This report is a bachelor thesis work within the field of Product Development and is also an assignment for Thule Sweden. The work has been performed by Niclas Tjäderborn and Christian Holm, students at the Mechanical Engineering Program with major in Product Development and Industrial Design at Jönköping School of Engineering during spring the semester of 2009.The thesis work concerned the development of a new wheel holder for bike carrier for Thule Sweden. The background to the project was that the initiator wanted a more user friendly wheel holder with better design than those available on the market. The wheel holder is able to be implemented on one or several of Thule?s current wheel holders.

Highland Group AB was helping a customer of theirs to create an All-Terrain Vehicle (ATV), a project Highland has never been involved with before. For the wishbone arms of the wheel suspension, traditional manufacturing methods and tubes with cylindrical or square shaped cross section was preferred. We performed a simulation where the ATV was driving on a bumpy road too see the forces involved. With the results we proceeded to calculate the strength of the concepts to find out which is best suited for the tough environment in which the ATV is used. The concept that turned out to be the best was a wishbone made of circular cross section, which had good structural strength and did fulfill the demands that we required for the construction.

This report describes the planning and the accomplishment of the final diploma workat the study program Mechanical Engineering, Department of Engineering Sciences, Uppsala University. Two students carried out the diploma work at GE HealthcareHusbyborg in Uppsala.The aim of the diploma work was to develop and improve existing processequipment for 11C-radiochemistry in PET. The process equipment was to be dividedinto smaller independent modules to make it more flexible. Part of the existingprocess equipment is an oven that is supposed to perform a specific chemicalreaction. One of the main goals was to study and improve this oven.The work could be divided into three main phases: 1.Present concepts for one module, and interface between different modules.

This report is on concrete work during the winter and is implemented on Peab?s behalf. The assignment was to describe the differences between a summer- and a winter casting. While it shows the complications that exists, it also show what aids are available, both electronic via computer and physical aids.The information that I have developed is originally from theory in books, information on the internet as well as practical experience from knowledgeable people that works in construction output. Other theories are those I have learned throughout the education to become a construction engineer, including all oral sources over the years.The results I have come up with, I hope will be able to help future construction projects in the planning phase of a winter casting.

Detta kandidatarbete är utarbetat på Blekinge Tekniska Högskola under våren 2002. I utredningen har vi jämfört röstigenkänningsprogram under en treårsperiod, program från 1999 och program från 2002. 1999 års test visade på programvaror med lång träningstid, enkla gränssnitt, stor känslighet för bakgrundsljud och låg användbarhet. Vid arbetsstart förväntade vi oss inte att hitta någon större förändring i användbarheten hos dessa program 2002, då röstigenkänningsprogram inte verkar ha stor användarskara. Utifrån följande hypotes har vi genomfört arbetet: Vi vill med vår undersökning bevisa att användbarheten inom röstigenkänningsteknologi inte har förbättrats under perioden 1999-2002. Vi har för avsikt att med hjälp av test utförda på program och demoversioner bevisa vår hypotes. I enighet med bifogad testspecifikation har vi utfört testerna. Många företag har utvecklat sina produkter och gjort dem bättre.

The aim for the project was to develop a risk analyse tool for measuring the fire safety level in Cultural Heritage buildings of Visby, Gotland. In 1995 Visby were taken into the Unesco:s World Heritage List with the explanation ?Visby is an outstanding example of a Northern European walled Hanseatic town which has in a unique way preserved its townscape and its extremely valuable buildings? One of the demands for the tool was that it should be easy to use and result into a ranking level in examined buildings. The user of the tool is recommended to be personnel in the fire department. To develop the tool a Multi Attribute Decision Making (MADM) method was used.

The main objective of this thesis is to examine the situation concerning information technology, computers and information resources for university students at a selection of universities, and their libraries, in Sweden. Another objective is to compare this situation to what is stated in policy documents on the subject, and if the size of the university matters regarding resources. The thesis starts with a discussion of several authors, Frank Webster, Paul F. Burton and Lars Qvortrup among others, and their views on the information society. These range from whether we are living in it, are in a transition period or are still in the Industrial Society.

Purpose: The objective of this study is to illustrate how participants in leaderless based projects communicate with each other. Several studies have focused on technology-supported projects, such as open source projects, with an established project manager and goal. There is a lack, to the best of our knowledge, in studies that deal with the communication pattern in a leaderless computer supported collaborative project.Method: We have chosen to use a quantitative method where we systematically group several messages according to their content. This method was used in a similar study to illustrate the communication between participants involved in an open source project. We have taken the same Kripendorff based method and adapted it to our study by adding more descriptive variables.Theoretical perspectives: Manuel Castell discusses the aspects of a new communication power that is rooted in the individual as part of a larger creative audience.

This report describes the planning and the accomplishment of the final diploma workat the study program Mechanical Engineering, Department of Engineering Sciences, Uppsala University. Two students carried out the diploma work at GE HealthcareHusbyborg in Uppsala.The aim of the diploma work was to develop and improve existing processequipment for 11C-radiochemistry in PET. The process equipment was to be dividedinto smaller independent modules to make it more flexible. Part of the existingprocess equipment is an oven that is supposed to perform a specific chemicalreaction. One of the main goals was to study and improve this oven.The work could be divided into three main phases: 1.Present concepts for one module, and interface between different modules.

In this project we have used the theory of analytical mechanics to derive equations of motion for complex mechanical systems in order to study their behaviour over time. Even if the theory provides powerful tools to tackle tough problems which would be very hard to solve by methods of Newtonian mechanics, you are still relatively limited without running any computer simulations. One realises that in a faster rate it will be an incredibly difficult task to find an analytical solution when the degrees of freedom increases. Even if one would succeed to derive the equations, one still has to solve them to get the information of the systems behavior. Of experience one knows that the equations in general are nonlinear and hence must be integrated numericaly.

AimThe purpose of the study was to investigate how upper secondary school students experience performance demands during their physical education and health classes (PE-classes). The questions were as following: Are there differing perceptions between the sexes whether students experience performance demands? In what situations do the students feel that the demands on their performance are high during PE-classes? Do the students experience of demands on performance differ whether the physical education and health teacher is male or female? Do students feel unfairly treated by the physical education and health teacher during PE-classes?MethodSeven upper secondary schools in Stockholm?s administrative district were randomly selected to participate in the survey. The principals were contacted for further information and to set a date for performing the survey. The project leaders were present during the days the surveys were taken by students in the social science and natural science programs.

JavaScripts popularity is increasing and the number of libraries too. This report focuses on well-known software metrics in complexity, maintainability and different size-metrics. A few different JavaScript libraries are compared and analyzed. The result shows that there are indeed differences, mostly in size- and complexity-measures where some functions are implemented with a higher complexity..

This major project in Building Engineering has its focus on inquiring into what methods has been used in the planning process of the residential buildingLjusbojen 1. This project has been conducted in cooperation with Kadesjös Ingenjörsbyrå AB, an engineering contractor firm which also acts as the property developer. Initially several different general methods for planning residential buildings have been presented. After the methods from the process of building Ljusbojen 1 has been analyzed compared to the general methods presented in part 1. This shows what the determining factors are during the planning process; factors such as cost, quality, time management, know-how and environmental issues.

This report is a bachelor thesis work in the field of product development and design. The assignment has been to develop a solution for roof racks, normally used for cars, to fit on the open trailer models FS1425 and Alugance. The project was implemented by Johan Andersson and Victor Karlsson, students at the Mechanical Engineering program with a focus on product development and design at Jo?nko?ping?s school of Engineering, in spring 2012.The client wants to use transport solutions in the same way as roof racks on cars. The user of such a product is assumed to desire simplicity, safety and an attractive design with an appealing price, which has been a challenge during the thesis work.Pre-studies have been conducted to examine the potential competitors and gain knowledge in the research area.

This thesis aims to develop a control system for measuring electromagnetic compability (EMC). This has meant that a controller designed around an ATmega8 microcontroller has been manufactured and programmed. It has also meant the development of a comprehensive control software in the program MATLAB. The control system has been tested with satisfactory results and can now, monitor and control measurements of the EMC-type..