During the cultivation season there are a several cropping activities to carry out. At what time these activities are carried out is affecting the result and also on the economy of the crop production. As the production costs are high in potato production, it is important to keep an eye on the economy. Profitability is the most important factor in most crop production systems. If the costs are not covered, it is difficult to justify the production.

During the cultivation season there are a several cropping activities to carry out. At what time these activities are carried out is affecting the result and also on the economy of the crop production. As the production costs are high in potato production, it is important to keep an eye on the economy. Profitability is the most important factor in most crop production systems. If the costs are not covered, it is difficult to justify the production.

During the last few years the harwarder has developed from a prototype into a market product. Holmen Skog owns two harwarders and uses two more owned by entrepreneurs. In previous studies it has been shown that the harwarder was a slow and expensive forwarder. In this study the unloading at road-site was studied. The goal was to describe the differences in time consumption between unloading two-sided or single-sided (only from side of the road) and also the difference between unloading with three and four assortments in the carrier.

The economic prerequisite to many farmers in Sweden after the EU membership and the new agriculture policy has generated large demands on the farm management. Until year 2004 you got a grant based on what you had produced and not on consumer demand. In 2005 a new economic aid (Mid Term Revue) was introduced and the conditions has changed again. Due to this I have chosen to do a cost-benefit analysis on a case, to investigate if the present production is sustainable in the future. My conclusion is that the profitability is acceptable even if the farm has a high debt. But to make the production more profitable the products produced should be refined as much as possible at the farm, to get maximum economic return.

Cost allocation ? a study of how Swedish energy companies allocate costs between electricity and district heating in a combined heat and power plant District heating is today the most utilized alternative for heating in Sweden. In a combined heat and power plant (CHP) electricity and heat are cogenerated. The environmental and economic advantages with this kind of production are high. A problem in a CHP-plant is to allocate costs between electricity and heat since both products are generated in the same process.

Several technical solutions are ready to step forward as the new generation of propellant, and this report aims to explore the possibility of commercializing fuel cell cars. The report is based on current research and data from today's technology and engineering solutions that are estimated to be commercially realized before 2020.A mapping of today?s different fuel cell options has shown that the most suitable fuel cell option is the Proton Exchange Membrane Fuel Cell, which uses hydrogen as fuel. The report is focusing on a techno-economic well-to-wheel analysis of hydrogen and the energy balance and costs in a system perspective. The basis for this analysis consists of two centralized methods of production, steam methane reforming (SMR), and alkaline water electrolysis.

This report is a thesis work for a B.Sc. in Forestry exam at the School for Forest Engineers, SLU. The work was an assignment from Sydved Energy AB. The aim of the work was to compare the operational productivity between two kinds of forwarders for extraction of harvesting residues, one forwarder with a special compression device and one ordinary, slightly modified forwarder. Two sites were studied for each forwarder. The study shows that the annual production was about 11,000 m3 higher for the traditional forwarder. The cost for the traditional forwarder was SEK 0.9 lower per m3.

Optimizing energy systems is, in Sweden, as in many other countries, of growing interest. District heating systems are no exception. In 2012, 285 out of 290 municipals in Sweden had district heating in use and the majority of these systems have a higher return temperature than that which is possible with an error-free substation of day current technology. To, when possible, lower the return temperature is a way of increasing the effectiveness of the district heating system.This study means to investigate, through simulations and calculations, how big of a reduction in production cost a lower temperature in the city of Ystad?s district heating system would correspond to.

This study investigated the performance and cost of scarification with a tractormounted excavator. Due to variations in terrain conditions the performance variedbetween 0.08 and 0.11 ha/E15h and, with a machine cost of 366 SEK/h, the cost ofscarification varied between 3 330 and 4 750 SEK/ha..

The market is developing and a growing competition increases pressure on companies to maintain their competitive advantage. Working with cost savings is a way to enhance earnings in a short term but also in a longer perspective. Volvo Powertrain Production Köping has an overall goal; to reduce costs by nine percentages in three years. To achieve the goal, Volvo Powertrain Production Köping works with World Class Manufacturing where the Department of Processing Technology constitutes an important part.Volvo Powertrain Production Köping lacks a standard for how savings within the metal cutting tool area are to be calculated. This makes it difficult to control and monitor their business outcome but it also causes difficulties in controlling the tool suppliers? outcome.

The purpose of this essay is to identify costs for providing First-line and Second-line support, and then allocate these cost to different goods and services (cost objects) being supported. The thesis also intends to improve the overall cost awareness in IT settings..

When I got the opportunity to write this examination did I want to write about something that I both was interest in and also can use in the future. I think it?s going to be difficult to carry on the milk production with only 28 cows. I wanted to investigate the possibility to increase the herd of cows. I also wanted to compare this cost with a new cow house the cows where milked with a robot.

The purpose of this bachelor degree thesis is to analyze technical issues associated with an implementation of a low sloping trash rack with narrow spacing. A hydropower plant in Umea?lven was used as a case study. The basis for the study was a model where trash racks were dimensioned for inclinations between 25 and 45 degrees. Corresponding head loss, durability and water speed through the rack were then determined for each inclination.

Recent studies show that manufacturing companies to a larger extent use historical cost accounting in their internal accounts, at the expense of calculated costs. The explanation behind this is claimed to be that firms are subject to careful scrutiny by the stock market. Consequently, top management stresses the need of evaluating all parts of the firm from external accounting. However, lower management levels express a general concern that the incentive to invest in machines will decrease. This master thesis aims to investigate whether or not there is an objective reason behind this concern.

This report deals with issues related to construction waste. Building material that has not been built into the project is defined as construction waste. Cost of construction waste amounts to 4-12 % of the total cost of the project. Moreover, cost of construction waste is 1-3 % of the production cost. The aim of this study is to increase knowledge about the main causes of waste within the construction industry.