This report is a bachelor thesis presented at the department of Computer Science andEngineering at Chalmers University of Technology. The aim for the project is to find a simplemethod to measure and display physical quantities in a three dimensional room.The report describes a method to construct a system for measuring differentphysical quantities via sensors. The system must be built in a modular and expandable way tobe adaptable to different tasks.The system explained in the report consists of two parts;A physical scanner with moveable probes for carrying sensors and a microcontroller forcontrolling the probes and communicating with the next part.An application written in Java for storing the measured values and presenting them in a lucidperspective.It is possible to construct the scanner with different designs and circuitry, with multiplexers andflip-flops, to ensure that an unspecified number of probes can be added to the system and thatthey can be operated simultaneously.The Java application is written in a modular way, using a design pattern that separates eachindividual part of the application. It contains exceptions and interfaces that ensure a safe andexpandable application..

Electronic article surveillance (EAS) is widely used in shops and libraries together with an RF-tag attached to the goods or books in order to prevent shoplifting. By implementing the addition of a moisture sensor to the RF-tag, other functions become possible, including the ability to use as an alarm with regards to frozen goods, which have been shipped but which have melted and have, subsequently, refrozen. In- relation to care for the elderly, one time-consuming step involves checking whether there is the necessity for a change of diaper and this can, instead, be based on an RF-tag with an EAS-system alarm. A preliminary investigation was made using the moisture sensors, which involved how the resistance changes when liquid and/or heat is applied. A simulation of the LCCR circuit (RF-tag with the sensor) was conducted in order to determine how the resonance frequency changes for different resistances levels.

The aim of the Master?s Thesis work is to study and develop algorithms for autonomous travel of a UGV (Unmanned Ground Vehicle). A vehicle for the mounting of sensors has been constructed in order to perform the work. Since the UGV is to be used outdoor in urban areas, GPS can be used. To improve precision and robustness, inertial navigation is used in addition to GPS, since GPS reception is likely to be diminished in such areas.

Rapid Granulator is one of the world's largest producers of granulators, which is a kind of grinderwho grinds discarded plastics to granules which later can be reused when pressure molding plastics.The company wanted help in developing a new, or alternatively extending their previous,measurement equipment. The old equipment was hard to use, required changes in the code fordifferent measurement scenarios and had a limited array of measuring quantities. Rapid had an ideaof a similar concept only with a greater number of input ports, better range of applicable sensors andan advanced yet easy to use interface. The system is supposed to be placed at Rapid's test departmentwhere it will be used as a tool for finding faults and provide data which can be used for furtherdevelopment of the granulators.The project's members accepted the task and immediately began searching for suitable componentsfor the system. After the search was completed a list of costs, limitations, sensors, I/O's anddevelopment environment was presented to Rapid's staff.

Sweden's drinking water quality is considered to be high partly due to a high quality of the raw water and a well developed sewage infrastructure. Despite this, there is water contamination that could be prevented by installation of a sophisticated early warning system. Some of the major players in the production of drinking water have already invested in different types of early warning systems to ensure drinking water of high quality. There are various forms of early warning systems where automatic monitoring of E. Coli is an interesting alternative.

This report is a bachelor thesis presented at the department of Computer Science andEngineering at Chalmers University of Technology. The aim for the project is to find a simplemethod to measure and display physical quantities in a three dimensional room.The report describes a method to construct a system for measuring differentphysical quantities via sensors. The system must be built in a modular and expandable way tobe adaptable to different tasks.The system explained in the report consists of two parts;A physical scanner with moveable probes for carrying sensors and a microcontroller forcontrolling the probes and communicating with the next part.An application written in Java for storing the measured values and presenting them in a lucidperspective.It is possible to construct the scanner with different designs and circuitry, with multiplexers andflip-flops, to ensure that an unspecified number of probes can be added to the system and thatthey can be operated simultaneously.The Java application is written in a modular way, using a design pattern that separates eachindividual part of the application. It contains exceptions and interfaces that ensure a safe andexpandable application..

Varje år i Sverige sker ca 24 000 skallskador på grund av yttre trauma och 30 000 strokeskador. Ett betydande antal får sekundära skador på grund av den ökade vattenhalten kring den skadade hjärnvävnaden. Föreslagen metod är att inducera vattenflöde från skadad till frisk vävnad baserat på teorin om elektroosmotiskt flöde. Teorin bakom elektroosmotiskt flöde är att ett flöde induceras då en spänning läggs över ett medium. Elektroosmotiskt flöde tillämpas i industrin och kallas då electro-osmotic dewatering (EOD).

During test flights SAAB uses the data acquisition system COMET 16. The part of the system that receives the signals from the sensors and converts them is called KSM 15. The purpose of this thesis is to develop a data acquisition module on stacked PC/104 modules with a lower production cost. Our work has been divided into one part about analog signal conditioning and a second part with digital filtering and memory management of the sampled data. The analog part, designed of regular components like instrument amplifiers, voltage references, operational amplifiers and multiplexers, adjusts the sensors signal levels for the ADC?s that converts the signals.

This report is the result of a diploma work made at IMT at US in Linköping. The purpose of this piece of work is to investigate the possibility to design a general program for data-acquisition using LabVIEW, suiting different hardwares and connections. Great importance has been attached to communication with serialport, using bluetooth, because different wireless PPG-instruments has been developed parallel to this project. These PPG-circuits uses this type of serialcommunication. Communication with USB, GPIB and analog connection has also been examined and analog communication has been tested practically.

Sweden's drinking water quality is considered to be high partly due to a high quality of the raw water and a well developed sewage infrastructure. Despite this, there is water contamination that could be prevented by installation of a sophisticated early warning system. Some of the major players in the production of drinking water have already invested in different types of early warning systems to ensure drinking water of high quality. There are various forms of early warning systems where automatic monitoring of E. Coli is an interesting alternative.

In industries today the demand for reading the state of industrial equipment and thus prevent machine breakdown, is increasing. The company HMS Industrial Networks AB has a product on the market, Netbiter EC350 that is used to read sensors and thus find out the condition of industrial equipment. By reporting scanned data to users through a cloud service, users can keep track of their equipment. When developing Netbiter EC350 a slot was made for a Bluetooth module to offer clients a wireless reading in future developments. In this project a prototype was made to show how this Bluetooth communication can be implemented. The goal of the project was to create a Bluetooth communication between a Bluetooth sensor and Netbiter EC350. A user interface was made to allow the user to read sensor values. The result of the project shows how a Bluetooth communication can be implemented to read sensors wireless and therefore it fulfills its purpose and goal.

The aim of the study was to find repetitive behavioral patterns pre calving that could be used as indications of calving in beef cattle. In the study sixteen Standing- and lying down sensors were attached to the leg of sixteen beef cows. Ten of the sixteen beef cows gave birth to calves during the trial period. From these ten cows, data from six cows were used to assess the sensors fitness for use as calving indicators. The analytical part of the experiment was divided into two parts, calculation of divergence of mean lying time within different time intervals, and the number of lying bouts.The first part consisted of optimization of an equation used to highlight divergence in mean lying time within eight different time intervals (3, 6, 9, 12, 15, 18, 21 and 24 hours).

The purpose of this thesis has been todesign an electric circuit that measurestemperature in three different ways. Asoftware was also designed to record andanalyse the measurments. The result of thecircuit was a PCB with inputs for 42sensors of both surface and non-surfacemeasurments. These all have a maximumerror of ±3°C..

Mitt arbete handlar om mötet mellan rysk konstruktivism och science fiction. Detta har jag gestaltat i ett textilt rum inspirerad av science fictionkarraktären Doktorn ur Doctor Who. Doktorn är en utomjording av en långt mer utvecklad art och från en mer avancerad civilisation än människorna, som reser i tid och rum i sitt tids-och rymdskepp TARDIS. Jag har designat ett rum som är min textila tolkning av TARDIS innersta. Arbetet kretsar kring tankar om gestaltning av en flerdimensionalitet som bara kan anas, inte ses eller förstås.

The problem of separating a non-rectangular foreground image from a background image is a classical problem in image processing and analysis, known as matting or keying. A common example is a film frame where an actor is extracted from the background to later be placed on a different background. Compositing of these objects against a new background is one of the most common operations in the creation of visual effects. When the original background is of non-constant color the matting becomes an under determined problem, for which a unique solution cannot be found. This thesis describes a framework for computing mattes from images with backgrounds of non-constant color, using Bayesian statistics.