This master?s degree project concerns the combination of a multi dwelling passive house with solar energy for the generation of electricity and domestic hot water (DHW). Different alternatives with either solar thermal systems or photovoltaic (PV) systems are compared with two reference alternatives producing DHW from electricity or district heating. The economical comparison uses a life cycle cost (LCC) perspective based on the present value of expenditures for investment, energy and annual operating and maintenance.The energy yields from the solar energy systems were calculated by hand and with simulation software. Calculation and dimensioning of PV systems were carried out with a software called PVSYST.

This thesis analyses the cost accounting system KPP and its use within the Swedish health care. KPP is designed to calculate and assign health care costs to individual patients. This would facilitate evaluations and comparisons of the costs for certain diagnosis, patient groups or clinics with a different mix of diagnosis. The study investigates the following questions: 1. Does the KPP-model theoretically work as a cost accounting tool for health care purposes? 2.

Tomo Hugglink (TOMO Skog) is an innovation for harvest and transport of biofuels. The system consists of a truck, a chipping unit and crane mounted on a link and a wood chip trailer. The system works in such a way that the chipping unit is disconnected and placed on the site and wood chips are loaded directly into the wood chip trailer.The aim of this study was:- To examine the performance of the TOMO Hugglink system under different conditions such as the size, placement and quality of the pile.- To calculate the cost per raw ton for two vehicle combinations at different transport distances and to examine the effect of a reduction in set-up time and an increase in load weight.- To identify possible improvements with the TOMO Hugglink system.A time study was conducted within the thesis work to make it possible to determine production and time consumption. In the subsequent economic analysis the cost per tone at different transport distances was calculated for two different lorry concepts. Furthermore the effect of a reduction in set-up time and an increase in load weight was calculated.Under current conditions the utilization of the chipper is low and only 29 % of the total system time is occupied by chipping.

Title: The component approach - From the harmonization process as a background to the perception of benefits and costs as effects.Authors: Elin Börjesson & Emma KarlssonTutor: Titti EliassonKey concept: Harmonization, Component approach and Benefit/CostBackground: With IFRS for SME's as a basis, the Accounting Board developed K3 which shall apply from financial year 2014. Upon introduction of the K3 companies will be forced to apply the component approach. When K3 with the associated component approach went out for consultation it resulted in a debate where some actors opposed the imposition of a requirement and not an option. It was questioned whether the costs with the component approach would be greater than the benefit of the implementation.Formulation of the problem: How is the introduction and use of the component approach seen by different operators from a benefit-, cost perspective?Aim: The aim of this essay is find out how the introduction and use of the component approach is seen by different operators from a benefit-, cost perspective.

This thesis is a product development project that was performed at Alfa Laval Tumba AB. In the past Alfa Laval have manufactured gas separators for engines where gas flows were cleaned from oil. A new business area for this kind of technology has shown to be the manufacturing industry where oil mist has to be separated from the vented air. Therefore a new and bigger design is needed to be able to handle the greater gas flows. A product like that would be a strong competitor on the market when the maintenance would be low in comparison to today?s equipment.During the project several concept suggestions were developed using customer interviews and research as input.

This thesis investigated if a combination of increased under colour removal (decreasing the total ink limit), normal andincreased density and modern FM-screening could be used to provide a visually better print on uncoated and coated paperin comparison with AM-screening using the same conditions.Two different test groups (one with graphic background, the other with no graphic background) were asked to a visuallyassess the quality of the prints presented in a pair comparison using a reference image.The results show that the FM-screening did not obtain any significant visual difference in comparison with AM-screening,regardless of paper types and density levels. In general however, prints on coated paper were graded higher..

With the elevated oil prices of today it is necessary to look for other heating alternatives. If the oil price continues to develop in the same way it has done the last years it will soon be impossible for many producing garden companies to survive. The purpose of this diploma work is to compare three different fuel options in order to find the most economic one considering the conditions of Katrinebergs Handelsträdgård AB. In relation to oil it is profitable to change to any of the three alternatives: wood chips, wood pellets and grain. The most profitable option is to change to wood chips. This alternative has a payoff time less than three years and after that the annual saving compared to the oil is relatively high. The annual cost is 65 % of the cost of the oil alternative.

Since 1996 the Swedish households have ten folded their volume of loans for own homes that is attached to a floating interest rate. Also in 1996 the Swedish electric market was deregulated. These two facts have increased the volatility in the household expenses for these two commodities. This thesis studies the risk for homeowners attached to the exposure against the electric and the credit market. The risk model used is Cost-at-Risk which is usually used by public authorities for analysing the risk involved with national debt.

As IT service departments in organisations are becoming more complex and customised, the indirect costs are increasing in relation to the total costs. The difficulty of fully estimating and identifying the spread of the cost in the IT service department is increasing. As a result, firms tend to budget the business unit as a total cost rather than as a spread of defined costs. In order to deal with this challenge an ABC calculation will be applied. The Time Driven ABC model will be conducted in OMX´s Servicedesk unit within the IT services.

Syftet med studien var att undersöka huruvida utsattheten för ?sunk cost-effect? och förankringseffekten ökade vid intuitivt processande jämfört med analytiskt processande. Deltagarna i studien var 78 studedenter vid psykologiska institutionen vid Göteborgs Universitet. Datainsamlingen gjordes genom en pappersenkät. En 2 × 2 - vägs ANOVA avseende bias och process gjordes för både ?sunk cost effect? och förankringseffekten i en mellanindividdesign.

This report provides a comparison between the products cellular concrete, foam concrete and LECA concrete. The questions to be answered during the work is how the cellular concrete stands up in cost terms to the existing competitors on the market, how the concrete products differ in design work, and in which situations the concrete varieties are preferred to use.Cellular concrete is a variant of ordinary concrete, with the difference that the ballast is exchanged from stone materials to expanded polystyrene beads (EPS). This substitution gives a product with higher insulation values but lower weight than ordinary concrete.The work was carried out by designing a survey which was sent to two hundred randomly chosen companies across Sweden, to see the building industry?s opinion of the product cellular concrete. The survey showed that cellular concrete was equals its competitors in terms of price, while the product was said to be more flexible, quicker and easier to cast.Then some of the companies, who participated in the survey, were interviewed to see more carefully, how the price, the workmanship and the time for casting and dehydration differed between the products.

Sweden?s District councils and Country councils are in itself to a large extent responsible for the state financed welfare. Because of this, Sweden has a contribution- and adjustment system. The reason for this system is to create equal chance, for all District councils and Country councils, to be able to give the citizens service independently of their income and non-influential structural differences. The adjustment is built upon the so-called standard cost method, which contains four different parts.

AbstractThe assignment were assigned by Camatec Industriteknik AB. Camatec is a Karlstadlocated consulting company, they make everything from pilot studies to complete projects in mechanical design and calculation. They even have their own patented product, Camcoil. It is a winder for steel strips and is used for example with hardening of the steel strip. The assignment has been to solve the problems encountered by some customers within this product.

In Uppsala, Sweden, Vattenfall has a combined heat and power plant. On the premises there is an engineering workshop with old fluorescent and mercury lamps that need to be replaced. This provides a great opportunity to save energy and money by installing more efficient lighting. The main purpose of this study was to present two functional and energy efficient lighting systems including control system. The lighting systems were designed by investigating the working environment, measuring illuminance and by simulations in the software DIALux.

This paper is the result of a case study conducted at Uppåkra Mekaniska AB during the spring of 2006. The task that was presented by Uppåkra was to develop a basis for a decision for the planning activities at the company, so that in the future they can create lot-sizes which are based upon a total cost perspective. Total cost in regards to lot-sizing is defined as the sum of the administrative reordering costs and warehousing cost per stock keeping unit.To collect data a series of interviews and observations were conducted. This data was then used during the lot-sizing simulation and analysis. The 15 units that the simulation was conducted on were grouped into three item classes depending how many different machine setups they required during the production process.