Highland Group AB was helping a customer of theirs to create an All-Terrain Vehicle (ATV), a project Highland has never been involved with before. For the wishbone arms of the wheel suspension, traditional manufacturing methods and tubes with cylindrical or square shaped cross section was preferred. We performed a simulation where the ATV was driving on a bumpy road too see the forces involved. With the results we proceeded to calculate the strength of the concepts to find out which is best suited for the tough environment in which the ATV is used. The concept that turned out to be the best was a wishbone made of circular cross section, which had good structural strength and did fulfill the demands that we required for the construction.

This report is on concrete work during the winter and is implemented on Peab?s behalf. The assignment was to describe the differences between a summer- and a winter casting. While it shows the complications that exists, it also show what aids are available, both electronic via computer and physical aids.The information that I have developed is originally from theory in books, information on the internet as well as practical experience from knowledgeable people that works in construction output. Other theories are those I have learned throughout the education to become a construction engineer, including all oral sources over the years.The results I have come up with, I hope will be able to help future construction projects in the planning phase of a winter casting.

Virtual communities are a phenomenon that is becoming more common as the information technology comes with in reach for the general public. This report will bring the theories and construction of a virtual community together. The purpose of this report is to describe the different theories that have emerged from the research within this field and to examine the work procedures that have been used during the development of a site for a MDA-community. The MDA-website is a homepage on the Internet that was developed to bring the students closer together. The report describes the work of the project group, why the website was not completed and at the end the theories are looked at on the basis of the construction of the website..

The Swedish pulp and paper industry meets higher demand for energy efficiencyi mprovements with increasing energy prices and changes in the Swedish renewable energy certificate system. One action of energy efficiency improvement is by using secondary heat, that otherwise would have been treated as waste heat, for use in a system with lower temperature demands. The aim of this Master´s thesis is to identify possible secondary heat sources in a typical Swedish pulp and paper mill and to investigate what economic benefits the secondary heat will provide when being used for pre heating of wood chips to a kraft digester.The Master´s thesis focuses on three secondary heat sources; dry warm air, warm water and moisture saturated warm air located inside the pulp or paper mill. Two types of kraft digesters are simulated within this study, a typical Scandinavian digester and a modern twin vessel steam phase digester.Due to quality aspects and low temperature level drying is the drying technology with dry warm air rejected. Using warm water in direct contact with wood chips increases the quantity of water to the evaporation plant and thus reduced pulp or paper production and is therefore also rejected.

AbstractHeadline: Young trouble and teenage love (Fjortisgrubbel och tonårskärlek)Number of pages: 37Author: Annika IlmoniTutor: Amelie HössjerCourse: Media and communication CPeriod: Autumn 2007University: Division of Media and Communication, Department of Information Science, Uppsala UniversityPurpose/aim: The purpose of the work was to produce a comparing study of two Swedish teenage films from different periods of time, 1970 and 2005. An analysis was to be made of how love between teenagers as well as the heterosexual relationship in general was depicted in each of the films and further investigate the gender construction in both films.Material/method: With the intention of narrowing down the complexity and make the evaluation more lucid 5 scenes from each film were used for comparison, these were chosen through the Anglo Saxon dramaturgy. To make the scenes more comparable 4 factors were used for analysis in each scene, these were: clothes, recreational activities, behaviour and environment. Beside the above given factors the heterosexual relationship were analysed and compared in each of the scenes through the theory of dominance in dialogue.Main results: The gender construction occurs obliviously in the older film from 1970 while taking place in a more conscious way in the film from 2005. Further on the heterosexual relationship is perpetually depicted in the 70?s film with a submissive girl and predominant boy, the same dominance is easily seen in the more recent film but with a higher rate of equality as the girl is portrayed as the dominant character in almost half of all scenes.

There is a lot going on in the construction business right now. It feels like everywhere you turn there is a building sight. Furthermore the business is heading a generation change and the need of recruiting new construction engineers is huge. How is the business going to handle the transition that they are facing? The question has been in progress for at while and I wanted to find out what the current students feel about taking the step into the working life and replace the veterans.A research is made about student?s opinion about their education and future work life.

Syftet med examensarbetet är att hjälpa ett företag med att införa standardlittera för deras prefabricerade betongelement som ingår i deras Konceptet. Införandet av standardlittera ska resultera till att återfinna och gruppera deras betongelement i CAD-systemen. We did our thesis project at one of the most prestigious Swedish construction companies. We have examined the possibilities of doing sandwich elements to standard elements which would increase the degree of industrialization. The company has developed a concept that is based on a more refined process of industrialization.

Sammanfattning Detta arbete beskriver de studier som utförts vid implementering av Last Planner planeringsmetod, i projektet att bygga LKAB:s flotationsanläggning i Svappavaara. Studien har bedrivits vid institutionen för Samhällsbyggnad i Luleå och LKAB:s malmförädlingsverk i Svappavaara. Arbetet inleder med en granskning av litteratur om teorier och grundtankar om Lean Construction. Filosofin bakom Lean Construction bygger på att avlägsna alla processer som inte skapar mervärde för kunden. Tankegångarna kommer från den Japanska bilindustrin och då främst från Toyotas framgångsrika produktionssystem TPS.

The construction market has, as a result of the crisis in Europe been uncertain in recent years. During the year 2013, the construction will be stabilized, in particular Finland. The geographical proximity between Sweden and Finland and similarities in cultures and climates makes Finland a coveted market for many Swedish companies.Differences in national regulations and guidelines, which are produced by the authorities in different countries, are examples of barriers that may hamper the process, including for Swedish villa suppliers, to establish themselves on the Finnish market. It may be useful when facing a new export drive, to look up what similarities and differences there are between the countries building codes, to prevent mistakes and unnecessary costs to the project work..

To challenge the competition within the construction business there are requirements ineffectiveness and use of operating computer based programs and work-methods. Thecomputer based programs are continuously improved and can at some point be the start of anew work-method. The work-method of tomorrow can be Building Information Modeling(BIM).This Master of Science Thesis gives an understanding in what BIM is and what therequirements for Sweco Theorells are in a future BIM-use as a consulting-firm. Theunderstanding is presented through a study of theory within the subject. The way of thinkingand acting among different disciplines and individuals within the building process isexplained through an interview study.The term BIM is regularly used.

According to recent statistics the construction industry is responsible for the largest waste discharges of both dangerous and non-dangerous waste, when disregarding the "non-dangerous" amount of granite waste produced by the mining industry and the waste produced by the pulp and paper industry. Preventive work within waste management is an ongoing practice so to be able to reduce negative environmental effects. One of the most common actions for the companies to take is to separate the different kinds of waste from one another at the construction site. Although by working with the problem in earlier stages of the process a large amount of the waste could already have been reduced.Companies in the construction business that are actively working to decrease environmental impact in their operations often use an EMS (Environmental Management System). By using environmental management as method the company can manage their environmental work so that actions can be taken where they are needed the most.

The aim with this thesis is to study the risk management in construction projects at the Swedish Road Administration, SRA. Furthermore, the aim is to find the effects of the risk management. The theorem of this thesis is that the positive effects of the risk management in construction projects create additional value to the project. These additional values are that the project itself becomes resilient and that the project goals are achieved without any significant disturbances.This thesis shows that the risk management in construction projects do not follow the guidelines set out by the SRA. This is due to a lack of education in the method and a difficult method all together.

This report is founded in lack of knowledge concerning the design and layout procedureduring a new engine room construction.The prime question is how the engine room takes its form from idea to construction and whathappens in between. We want to give the reader a better understanding in how the work isdone and why it is designed the way it is concerning layout, ergonomics and safety. Duringthis report we will enhance the knowledge concerning regulations and rules that are of greatsubstance such as SOLAS, Swedish Sjöfartsverket and IMO.By contacting the parties involved in the process in newly designing a vessel and its engineroom, we will assume their approaches and experiences. We will study the work progressfrom planning to construction of a vessels machinery spaces. We will with the help ofinterviews with interested parties get an idea of the approach and also compare the finishedproduct a bit depending on company size and resources.The investigation resulted in a good basis for how a ship engine room design takes shape andwhich aspects are taken into account, however, we found that the existing rules concerningengine room layout was very vague and was seen as the most recommendations.

This report addresses the growing need to adapt the medical healthcare to the new possibilities that can be accomplished by incorporating a web aspect to the personal treatment plans of patients. It describes what implementations that need to be considered in order to successfully convert to a partially web-based treatment.The report also reflects the potential economical gain that can be made by keeping the communication between the patient and the doctor frequent. It also takes into account the personal gain to the patient by increased feedback and easier ways to communicate with their attending physician and thereby increasing the quality of their healthcare and service.The construction of a prototype of the system required is also included in the report as a description of construction and functionality of the prototype along with results and estimated outcome..

Balcony Art is an idea for a new kind of furniture group for those who have limited space on their balcony. This report will discuss conceptual and part of primary construction of the chair and table for use on balconies, how the products developed from an idea to primary, preliminary products.In the conceptual design part, the report will discuss how product requirements and specifications are developed and how these controls the design.In the primary construction, the report will discuss the products journey from sketch to functional CAD models and how the products of individual parts are designed and how the durability calculations affect the design..