The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

How to use automatically read data to create a method that visually describes how energy is used in a building, the so called energy signature..

Solar energy is the one most talked about among energy sources due to its huge potential amongst renewable energy technologies. A greater use of the solar energy may be the solution to today's climate threats. Normally there are two different types of solar technologies, solar cells and solar thermal collectors. Solar cells convert solar energy in to electricity whilst solar thermal collectors convert solar energy into heat, which can be used to heat hot water for households. This goal of this study has been to investigate the possibility of implementing solar energy into the energy system of Kista Galleria, one of Sweden's foremost venues.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

The energy consumption in the sectors of residential and public buildings is 40 % of the total energy consumption in Sweden. The main part, 85 %, of the energy use in these sectors is for operation of the buildings. The rest is used in the building process. When energy-efficiency measures are taken the energy use during the operation time decreases and the fraction of energy consumption during the building time increases. This project is carried out in cooperation with JM AB and concerns the energy use during the building time of production of blocks of flats at the building site.The main part of the electricity that is used during the production of apartment buildings goes into the heating of portacabins and illumination of the building during the construction phase.

The Energy Performance Certification in Sweden was developed as a tool to achieve the Government's target to reduce Sweden's energy consumption by 20 percent by 2020. The Energy Performance Certificate has previously received some criticism for not fulfilling its purpose. Questions that formed the basis for this report is how the energy performance certification provides support to buyers of single-family houses and if the energy performance improved in terms of reliability. The report begins with a background description that describes how the energy declaration works and some of the findings of previous evaluations and surveys. A survey to investigate the broker's position to energy performance have been conducted as well as interviews with buyers and sellers of houses. An investigation whether the energy performance can vary between different calculation programs, depending on various assumptions made by the energy declarant, has been made.Brokers and sellers have proved negative attitudes towards energy performance, particularly brokers.

Calculated and measured energy in residential buildings is going to differ. The reason to this may be due to many factors. In this study there is a study on how these factors affect the energy use in a building. To get an insight in what defines energy, there is first a description of energy supply both worldwide and used in Sweden, followed by a description of the energy balance. In this study energy will be studied in residential buildings only.

Several scenarios point toward a future where we are far more people on Earth than today, where most of those people will live in cities and where oil no longer dominates in the transport systems and in agriculture as an energy source and where less energy will be available to us. The report investigates what areas in traditional ecological knowledge that can contribute to the transition that follows a future with less energy and establishes three areas with the potential of becoming important: areaspecific biological knowledge in societies that are more dependent upon its surrounding environment and its natural prerequisitesthe local management of these biological resources, which often means a fair sharing and sustainable handling of the resources and which has been observed in Nobel price awarded Elinor Ostrom?s researchthe world views that lie behind how the environment is considered and managed, world views that can inspire and point toward how we in the future should formulate world views that do not give the destructive modern management of the environment It is also noted that the magnitude of the city living in the future is a historical news and that very little research has been done in how traditional knowledge can be transferred into this kind of living..

Rising energy prices and higher energy demands have led to an increased focus on energy efficiency, in particular in the real estate business, where high potential for energy savings exists. Within the next few years, buildings that were constructed in the sixties and seventies will be in need of renovation. One of the challenges of these renovations will be to improve energy efficiency. A real estate company that is facing this challenge is Uppsalahem AB, based in the city of Uppsala, Sweden. This study focused on analyzing energy efficiency measures when renovating old buildings.

The Swedish building and property management sector are responsible for about 30 % of the total energy use. In order to take environmental consideration, different environmental assessment tools and standards are used. Miljo?byggnad, Svanen, FEBY12 and PHI are some of these. There has been increased interest to certify buildings and therefore it is of interest to evaluate the assessment of the energy field to see if relevant energy aspects are assessed.

The building and plant sectors represent a large part of Sweden?s energy use. Putting energy requirements in public procurement as a tool for reducing energy consumption in the building and plant sectors is therefor an opportunity that operators can take advantage of. The aim of this thesis was to map the energy requirements in procurement that operators in the public sector use today in building and plant projects. The analysis was made with respect to if the energy requirements corresponded to the parts with large energy use in building and plant projects and also in which way energy requirements in procurement are written in the contract.

The Island of Öland has one of the best wind climates for land based wind power in Sweden. An objective for the Island is to become self sufficient using electricity from renewable source of energy such as wind. There is currently 55 MW capacity installed on the Island and it is estimated that grid congestion will occasionally occur if more than 135 MW was installed.The aim of this thesis is to investigate he possibilities for load management by smart charging of electric vehicles, EV. The definition of smart charging is that the charging is done to some extent with an ICT-system, (information and communication technology) that correlates wind electricity generation to the charging of electric vehicles. The purpose is to avoid grid congestions on the sub-sea cable that connects Öland to the mainland because that in turn would curtail wind energy production.

ABSTRACTThe discussions about energy use have increased year by year everywhere in the society, and so also in the healthcare sector. But what is actually energy use in a hospital facility, and what affects it?The typical way today to express the energy use is in kWh/m2. The problem with a key performance indicator that is expressed as energy use in relation to a specific area is that it does not take into account the activity in the building. Even though the activity to a very high extent affects the energy use.

ABSTRACTThe discussions about energy use have increased year by year everywhere in the society, and so also in the healthcare sector. But what is actually energy use in a hospital facility, and what affects it?The typical way today to express the energy use is in kWh/m2. The problem with a key performance indicator that is expressed as energy use in relation to a specific area is that it does not take into account the activity in the building. Even though the activity to a very high extent affects the energy use.