Purpose: The aim of the thesis is to identify principles of valuation and to reach a solution for how Statens järnvägar can present their leased railroad vehicles in the future.Methodology: The authors have done a case study through a qualitative approach. Interviews have been done with Statens järnvägar, Näringsdepartementet and Riksrevisionen. Annual reports from Banverket and Luftfartsverket have been studied.Theoretical perspectives: The regulations that rule the authorities are a base for the study.Earlier researches done within the subject are presented in this section.Empirical foundation: The empirical foundation of this study consists of primary- and secondary data. The primary data is collected from the interviews that have been done, whilst the secondary data is composed of annual reports, regulations and various other documents.Conclusions: The authors have come to the conclusion that the method of valuation that Statens järnvägar choose, depends a lot on the vehicles hypothetical future. It is difficult to say that only one of the methods would be the correct one..

I denna rapport utvärderas Scanias basbilar som används av svensk räddningstjänst. Rapporten grundar sig på platsbesök hos de involverade aktörerna samt en enkätundersökning genomförd på räddningstjänsten i Luleå. I rapporten framkommer att räddningstjänstpersonalen i Luleå sammantaget är ganska nöjd avseende basbilarna. Många synpunkter och kommentarer har lämnats, men mer i ett förbättrande än kritiserande syfte. Vissa kritiska punkter har dock identifierats och det som fått allra mest kritik är jalusierna till verktygsfacken som anses bristfälliga på flera punkter.

This thesis has been adjusted because some parts are classified, some sentences might have been changed. Electric bikes are a convenient mode of transport, a good choice when long distances or tough slopes can be an obstacle.The goal of the project was to create a prototype on a locking mechanism with an inductive charger for electric bikes.The idea behind the project was to develop a user-friendly locking mechanism, where the bikes would be charged inductively when they were locked. To implement the project facts about induction, battery charging and locking devices was needed to be acquired. Circuits for induction charging were created and a lock device was constructed. A microprocessor was used to control the entire system.A prototype was designed with a locking device and an inductive charger fixed in a bike rack.The entire project became very wide which resulted in that not all of the parts of the project could be completed.

 With the increases in fuel costs due to the depletion of the world oil reserves and the increase of greenhouse gasses as a consequence to using oil as a fuel many companies are looking to new and innovative ways to power their aircraft. One of these new ways to power an aircraft is using fuel cells powered using hydrogen and oxygen, thus producing nothing but water vapour and small amounts of nitrogen dioxide as well as trace amounts of other emissions. Both Boeing (1) and Politecnico di Torino (2) have shown that it is possible to build an all-electric aircraft powered by fuel cells. Both flights used small, two-seater aircraft and a constant between them was the loss of the co-pilot seat due to weight and lack of space. As this paper will deal with a commercial aircraft a primary concern is the cargo and passenger capacity and whatever impact switching propulsion system has on these.

This thesis has been adjusted because some parts are classified, some sentences might have been changed. Electric bikes are a convenient mode of transport, a good choice when long distances or tough slopes can be an obstacle.The goal of the project was to create a prototype on a locking mechanism with an inductive charger for electric bikes.The idea behind the project was to develop a user-friendly locking mechanism, where the bikes would be charged inductively when they were locked. To implement the project facts about induction, battery charging and locking devices was needed to be acquired. Circuits for induction charging were created and a lock device was constructed. A microprocessor was used to control the entire system.A prototype was designed with a locking device and an inductive charger fixed in a bike rack.The entire project became very wide which resulted in that not all of the parts of the project could be completed.

The fork lifter chipper truck is a concept which has been developed for harvest and transport of bio fuel. The system consists of one fork lifter chipper truck and 1, 2 or 3 transport lorries, usually two, which serves the fork lifter chipper truck. The system is driven by the fork lifter chipper truck that produces chipped material into a container on the truck. When the container has been filled the truck drives to the landing site where it?s offloaded.

Self-driving cars are soon to become a reality to the commercial market. A self-driving car does not have a human operator, which enables some interesting characteristics. The main benefits are considered to be:The number of accidents and traffic jams should be reduced.Enhanced comfort.Energy usage could be decreased while capacity could be increased.This study concerns the causes for improved energy efficiency. The reason for improved energy efficiency is mainly because of the variation in terms of acceleration, braking and distance holding are reduced. The vehicles are more intelligent and can work together as a unity.

When designing roads it?s important to knowwhat loads will bedriven on it. The axles on heavy vehicles can either have super single tires ordual tires which, according to studies, damage the roads differently. The SwedishTransport Administration is developing an understanding for the character ofthese different kinds of axle and tire types on the loads induced on Swedishroads. In this thesis a field study was conducted to determine the distributionbetween axles with super single tires and axles with dual tires on heavy vehicles.A highway, a country road and a national road were investigated during thestudy.

In Uppsala CHP Plant, there are six pressure reducing valves to reduce the pressure from 15 to 3 bars, before six absorption heat pumps. During the process the energy is conserved but losses occur in form of exergy. The aim of this thesis is to reduce the losses of exergy. This can be done by letting turbines replace the pressure reducing valves.In this thesis an investigation has been done of the conditions today, the conditions after the change from pressure reducing valves to turbines and a comparison of three different types of turbine solutions. The three examined solutions are one turbine, several helical screw expanders and several small turbines in parallel with asynchronous generators.The six absorption heat pumps have been divided into two groups; one group of four and one group of two absorption heat pumps.

This report is the result of a thesis as been implemented during the spring term 2009 atthe University of Gävle.The company Bruks produces mobile chippers which are used for chipping loggingslash, roundwood and parts of trees. The chipper is powered by a separate diesel engineand the chipper can be assembled on trucks, trailers or some other carrier vehicles.When the chip has passed the chipper drum, the chip is collected in an integrated binwhich is mounted on the vehicles frame with dumping yokes. When these dumpingyokes were designed they were probably created with large material dimensions. Theaim with the degree project is hence to study the strengths of materials and, if possible,to suggest an arrangement that can decrease the total weight on the dumping yoke onBruks´ mobile chippers 805 CT.The CAD-program Pro/ENGINEER was used during the project for outlining the 2Ddrawings,as distributed of constructors on Bruks, to solid 3D-parts. The three-dimensionalassembly from Pro/ENGINEER was transferred to Pro/MECHANICA.

Self-driving cars are soon to become a reality to the commercial market. A self-driving car does not have a human operator, which enables some interesting characteristics. The main benefits are considered to be:The number of accidents and traffic jams should be reduced.Enhanced comfort.Energy usage could be decreased while capacity could be increased.This study concerns the causes for improved energy efficiency. The reason for improved energy efficiency is mainly because of the variation in terms of acceleration, braking and distance holding are reduced. The vehicles are more intelligent and can work together as a unity.

Unmanned aerial vehicles (UAV?s) are nowadays greatly appreciated. The advantage over manned airplanes are great since UAV?s can be much smaller and therefore lighter. The goal of this project is to evaluate the performance of an environmentally friendly UAV using only lithium-ion batteries.

Användningen av personbilar har ökat stadigt i Sverige och världen i stort de senasteåren, vilket lett till ökade utsläpp av koldioxid. Samtidigt har oljepriset nåttrekordnivåer, och många menar att utvinningen av olja redan har nått sin topp. EU hardessutom satt som mål att medeltemperaturen på jorden inte får stiga med mer än maxtvå grader Celsius, och att till år 2050 reducera koldioxidutsläppen med 80 %. Detta ärenbart möjligt om nya, gröna drivmedel och drivlinor fortsätter utvecklas ochframförallt kommersialiseras. Användningen av förnyelsebara energikällor har ökatkraftigt, vilket skapat förutsättningar för bilar drivna av el.

The task was to design and manufacture a submersible displacement pump working with the wobble plate principle. The main task for the Wobble plate pump is to be used as a sewage pump for smaller households or dewatering pump in environments where small flows and high pressures are acquired. For these purposes ITT Flygt sell a screw pump, PC-Grinder 3068. The hydraulic part of the PC-Grinder is manufactured by a subcontractor. Therefore ITT Flygt wants to evaluate an alternative to their screwpump PC-Grinder, which can be entirely manufactured by them self.

Renewable energy and the charging of electrical vehicles will increase in the future. Therefore the risk of outages is also increasing, partly because renewable energy is intermittent and the production amount can change fast. Charging electrical vehicles is often demanding high effect in short time, which could make faults occur. It takes more advanced technology to short the outage time. Today Övik Energi has high reliability in the power grid, but in order to maintain the reliability, it is time to prevent problems that can occur in the future. This thesis has presented a suggestion for the placement of fault detectors Protrol IPS2, in which a total of four detectors is proposed.