Vilka effekter ger särskilda insatser till personer som är uppsagda till följd av varsel? Denna uppsats syftar till att undersöka effekterna på återgång till arbete av extra-insatta utbildningar som syftade till omställning vilka fanns tillgängliga för de som varslades vid Volvo Cars och dess underleverantörer 2008/2009. Effektutvärderingen utgår ifrån överlevnadsanalys där projektgruppen matchas mot en kontrollgrupp bestående av samtliga övriga varslade i Sverige. Resultaten visar att gruppen som tog del av utbildningsinsatserna hade signifikant långsammare återgång till arbete jämfört med en matchad kontrollgrupp..

Design of a house requires knowledge of both technology and economics. Heating and ventilation shall be designed, costs are calculated and estimated and requirements must be fulfilled. Which heating system is to be elected is also a difficult choice, especially with rising energy prices as a factor.The choice of energy system is not always given, because it depends on several factors. Below is a comparison between district heating, geothermal heat pump and electric boiler from an economic standpoint. In a previous report appears district heating and geothermal heat pump as the best options.

 This abstract describes the bachelor degree thesis in computer technology at Växjö University. The company BSR in Växjö has requested an application that can measure a cars performance, with attributes like acceleration times and engine power estimation. The communication between car and computer is via the USB port on the computer and the OBD-II socket on the car with the network protocol CAN, controller area network. Cars from VAG have been the primary focus group and the application has been tested on a Volkswagen Passat CC from 2009. The system is developed in the programming language C# in the environment Visual Studio with the framework .NET.

The aim of the present study was to estimate the correlation between Euro NCAP pedestrian rating scores and injury outcome in real-life car to pedestrian crashes, with special focus on long-term disability. The study also surveyed most frequently injured body regions and risk differences for specific elements of pedestrians hit by cars. Another aim was to determine whether Brake Assist systems affect the injury outcome in real-life car to pedestrian crashes and to estimate the effect in injury reduction of a high Euro NCAP ranking score combined with Brake Assist.In the current study, the Euro NCAP pedestrian scoring was compared with the real-life outcome in pedestrian crashes that occurred in Sweden 2003-2010. The real-life crash data was obtained from the data acquisition system STRADA, which combines police records and hospital admission data. The medical data consisted of International Statistical Classification of Diseases and Related Health Problems (ICD) diagnoses and Abbreviated Injury Scale (AIS) scoring.

Title: To build and transport brands to the Internet ? A qualitative case study of Getinge Infection Control and von Braun Sports Cars. Seminar date: 2009-06-09. Course/ subject: FÖ6016, Degree Project Undergraduate level, 15 University Credits Points (ECTS). Authors: Kristoffer Eriksson and Erik Kaplar.

This thesis is a feasibility study for a future product development project. The purpose ofthis project is to evaluate the possibilities and difficulties associated with the design of anelectric power assist servo for all terrain vehicles (ATVs). The project has been carriedout in collaboration with Nira Control AB. Nira designs and manufactures electric andelectro mechanic products mainly for the motor sport market segment.Nira Control AB is developing a fuel injection system for a new line of large ATVs oncommission. To be able to compete with manufacturers like Yamaha and Honda thecommissioner should be able to offer optional power assist steering.

Sekretessbelagd.

Volvo Cars in Skövde manufacture and assemble Volvo engines. When attaching the ignition coil to all 4-cylinder engines, a special mounting tool is required. This mounting tool is currently manufactured from injection-molded polyoxymethylene (POM), a thermoplastic. It has been noted that the life span of the tool is shortened as a result of abrasive wear that occurs during the attachment process of the ignition coil.An investigation of the possibility of manufacturing the mounting tool with a 3D-printer is undertaken in cooperation with ÅF, a consultant to Volvo Cars. A literature study is first presented to introduce broader knowledge on the subject.

The Smart Grid technology has during the last decade been established as a way to create a greater flexibility on the electricity grid that will be needed as the development moves towards an increased share of renewable primary energy sources in the electricity production. One part of the Smart Grid technology is the ability to shift loads in time, to adapt to either price or emissions, known as Demand Response. This project, which was conducted at KTH in collaboration with the consulting corporation Capgemini, examines the economic, environmental and social aspects of the Demand Response technology. In the project, three household products are used in a model that derives the potential savings in costs and emissions of CO2e. The results show that the actual savings measured in SEK are small, but that the savings measured in percent can be as high as 20 percent. Reduction of CO2e emissions is slightly lower.

Tumble dryers and drying cabinets have to a large extent replaced the traditional way of drying clothes outdoors. They are faster, more convenient, require less space and can be operated regardless of weather conditions. This replacement has significantly increased residential energy consumption, due to the fact that tumbles dryers consume large amounts of electrical energy. In the USA 9 % of the households electric energy is consumed when drying clothes. Over 4 million tumble dryers are sold in Europe each year and 20 % of the residential electricity consumption in Sweden is used drying and washing clothes.

The Smart Grid technology has during the last decade been established as a way to create a greater flexibility on the electricity grid that will be needed as the development moves towards an increased share of renewable primary energy sources in the electricity production. One part of the Smart Grid technology is the ability to shift loads in time, to adapt to either price or emissions, known as Demand Response. This project, which was conducted at KTH in collaboration with the consulting corporation Capgemini, examines the economic, environmental and social aspects of the Demand Response technology. In the project, three household products are used in a model that derives the potential savings in costs and emissions of CO2e. The results show that the actual savings measured in SEK are small, but that the savings measured in percent can be as high as 20 percent. Reduction of CO2e emissions is slightly lower.

The project Easy Battery Handling - EBH has been carried out in our auspicial and completedfor Devantini Corporation, a development company in Halmstad with its main concern inenvironmental friendly innovations.EBH has solved one of many technical challenges in one of Devantini corporation?s largerprojects. This main project involves the development of an electric powered formula racingcar. The part of this car that involved EBH was the battery handling to guarantee safe andquick battery exchanges during pit-stops.The solution became an entire battery module, hanging on the side of the car on two spearspointing out from the car. The batteries are exchanged by a specially designed trolley that isinserted under the battery module.

The Smart Grid technology has during the last decade been established as a way to create a greater flexibility on the electricity grid that will be needed as the development moves towards an increased share of renewable primary energy sources in the electricity production. One part of the Smart Grid technology is the ability to shift loads in time, to adapt to either price or emissions, known as Demand Response. This project, which was conducted at KTH in collaboration with the consulting corporation Capgemini, examines the economic, environmental and social aspects of the Demand Response technology. In the project, three household products are used in a model that derives the potential savings in costs and emissions of CO2e. The results show that the actual savings measured in SEK are small, but that the savings measured in percent can be as high as 20 percent. Reduction of CO2e emissions is slightly lower.

The Smart Grid technology has during the last decade been established as a way to create a greater flexibility on the electricity grid that will be needed as the development moves towards an increased share of renewable primary energy sources in the electricity production. One part of the Smart Grid technology is the ability to shift loads in time, to adapt to either price or emissions, known as Demand Response. This project, which was conducted at KTH in collaboration with the consulting corporation Capgemini, examines the economic, environmental and social aspects of the Demand Response technology. In the project, three household products are used in a model that derives the potential savings in costs and emissions of CO2e. The results show that the actual savings measured in SEK are small, but that the savings measured in percent can be as high as 20 percent. Reduction of CO2e emissions is slightly lower.

This thesis has been adjusted because some parts are classified, some sentences might have been changed. Electric bikes are a convenient mode of transport, a good choice when long distances or tough slopes can be an obstacle.The goal of the project was to create a prototype on a locking mechanism with an inductive charger for electric bikes.The idea behind the project was to develop a user-friendly locking mechanism, where the bikes would be charged inductively when they were locked. To implement the project facts about induction, battery charging and locking devices was needed to be acquired. Circuits for induction charging were created and a lock device was constructed. A microprocessor was used to control the entire system.A prototype was designed with a locking device and an inductive charger fixed in a bike rack.The entire project became very wide which resulted in that not all of the parts of the project could be completed.