries. Through interviews and literature searches the key components and their costs were identified. The database was constructed in Microsoft Excel with different tabs for different categories of components; these tabs are further divided into three parts: one part with costs, one part with calculations and an information part. Most of the part with costs contains the expenses found in scientific papers during the literature study, the calculating part converts different capacities according to user preferences and the currency to euro (?) from 2010 and the information part consists of references and information about what is included in the cost.The database is a good tool for making cost estimates for bio refineries.

I denna rapport har det utförts två fallstudier från två olika vindkraftsanläggningar och med hjälp av en utarbetad modell har livscykelkostnaderna jämförts för de två fallstudierna.Resultatet visade att livscykelkostnaden per producerad kWh sjunker allteftersom den installerade effekten blir högre.Kostnadsmodellen som utarbetats och tillämpats för resultaten har visat sig ha hög verifierbarhet då resultaten har varit jämförbara med litterära studier..

The purpose with this examination is to build a measureequipment to AerotechTelub AB (AT), who will registrate fault in SRAM-memory in contact with cosmic radiation. The equipment will be created around developcard from Memec Design with FPGA from Xilinx. The logic in the FPGA will be implemented with the hardwaredescribed language VHDL. The SRAM-memory that will be tested is build in CMOS-teknologi. The memorycells will be loaded with a predecided bitpattern.

A new type of device for measuring thev m& ?rate of fuel sprays from a diesel fuel injector has been developed and the various steps in the development are described. The device works by deflecting all of the sprays from the injector at the same time by using a bell shaped deflector. A load cell consisting of a machined steel part with strain gauges mounted on it measures the resulting force. The shape of the curvature in the deflector bell shape has been evaluated by photographing the flow in a 2D?version of the curve shape.

This report discusses a method to detect divers in harbour environments usingpassive acoustic detection. The goal was to achieve as high detection as possiblewithout having too high false alarm rate. A short execution time was also desirable.By using the characteristic of an inhalation a band-pass filter was applied to the signalto improve the signal to noise ratio. After the filtering an energy estimation of thesignal was made. This energy estimation was later used in a frequency analysis, whichcould tell us if there were enough energy in the frequencies that correspond to adivers breathing frequency.

Bakgrund: Produktutvecklingsprocessen har på senare tid kommit att ses som en strategisk aktivitet som är avgörande för företagets överlevnad eftersom produktens utförande och kostnader till stor del fastställs innan tillverkning påbörjas. ?Target Costing? har sitt ursprung från Toyota i Japan och är en metod för strategisk kostnadsstyrning som har vuxit fram för att tidigt styra kostnader. Metoden används för att integrera kostnadsstyrning i produktutvecklingsprocessen i samstämmighet med kundkrav och företagets egna vinstkrav.Syfte: Syftet med studien är att beskriva och analysera hur ?Target Costing? används i produktutvecklingsprocessen på Volvo Construction Equipment i Braås för att ge kunskap till nya potentiella användare.

When I got the opportunity to write this examination did I want to write about something that I both was interest in and also can use in the future. I think it?s going to be difficult to carry on the milk production with only 28 cows. I wanted to investigate the possibility to increase the herd of cows. I also wanted to compare this cost with a new cow house the cows where milked with a robot.

The purpose of this thesis is to analyse and propose improvements to the cost accounting system in use at an airline operating on the Swedish market. The choice of study object is based on the airline?s desire to have its cost accounting system evaluated. During the analysis we have identified a number of points where the current cost accounting system does not correspond to its intended purpose. These points include significant groups of costs not being considered in the current system, potential over capacity is not visible and logic connections between distribution keys and the use of resources are sometimes lacking.

The valuation of an asset is one of the most important thing with accounting, though one of the most difficult thing as well. However, in deciding useful service life for an intangible asset and property, plant and equipment, there are quite a margin for the companies, which creates a difference between companies and industries. When computing the value of the inventories there are a few possibilities available for the companies, which also can generate differencesbetween companies and industries. Although these differences can occur, there might be some similarities in the companies? estimates.