This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

The energy in laundry rooms, in form heated air, can be utilized with a heat exchanger. A concept and an early prototype of the heat exchanger have already been developed to show that the theory works. This report describes the continued development and construction of the product.A field study was made in order to investigate the environmental usage and establish the product design. The most common washing machine was used as a calculation model, and calculations were also made to estimate the amount of energy in the air. A previous analysis of the existing prototype is also presented in this report, to show the products potential capacity.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

Målet med examensarbetet var att skapa ett verktyg för insamling av erfarenhetsdata för produktutvecklingsprocessen. Den skall vara användbar för att bidra till ett systematiskt arbetssätt för produktionsanpassad konstruktion på Volvo Aero Corporation. Det skapade verktyget för insamlande av erfarenhetsdata skall bidra till att produktivitet och producerbarhet kan förbättras på kommande koncept och konstruktioner. En förstudie har genomförts på företaget under hösten 2010 vilket ligger till grund för det beskrivna problemet i examensarbetet.Arbetet avgränsades till att utveckla en struktur för hur metod och erfarenhet skall struktureras och en testversion av verktyget togs fram för utvärdering. Efter samråd med den handledande Verksamhetsutvecklingsgruppen, VU-gruppen, från avdelning 9931 Projekt-, Koncept- och Tillverkningsledning, beslutades att examensarbetet skulle avgränsas ytterligare till insamling av diametermått på komponenten Diffuser Case på Volvo Aero.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

In this paper we have studied possible future uses for Additive Manufacturing (commonly referred to as 3D-printing) in Space. More specifically we have sought to establish how Additive Manufacturing can be used to construct structures on the Moon. Our studies have shown that Additive Manufacturing has great potential for establishing colonies on not only the Moon, but perhaps even further away from our home planet. With Contour Crafting-technology in combination with ISRU (In Situ Resource Utilization) we could, with material already present in the sediment layers of the Moon, construct advanced structures without having to transfer any extra material from Earth. This would lower the costs of establishing a colony on the Moon to such extents that it could actually be fiscally possible..

 The purpose with this thesis was to develop a designguideline which will simplify the development of new products that will be laser welded. The need for this thesis has come forward from the quality problems that Volvo Construction Equipment, Components Division is having with their laser welding manufacturing unit. The reason for the problems emerges from the bad communication between the development unit and the manufacturing unit within the company when the products produced today was developed. This resulted in products that were hard to and in some cases almost impossible to weld. To avoid these problems from occurring again it was needed to gather the experiences within this area and compile it and present in a brief a pedagogical manner. The information for the groundwork of our results has been gathered by interviews of several key persons in Volvo Construction Equipment, Components Division.

This thesis is the result of the class Examensarbete, 15 credits of the mechanical engineering program at Halmstad University. The class represents the final part of the program with the aim to attain a Bachelor of Science. It´s a project made during the spring 2014 in collaboration with Alutrade AB and ScanBox Thermo Products AB.The assignment is to develop a new transportation trolley for ScanBox. The aim is to complement their range with a product that opens up to new markets. That set new demands for materials and also manufacturing- and assembly methods.

At a manufacturing company, due to the competition the price is reducedtowards the manufacturing cost. Therefore it is important to maintain control ofones costs and keep calculations up-to-date.This thesis deals with cost accounting at a aluminium-processing company. The report focuses on calculating machine cost per hour since the manufacturing costs are the major part of the total product cost.Managers on the company believe that the costs they use in calculations todayneither is up-to-date nor advantageous in a market aspect and due to that their calculations need to be revised. The machines cost per hour is a major part in the manufacturing calculation. The company wants to provide a competitive price that also covers their costs.

The thesis investigates if it is possible to replace several pumpimpellers with one controllable pumpimpeller, with a economical and a manufacturing analisys aspect. The studied pumpimpeller is mounted on a midrange wastewaterpump, N3127MT.In the thesis a contemplated manufacturing process is evaluated for a concept that are supposed to act as a controllable pumpimpeller. The pumpimpeller are studied in a manufacturing and flow matter and are presented in the thesis.The manufacturing cost is also estimated, and this has been compared to the storage cost and other costs that the existing pumpimpeller generates.The thesis also shows that the concept has minor losses in cutting quality aswell as the effiency comparing to the existing pumpimpeller.The concept also raises the manufacturing cost and this increasing cost makes the presented concept to expensive to carry through.An investigation of the costs that the existing pumpimpeller produces has also been done, and this shows that there is not that much expenses to earn regarding to for example the storage cost. The storage cost includes information from Flygt?s central storagecenter in Lindas, Sweden and Metz, France, and also an inventory about the pumpimpellers located at Flygt?s different distributors worldwide.The thesis shows that a controllable pumpimpeller will generally increase the cost for the pumpimpeller and the performance of the pumpimpeller will decrease..