As IT service departments in organisations are becoming more complex and customised, the indirect costs are increasing in relation to the total costs. The difficulty of fully estimating and identifying the spread of the cost in the IT service department is increasing. As a result, firms tend to budget the business unit as a total cost rather than as a spread of defined costs. In order to deal with this challenge an ABC calculation will be applied. The Time Driven ABC model will be conducted in OMX´s Servicedesk unit within the IT services.

This report is based on a thesis that was carried out during spring 2012. The report covers the development of a preliminary study to Performance Sk8. The purpose of the study is to facilitate and contribute inspiration to Performance Sk8 to run an automation project to bring home their production to Sweden from China. The reason is to gain a greater ability to control quality, produce smaller batches and reduce the cycle time to reduce costs.The goal is that the preliminary study shall meet the requirements and wishes Performance Sk8 and other partners defined. The pre study will contain different cost proposals for the automation of selected process and serve as a basis for procurement of the equipment.The pre study has resulted in some proposed solutions to the various steps required to automate Performance Sk8 ?s production.

Radio Frequency Identification, RFID, is a convenient way to enable contactless identification which does not require any physical nor optical contact. As with any radio-based communication the signal can be intercepted, thus making the technology vulnerable to several kinds of attacks. Interception of communication is not the only threat. Since RFID tags might contain personal information or information that will grant the owner access to secure areas, skimming and spoofing attacks are also major threats against this technology. In this thesis report,  the perspective of an adversary is portrayed in an RFID-enabled environment by presenting where RFID is used and how it could be abused.

Today?s wind power plants are only compensated for their reactive power consumption at no-load. As the wind power plants grow bigger the amount of reactive power they need also increases. This is no longer a problem that can be ignored, especially as the net owners are beginning to charge the reactive power they transport.In this thesis a couple of different methods of compensation and their prices will be discussed and evaluated. Problems, such as self-excitation, that can occur if one fully compensates the wind power plant will also be brought to surface.

Radio Frequency Identification, RFID, is a convenient way to enable contactless identification which does not require any physical nor optical contact. As with any radio-based communication the signal can be intercepted, thus making the technology vulnerable to several kinds of attacks. Interception of communication is not the only threat. Since RFID tags might contain personal information or information that will grant the owner access to secure areas, skimming and spoofing attacks are also major threats against this technology. In this thesis report,  the perspective of an adversary is portrayed in an RFID-enabled environment by presenting where RFID is used and how it could be abused.

Sveaverken is a company who manufactures products and equipment for the modern farm enterprise within grain, pork and horse businesses. A large share of Sveaverken's turnover depends on the role as a subcontractor for Delaval within the areas ventilation, manure handling and feeding systems. Sveaverken wants to investigate the possibility to increase sales by establishing new sales channels, for example e-commerce This thesis is an analysis of the Swedish farmers use of internet, attitudes towards e-commerce and Sveaverken's interest within this area. There is also a minor economic analysis of the cost of establishing the e-commerce site. The study focuses on farmers who are potential customers to Sveaverken within Sweden. To examine the farmers opinions about internet and e-commerce a questionnaire was developed and sent out in November 2006, to 500 farmers of which 45% answered. The results show that the average age of the farmers was 42,5 years.

Syftet med studien var att undersöka huruvida utsattheten för ?sunk cost-effect? och förankringseffekten ökade vid intuitivt processande jämfört med analytiskt processande. Deltagarna i studien var 78 studedenter vid psykologiska institutionen vid Göteborgs Universitet. Datainsamlingen gjordes genom en pappersenkät. En 2 × 2 - vägs ANOVA avseende bias och process gjordes för både ?sunk cost effect? och förankringseffekten i en mellanindividdesign.

Today?s wind power plants are only compensated for their reactive power consumption at no-load. As the wind power plants grow bigger the amount of reactive power they need also increases. This is no longer a problem that can be ignored, especially as the net owners are beginning to charge the reactive power they transport.In this thesis a couple of different methods of compensation and their prices will be discussed and evaluated. Problems, such as self-excitation, that can occur if one fully compensates the wind power plant will also be brought to surface.

Traditionally, mining has been performed mechanically with implementation ofyesterdays (and older) data. Several mining companies have started to useautonomous technology and robotics in the production areas although the harshmining environments make it unsuitable for today's electronic equipment. Despite allthe obstacles along the way of digitization, there seems to be no end in sight as thisdevelopment continues. This thesis focuses on what the mining industry is aiming forand why the mining companies are interested in these technologies. The actors of themining industry can be found to have a vision for the future mine, a production with ahigher degree of digitization and resemblances to a factory.

This thesis work has been carried out at the consultant company Pöyry Sweden AB in Norrköping, whom performs the task for E.ON heating Sweden AB, Händelöverket in Norrköping. The report shows methods to manufacture slurry consisting of fly ash and water. The slurry shall be pumped into several former oil storage rock shelters that E.ON has put into operation for the specific purpose. The ash mixture also develops hydrogen gas in contact with water.The work has aimed to produce different suggestions of methods and equipment that can be used for the objective. Mixing method and security issues were in centre while working with the suggestions.

Sweden?s District councils and Country councils are in itself to a large extent responsible for the state financed welfare. Because of this, Sweden has a contribution- and adjustment system. The reason for this system is to create equal chance, for all District councils and Country councils, to be able to give the citizens service independently of their income and non-influential structural differences. The adjustment is built upon the so-called standard cost method, which contains four different parts.

This Thesis in Military Technology deals with experiences drawn from the forced introduction of Weapons Station 01, 2009. The work aims to identify the experiences regarding the forced procurement of military equipment to see how they can develop normal and fast procurement of equipment. The main conclusions of  this work, is to achieve greater capability and increase the military utility, are: -          Common objectives and priorities of stakeholders-          Response and joint types shall determine requirements for system-          Ensure an integrated project team also at lower levels-          Engage the integrated logistic support early in the materiel process-          Include Armed Forces staff as early as possible in the testing and validation-          Prioritize work to facilitate the rapid development of decision on use (BOA)-          Provide back up for increased redundancy in the mission area .

AbstractThe assignment were assigned by Camatec Industriteknik AB. Camatec is a Karlstadlocated consulting company, they make everything from pilot studies to complete projects in mechanical design and calculation. They even have their own patented product, Camcoil. It is a winder for steel strips and is used for example with hardening of the steel strip. The assignment has been to solve the problems encountered by some customers within this product.

This examination work is the final work in our education to become a Bachelor of Science inMechanical Engineering by the University of Lund.The main purpose with this work has been to develop a new effective material handling system for TPPM AB in Lund since the existing system starts to become out of date. The future system that is going to be installed shall have the capacity to support all machines with unit-, semi- and finished goods during full production. The work has also included studying the possibilities to change the material flow in a positive way between the storage and the production when one is using existing buildings.During our work we have been used a simulation program called AutoMod, performing company visits, interviews and reviewed internal and external information to create a picture of what the best conclusion can be. During the work we have contacted five suppliers to receive system solutions and quotatioris. The suppliers, which have been contacted, are Swisslog, Moving, Rocia, Christensen & Hansen and ABB.

This paper is the result of a case study conducted at Uppåkra Mekaniska AB during the spring of 2006. The task that was presented by Uppåkra was to develop a basis for a decision for the planning activities at the company, so that in the future they can create lot-sizes which are based upon a total cost perspective. Total cost in regards to lot-sizing is defined as the sum of the administrative reordering costs and warehousing cost per stock keeping unit.To collect data a series of interviews and observations were conducted. This data was then used during the lot-sizing simulation and analysis. The 15 units that the simulation was conducted on were grouped into three item classes depending how many different machine setups they required during the production process.