Sök:

Sökresultat:

190 Uppsatser om Electronics - Sida 1 av 13

En oscillatorbank till en lågfrekvensradar : LORA/VHF

The goal of this thesis work is to enable an existing UHF radar to operate in the VHF band instead. In order to achieve this, new coherent local oscillators are required. Different options are suggested and one of them is implemented and analyzed..

Design och konstruktion av laborationsutrustning till en kraftelektronikkurs

The purpose of this degree project was to build laboratory equipment for a new course in power Electronics that starts this autumn 2010 at Uppsala University. The equipment is intended for student labs and it covers the most important areas of the course including rectifying, buck-/boost-converters and PWM-modulation. It is built as one sealed unit where all the Electronics are built-in but visible and it has a connection board where students safely can connect the different circuits. The project has advanced from theoretical studies of circuit design, choosing of components and simulations to drawing the printed circuit board (PCB), soldering, case building, final testing and troubleshooting - basically most steps from an early idea to a final product. Measurements on the final product gave about the same results as the earlier simulations of the circuits and the result is overall satisfying..

Simulated Annealing : implementering mot integrerade analoga kretsar

Today Electronics becomes more and more complex and to keep low costs and power consumption, both digital and analog parts are implemented on the same chip. The degree of automization for the digital parts have increased fast and is high, but for the analog parts this has not come through. This have created a big gap between the degrees of automization for the two parts and makes the analog parts the bottleneck in Electronics develop. Research is ongoing at Electronics systems group at Linköping University target the increase of design automization for analog circuits. An optimizationbased approach for device sizing is developed and for this a good optimization method is needed which can find good solutions and meet the specification parameters.

Övervakningssystem för båtelektronik

Leisure boats of today have a lot of Electronics that needs battery power to work. In additionto that electric propulsion systems have gotten more popular lately, which further increasesthe demand for high battery capacity. The batteries used are mostly lead-acid batteries and toget the most out of the batteries it is important to treat them right. To optimize the electricsystem it is important to have knowledge of how the batteries and the electric motor are usedand which factors affect e.g. efficiency and recharging.A new electric drive that can replace old diesel engines is being developed and needs testingand evaluation.

Analys av information för förbättrad kapacitetsplanering: en
fallstudie vid Grundfos Electronics

Under hösten år 2005 implementerade Grundfos Electronics ett nytt ERP- system, vilket innebar en uppgradering från SAP/R2 till SAP/R3. I och med denna uppgradering fick Grundfos Electronics även tillgång till Grundfos Business Warehouse, vilket är en kombination av databaser som innehåller kvantitativ data från produktions- och försäljningsbolag i Grundfos- koncernen. Genom övergången till SAP/R3 och tillgången till Grundfos Business Warehouse öppnades det nya möjligheter till att ta fram information om Grundfos Electronics försörjningskedjor. Syftet med examensarbetet har varit att undersöka vilken information som finns tillgänglig i Grundfos Business Warehouse som kan användas för att skapa förståelse över hur Grundfos Electronics försörjningskedjor fungerar. En analys av informationen utfördes med syfte att förbättra kapacitetsplaneringen vid Grundfos Electronics.

Test och verifiering av en ny inkapslingsmetod för SiC BJT och MOSFET

The use of silicon carbide (SiC) as a base material in power Electronics has manyadvantages, including high breakdown voltage and excellent temperature endurance.However, the packaging of such Electronics presents major challenges and there is aneed for packaging that can operate in higher temperature. The purpose of this thesishas been to develop a test method and verify the functionality of SiC powertransistors prototypes with a new packaging technique developed by Swerea IVF AB.It includes setting up an electrical test-bed for power and high temperature cyclingand analysis of the results. Even though test confirmed functionality after thepackaging process, (at room temperature) the performance seemed to have been reduced. This could be a result of the measurement setup and the packaging process.In higher temperature the transistors failed to operate longer than a couple ofminutes which showed the weaknesses in the design and the challenges with this typeof packaging..

FPGA för displayhantering och grafikgenerering i fordonsmiljö

This report is part of the major thesis carried out at Stoneridge Electronics in Bromma,Stockholm during autumn and winter 2005-2006. The background to the thesis is the trendwithin the automotive industry where color displays have become more common for presentationof information to the driver, a trend that has come to the commercial vehicle market. Thepurpose of the thesis has been to evaluate whether programmable logic, with respect to FPGAtechnology, could be suitable for display control and graphics generation of these more complexcolor displays in automotive environment.Within the scope of the thesis the FPGA technology has been investigated, i.e. whatopportunities and threats there are with aspect to environmental and security requirements. Inaddition, the market of FPGAs and pre-built IP-cores has been investigated.

Reducera omställningstiden i ytmonteringslinan Panasonic på Stoneridge Electronics AB

Omställningstiden i ytmonteringslinan Panasonic på Stoneridge Electronics AB ansågs vara en bidragande orsak till att maskinernas fulla kapacitet inte kunde utnyttjas. Syftet med det här examensarbetet var därför att analysera omställningssituationen och med analysen som grund reducera omställningstiden med hjälp av SMED-metoden samt ta fram förbättringsförslag gällande arbetet i övrigt.Förutom SMED har tidsmätningar, observationer samt litteraturstudier legat till grund för reduceringen av omställningstid samt förbättringsförslagen som innebär bl.a. sekventiell omställning av conveyersystemet i ytmonteringslinan samt tydligare instruktioner och mer visuell styrning, enligt teorin om Lean.Ett fortsatt arbete i form av uppdatering av arbetsinstruktioner och själva utförandet av omställningen är exempel på typen av ständiga förbättringar som företaget redan idag jobbar aktivt med..

Mjukvaruverktyg för loggning och analys avindustriella processer

This report discusses developing a software log tool for analysis of industrial processes. The target was to develop software that can help electro Engineers for monitor and fault finding in industrial processes. The tool is called PLS (Process log server), and is developed in Visual Studio.NET Framework 2005. PLS works as a client with Beijer Electronics OPC Server. The program is able to read data from PLC (Programmable Logic Controller), trough the OPC Server.

Högeffektslysdioder. Möjligheter och förutsättningar för högeffektslysdioder som belysningskälla - ett demonstrationsbygge

This report examines the prerequisites for LEDs to replace other technologies indifferent applications. How does the different technologies for light generationwork and what are the advantages and disadvantages? The various technologieslimitations and characteristics provides the opportunities for the LEDs.This report describes a test-construction built to examine what practical arrangementscan be built with modern light emitting diodes, in order to showsome of the possibilities. The construction consists of three different applications,a high power lamp based on cold white LEDs, one based on warm whiteLEDs for the evaluation of the light characteristics and a RGB-LED based lampable to mix any colors quickly and seamlessly. The test construction also containsthe essential peripherals including control-Electronics, optics and a custombuilt watercooling solution.The potential for LEDs is huge but it is complicated to build LED based applicationsdue to the limitations which mainly includes the Electronics and theneccesary cooling.

Uppförsäljning - en väg till ökade snittköp

The Swedish consumer electronic industry has recently experienced an increasingly intensive price war. The price war has forced some operators in the business to declare bankruptcy, as the only way to compete has been by driving down prices. A challenge that retail chains in the consumer Electronics industry is facing is to increase their margins. If store personnel can success with upselling, the companies will increase their profits. The purpose of this paper is to examine if the sales people in the consumer electronic industry can influence the customer to buy a more expensive product and what the effects the upselling has on the customers' attitudes.

Design och tillverkning av en stereoanläggning med aktivt delningsfilter

This thesis is the result of the author?s interest in music and Electronics, namely the design and manufacturing of a stereo sound system with an active crossover. In short it can be stated that an active crossover has many advantages over its traditional passive counterpart. The active design naturally results in a more complex system comprised of a multiple number of components. This report deals with the theoretical aspects of preamplifiers, crossovers and power amplifiers as well as power supply and control.

Automatiserad konstruktion av analoga förstärkare

The last few decades the development in the field of Electronics has been huge. The components performance gets better at the same time as the manufacturing cost decreases. Many of the design moments that have to be done, are done automatically today, but it can get better. Especially for analog circuit design.At Electronic System in Linköpings universitet, research is in progress to develop a tool that can design analog circuits in reasonable time. It means that it has to size the components (transistors, resistances, capacitances etc), so that the circuit can fulfill the performance requirements.

Skalning och brusberäkning av tvåportsadaptorer

The goal of this work is to summarize the calculations for scaling and noise of twoportadaptor. Two different methods has been described and used for the final results..

Konvertering från luft till vätskekylning av elektronik

A Swedish Electronics company wants to make the cooling of one of their electronic components more efficient. They propose that a retrofit liquid cooler is the way to achieve this goal. The current air cooling has high energy cost due to the high amount of power needed to power fans and heat exchangers. Using high volumes of air for cooling also leads to noise pollution. The conversion from air to liquid cooling would possibly make the operation of the Electronics more cost efficient and less noisy.The purpose of this project is to theoretically evaluate different concepts of drawing the heat generated by the electronic component in to a fluid, using numerical calculations in Matlab and FEM simulations in ANSYS.

1 Nästa sida ->