The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

In today's society there is a significant focus on energy efficiency. Despite this, people leave lamps, televisions and computer screens etc. powered on unnecessarily. The goal of this project is to build a simple prototype for home automation where a user, via an application on a mobile phone, can switch on and off the power of an electrical products in the home and as well as being able to check whether such products are switched on or off. The prototype will also collect data on power consumption for these electrical products.

An energy study has been performed on two blocks in an area called Gävle Strand. The buildings are owned by a tenant-owner?s association called brf Carolina and were built by the company Skanska 2008. The builder as well as brf Carolina are pussled by the fact that electricity use is higher than expected while heating is less. Skanska is also very interested in finding out how much heat recovery from stale exhaust air through a geo-thermal heat pump is contributing to the general heating requirement and energy balance in four out of the ten buildings located on the properties.To find possible answers to the higher electricity use a literature survey on user behaviour was conducted.

A large amount of our time is spent indoors in an artificial climate. To make the experience pleasant there are requirements on the ventilation and the heating system. At the present time the most common form of heating is a radiator system complemented with a ventilation system. A ceiling heating system with combined heating and ventilation can replace the two separated systems. The benefit with a ceiling heating solution is that it saves space since the radiator system is no longer needed.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

How to use automatically read data to create a method that visually describes how energy is used in a building, the so called energy signature..

Solar energy is the one most talked about among energy sources due to its huge potential amongst renewable energy technologies. A greater use of the solar energy may be the solution to today's climate threats. Normally there are two different types of solar technologies, solar cells and solar thermal collectors. Solar cells convert solar energy in to electricity whilst solar thermal collectors convert solar energy into heat, which can be used to heat hot water for households. This goal of this study has been to investigate the possibility of implementing solar energy into the energy system of Kista Galleria, one of Sweden's foremost venues.

This Master degree project has been performed at the Braviken paper mill on papermachine 53 (PM53) which produces newsprint paper. The current economic situationhas contributed to declining demand for newsprint, which means it is extra important tobe competitive by high energy efficiency. Particularly as energy prices are expected torise when the economic growth returns.One way to increase energy efficiency is by reducing the water use in paper and pulpmills and consequently save energy through reduced heating of water. The thesis's maintask is to evaluate whether a water purification plant (microflotation plant) forpurification of process water in PM 53 is profitable. The microflotation plant enablesreuse of warm process water instead of losing the energy to receiving waters.

The present climate discussion has made energy efficiency an interesting topic. Saving energy does not only help the climate but also saves money for the energy consumer. The purpose of this thesis was to examine the potential of heat recovering from milk cooling. Two milk farms, one with voluntary milking system, VMS, and the other with conventional milking system was used to measure interesting temperatures and electricity consumptions. The numbers were used both to do theoretical calculations and to construct a SIMULINK model. To calculate the potential for heat at milk farms theoretical calculations were made in MATLAB using a reference farm with different combinations of heat recovery and pre cooling. The farm was assumed to keep a dwelling house with the annual heat consumption 18165 kWh.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

In June 2006 the Swedish government decided that the use of energy in buildings should be reduced by 20 percent until 2020, compared to the level of energy used in 1995. To contribute to this goal, the real estate company ?Eskilstuna Kommunfastigheter AB?, set up own goals for their buildings. In 2009, the goal for schools was to have a maximum energy use of 118 kWh/m2year for heating and hot water.The school ?Hållsta skola?, just south of Eskilstuna, exceeds the limit since it used 270 kWh in 2008.

Energy is an important issue in the current world which significantly affects sustainability and development. Energy generation and use are major sources of CO2 emissions which is one of the most important driving factors in global climate changes. The amount of energy used in house hold section can lead to estimation of the amount of CO2 emitted within this section which subsequently would be a ground to better management and maintaining a sustainable society. This study which is a bachelor?s project in sustainable energy, deals with estimation of CO2 emission from different types of residential houses in Sweden. An extensive literature review on energy use in Sweden by different residential sectors has been conducted.

The design of the building envelope affects the energy consumption of a building. As the energy requirements for new buildings are becoming more demanding, the performance of the building envelope must be improved. Energy efficiency and durability are important attributes to consider.This report includes investigations of the building envelope, moisture and passive solar energy. It is based on the analysis of two different buildings with different designs. These buildings stand as reference for two of the companies who are working on a new, climate smart, residential area in Uppsala, Sweden.Studies and analyses on energy consumption and moisture transportation were made.

Buildings worldwide account for 40 % of the total energy use. Climate change is of increasing importance, but few are willing to reduce their standard of living or get a higher cost for the change. Energy efficiency of existing buildings gives the greatest benefit economically and environmentally. The real estate company Klövern AB manages 46 properties in Karlstad. Heating is the major cost of the total operating costs of real estate. Rising energy prices increase the need for Klövern AB to improve energy efficiency and to investigate alternative sources of heat.

The sun is a huge energy source with great potential of providing energy to the heating of homes and other buildings in an environmentally sustainable manner. In order to provide buildings with energy from the sun it is necessary to transfer the energy supply over time to when the demand arises. By storing the heat in a seasonal storage, solar energy from the summer can be used in the winter when the demand for heating is greatest.Today's existing plants are mainly in Europe and particularly in Germany. These facilities are designed to supply heat demands greater than 400 MWh and covers about 40-50 % of this need which consists of energy for space heating and domestic hot water. How much of the heat demand that is covered, the solar fraction, is partly due to losses from the storage which in turn is connected to the surface area of the storage.