Denna rapport redogör för skapandet av varumärket Deco Retro. Samt den tillhörandedesignprocessen för att skapa en visuell identitet och profil för varumärket. VarumärketDeco Retro togs fram som ett undervarumärke till Kitsch Sweden AB som behövde ettvarumärke som passade deras nuvarande och framtida produkter. Deco Retro ska bidra meden stärkt identitet och värde för de produkter som ska säljas under varumärket. Designarbetetkring varumärket strävade framförallt efter att kommunicera den idé, identitet och de värdensom under projektet tagits fram för varumärket, samtidigt som det ska ha bidragit med enestetiskt tilltalande grafisk design.

In this thesis a rural network in Norrbotten, Sweden, has been to designed and planned with the purpose of improving distribution reliability by exchanging existing overhead lines with underground cables. General network design considerations are discussed as well as the ones for the specific low voltage grid. During the design phase the maximum power of domestic consumers has been estimated using Velander?s method. Currents, voltage drop and impedance of the network have been calculated and fuse operation and selectivity has been considered.

About 80 % of all Swedish dairy cows are kept in tie-stalls, but loose housing is increasing, probably because it is more profitable for the farmer. The design of the floors is of cruicial importance to the cows well-being. Traditionally, the most common type of floor in the alleys of a cubicle system still is a slatted manure-draining floor made of concrete. The typical Swedish design has 125-mm slats and 40-mm slots, maximally. With too wide slots, there is an increased risk of injuries to the claws when the cow makes a hasty move.

Title: An encounter with an unknown piece of music. This essay describes the mechanisms involved in musical interpretation, by studying a score and listening to a recording. I have tried to map processes dealing with listening and score reading through an experiment, in which students from the Malmö Academy of Music were presented with a novel piece of music. I have made some conclusions, for instance it seems as though there is a connection in the interpretation between musical complexity and tempo, and a connection between dynamics and pitch, moreover that the participants in this study seem to be affected by the interpretational practice at the Malmö Academy of Music. The study is qualitative in its design both regarding data collection and interpretation of data.

En stor andel av Sveriges enfamiljshus byggs i trä. Väggen i ett sådant hus är typiskt en skivbeklädd regelvägg. Målet med detta examensarbete är att studera lastkapaciteten hos träreglar i sådana väggar. Olika randvillkor gäller i de tre olika uppställningarna som studerats. Genom att variera randvillkoren undersöks vilken inverkan en syll och en skiva har för att styva av knäckning i veka riktningen.

This master thesis is about designing and dimensioning a boat for transport of caravan, car, trailer or ATV. Buoyancy and stability are important properties as the pontoonboat should also be able to serve as a workboat. Many of the vessels on the market today that is being used for similar purpose are stable enough, but their hull is often similar with barges and thus too slow. This work has been to construct a boat that has good stability but also has a hull that enables it to move faster, is more maneuverable and having a more attracting design than today?s barges.

This report describes how the process has evolved during the creation of a new web page forthe company Scandinavian Travel Agent DMC. The design methods that have been used aredescribed and also how parts of the webpage have been created by using the design methodresults. Our reflections around design and functionality are explained and how usability hasbeen our main focus during the master thesis. We also describe how it has been to work withan external costumer and how the tasks constantly have changed and been added as theprocess has continued.The background to this work is that AB Scandinavian Travel Agent DMC need to improve theircurrent web page. This to give the clients better needed information about destinations, butalso to stand out in the competitive travel business.

Immersion is a construct that measures how deeply engrossed a user is with any mediated situation. In the field of game design, immersion is a significant aspect of what makes a game enticing, and as such it is of pivotal importance to create and maintain it to keep the player's mind off the real world while inside the confines of a game framework. According to the GameFlow theory, it is one of seven key tenets of evaluating and implementing a successful game design. Yet, certain multiplayer online games are designed in a fashion that in some cases seem to break immersion, where the player is frequently put out of action, sometimes for minutes on end. In this study, using online questionnaires, we discover that players, despite claims otherwise, seem to be in several ways affected negatively by this breaking of immersion.

The degree project is performed at Metso Kamfab. The production is aimed on machines everything from handling of fiber to paper pulp. Metso Fiber and Kamfab are using Pro/Engineer for design and blueprint production. The processing department types the NC-programs in notepad on the basis of the blueprints, the CAD-dates that already is there are not used. The aim with the work is to study if Kamfab can use CAM-system for processing and production of programs for their NC-machines.

Ericsson develops a new stripline directional coupler. Its design is described in appendix B and differs from the directional couplers Ericsson uses in current products. The new directional coupler will be used for transmission power measurement in future UMTS 3G base stations.The most important parts of directional coupler theory are presented. It is necessary to study this theory to understand how the coupler works and how it should be designed to get good performance.Optimal directional coupler termination component values to get high directivity and broad directivity bandwidth have been investigated.The trim screws trim ranges have been studied.A simple analysis of serial production performance when termination component tolerances are taken into consideration has been done.The resistance components reactive (inductive/capacitive) characteristics at 2.14 GHz have been analyzed.The directivity performance limitations of the directional coupler, when Ericsson?s band pass filter is connected, are investigated.Design changes leading to better performance are proposed.

Syftet med denna uppsats är att analysera debatten som tog plats på hemsida Newsmill åren 2010och 2012 om intelligent design. Fokusen i själva textanalysen är en argumentationsanalys somtillsammans med kritisk diskursanalys skall utröna och förstå den maktförskjutning som går attfinna inom diskursen. Den kritiska diskursanalysen är byggd på Norman Fairclough. Analysen ärordnad kronologiskt och innefattar tjugotre artiklar allt som allt.Fokus i själva analysen ligger i att utröna och förstå hur debattörerna ställer sig till religion ochvetenskap i deras argumentation kring intelligent design. Här går att finna hur religion ofta förs insom begrepp i relation till personers emotionella agerande och överlag blir religion en belastning fördebattörerna.

This thesis deals with an iterative user-centered IT-development project in a bank setting. The aim is to present a solution for deployment of future Internet banking for small businesses. The project features a design of IT-related concepts and ideas with a strong emphasis on scenario-based design and the usage of patterns as a documentation tool.The project plan featured an iterative framework and was carried out by a group of designers in collaboration with a reference group representing the future users of the system. This group consisted of company managers and bank employees, all from the small town of Åtvidaberg in Sweden.The method used in the development process was Scrum. A total of three sprints were completed with user meetings at the end of every sprint.

This study examines the use of building modeling and energy simulations in the design process  of  a  building.  The  take-off  point  is  the  notion  of  energy  simulations  being needed early and throughout the building design process, and that the lack of energy simulations may be explained by the fact that they are time consuming and therefore often too expensive. A greater interoperability between software tools used by relevant disciplines,  such  as  the  architect  and  the  energy  specialist,  would  create  smoother workflows, which would reduce this cost and open up for more frequent and iterative energy  simulation  processes.  The  study  is  an  assessment  of  the  modeling  tool  Revit and  the  simulation  tool  Virtual  Environment  and  whether  they  can  create  smoother workflows, and make leeway for a more frequent use of energy simulations throughout the  design  process.  It  also  investigates  the  limitations  of  what  can  be  examined  by simulations in Virtual Environment. This will hopefully help clarify the future role of energy  simulations  in  design  processes.  The  method  is  a  trial  by  error  approach  of testing the two software tools by building and simulating a model. The results of these tests  show  that  the  workflow  is  not  optimal  (and  therefore  time  consuming)  for frequent  and  iterative simulations  throughout the  design  process,  but  it  also  reveals some  great  possibilities  of  what  can  be  performed  with  these  two  powerful  tools  at hand.  Further  development  with  regards  on  platform  independency  of  the  building information  model,  including  seamless  exporting  and  importing,  seems  necessary  to strengthen the future role of energy simulations..

The purpose of this thesis was to design an electrical system for use in a ballistic test at the Swedish National laboratory of forensic science (SKL). The detector unit would use four main parts: coilsystem, transmitter, reciever and indicator. The coilsystem would be based on a balanced system using three coils. One that creates a magneticfield and the other two will sense the differences when a metallobject is in the coilsystem. This report starts out by investigating possible solutions for this specific task followed by a description of the physics that the metaldetector use.

Denna rapport behandlar examensarbete utfört för industridesignföretaget Cate & Nelson Design. Företaget ligger i Eskilstuna och jobbar i huvudsakligen med möbeldesign och inredningsprodukter. Projektgruppensuppgift har varit att ta fram en ny möbel för företaget och arbetet har omfattat utveckling av hela produkten från idé till prototyp..