The main purpose of this project was to make a survey of the steam and electricity consumption at Akzo Nobel Functional Chemistry AB and give suggestions of how to minimize them. These three different areas were focused on. First to make a survey of all the most important consumers, second to find the electricity consumption of the air compressors and the amount of waste heat produced from them. The third area was to calculate a model of how much fresh water that is used during a cooling sequence in the water based heating/cooling system of the reactors and give a suggestion of a suitable reuse for this water.The main result is a total survey of the energy consumption in steam and electricity. The survey shows that the second largest group after drying is heating of ventilation which gives big potentials of reducing the total steam consumption if there is a way of being self supporting in ventilation heat.

AbstractThis master thesis was performed at Scania transmission department in Södertälje, where the manufacturing of gears is done. Today a large amount of manual handling is performed between the machining and the hardening process. Most of the manual handling is done at the heat treatment department. The purpose of this master thesis is to give a suggestion on how to reduce or eliminate the manual handling at the heat treatment department. The possibility to use the same packaging throughout the processes will also be investigated.

The Rya power plant in Borås produces district heating, district cooling and electricity. The plant is owned by Borås Energi och Miljö AB and is run by Dalkia Facility Management AB.In order to get the best heat exchange from the district hot water a pair of twin pumps and a turbine circuit pump are used as return pumps. Turbine circuit pumps are used to increase the pressure through the heat exchangers at the power plant. The pumps are in use when the flow is over 2 000 m3 h-1 and during the summer when re-cooling is used to improve the effectivens of the heat boilers.Since the pumps, that are parallel connected, rotating at a fixed rate per minute, the pressure is regulated with regulating valves. This report shows that during the 4,300 hours that the pumps where in use, energy corresponding to 590 MWh was wasted.

AbstractThis master thesis was performed at Scania transmission department in Södertälje, where the manufacturing of gears is done. Today a large amount of manual handling is performed between the machining and the hardening process. Most of the manual handling is done at the heat treatment department. The purpose of this master thesis is to give a suggestion on how to reduce or eliminate the manual handling at the heat treatment department. The possibility to use the same packaging throughout the processes will also be investigated.

As a company it is required to work with strategies to minimize costs such as packaging and logistic costs. The increased market of industrial produced wooden buildings results that the time and the cost which the packaging of prefabricated building elements consume, is experienced to be in greater need of development than before and demands a better solution. The aim with this dissertation was to discover how the development of the handling of the packaging can improve the packaging process. The goal was to present improvement proposals for a simplified and thereby a more efficient production in time and cost perspective.The packaging process which includes packaging, handling, storage and transport were studied. Interviews were made with participants from the market for manufacturers of wooden houses and a case study was made at the company A-hus.

AbstractClimate and environmental issues are of paramount importance. Researchers agreethat we must all contribute to a reduction of gases that contribute to climatechange. Energy consumption must decrease within all sectors and the promotionof renewable sources of energy must be introduced.Each sector should aspire to decrease its energy consumption. Energyconsumption is strongly linked to waste gases that contribute to climate change.Passive houses are a part of the construction industry's methods to attain energyconservation.Passive houses are derived from low energy houses and super insulated houses. Apassive house is intended to obtain heat from the inhabitants and through theiractivities.

AbstractThis master thesis was performed at Scania transmission department in Södertälje, where the manufacturing of gears is done. Today a large amount of manual handling is performed between the machining and the hardening process. Most of the manual handling is done at the heat treatment department. The purpose of this master thesis is to give a suggestion on how to reduce or eliminate the manual handling at the heat treatment department. The possibility to use the same packaging throughout the processes will also be investigated.

The objective of the essay was to identify the nursing care required by a dog suffering from heat stroke and how to educate and advice the owners how to start treating their dog and prevent the condition from occurring in the first place. The essay is based on a literature study. Several databases were searched for scientific research to try find answers to the issues. Keywords concerning the subject were used and mixed in different combinations to sort out the suitable studies. The results of the study indicate that the dog should be cooled by the owner directly after detection. The most crucial issue is to reduce the body temperature as quickly as possible or the morbidity will worsen.

This report describes the work of developing a specification of requirements for Waste Heat Recovery Units. The main part of the paper describes how the work with the specification of requirements has been performed. One specific question to be answered is:What are the customer?s demands in case of properties for the Waste Heat Recovery Units and how is that information collected as an order documentation to suit the business area Oil & Gas?The report begins with a description of the assignment and continues with the aim and background. A theoretical part describes the different areas and methods that have been important during the process.

Who runs the development? A comparative study of the construction of residential buildings in Nacka and Södertälje.The aim of this study is to identify actors involved in the initiation and implementation of residential house construction in two Swedish municipalities. This means who is taking initiative for new residential buildings, who affects the planning process, who finances these new buildings and who builds them. By exploring empiric material from the municipalities of Nacka and Södertälje, the above questions will be answered and by referring to pluralism, growth machine theory and regime theory a link to general theories of political science is made. The results found show that the analysed municipalities have quite different possibilities for acting and that these backgrounds are also important for which actors will take initiative for new residential buildings and which actors will be allowed to state their opinion during the planning process.

The aim for the project was to develop a risk analyse tool for measuring the fire safety level in Cultural Heritage buildings of Visby, Gotland. In 1995 Visby were taken into the Unesco:s World Heritage List with the explanation ?Visby is an outstanding example of a Northern European walled Hanseatic town which has in a unique way preserved its townscape and its extremely valuable buildings? One of the demands for the tool was that it should be easy to use and result into a ranking level in examined buildings. The user of the tool is recommended to be personnel in the fire department. To develop the tool a Multi Attribute Decision Making (MADM) method was used.

The Swedish pulp and paper industry meets higher demand for energy efficiencyi mprovements with increasing energy prices and changes in the Swedish renewable energy certificate system. One action of energy efficiency improvement is by using secondary heat, that otherwise would have been treated as waste heat, for use in a system with lower temperature demands. The aim of this Master´s thesis is to identify possible secondary heat sources in a typical Swedish pulp and paper mill and to investigate what economic benefits the secondary heat will provide when being used for pre heating of wood chips to a kraft digester.The Master´s thesis focuses on three secondary heat sources; dry warm air, warm water and moisture saturated warm air located inside the pulp or paper mill. Two types of kraft digesters are simulated within this study, a typical Scandinavian digester and a modern twin vessel steam phase digester.Due to quality aspects and low temperature level drying is the drying technology with dry warm air rejected. Using warm water in direct contact with wood chips increases the quantity of water to the evaporation plant and thus reduced pulp or paper production and is therefore also rejected.

This master thesis project at KTH is performed in the Mechanical and Aerospace Engineeringdepartment at University of Florida (UF). The thesis is a small part of a gas turbine researchproject where a vapour absorption refrigeration system (VARS) and a high pressure regenerativeturbine engine (HPRTE) are integrated together. The main objective is to build a computermodel of the VARS. The computer model is supposed to be used to analyse the off-designperformance of the VARS and should also be easy to integrate as a subroutine in a more complexsystem model. To model the VARS some knowledge of the absorbent/refrigerant mixture had tobe well known, in this case a mixture of ammonia and water.

Mobila verksamhetslokaler erbjuder flexibel lokalförsörjning som alternativ till permanent utbyggnad, eller under tiden som befintliga lokaler renoveras eller byggs om. Denna flexibla möjlighet används dock i en ganska liten omfattning på marknaden. För att öka lokalernas användning finns det därför ett behov av en marknadsundersökning som identifierar de faktorer som kunden värderar.Utredningen syftar till att få fram vad kunden värderar då han eller hon hyr och/eller använder en temporär lokal, och möjligen identifiera nya element som inte finns i marknadens utbud.För att få fram värderingsfaktorer har en litteraturundersökning implementerats och samtidigt har 13 personliga intervjuer genomförts. Intervjuer skedde med personer som använder dessa lokaler och parallellt de som tecknat kontrakt för att hyra dessa lokaler. Studieobjekt är kontor, skola och förskola..

In this work we have compiled results from various studies concerning medical conditions that may possibly be avoided by castration and the effects that may occur after castration of the healthy bitch. The work is a literature review but it also includes a summary on the age recommendations for castration of the healthy bitch, castration before or after the first heat and the castration method most commonly used of ovariohysterectomy and ovariectomy. The summary is based on a questionnaire answered by personnel from 20 veterinary clinics and animal hospitals evenly distributed throughout Sweden.The summary showed that ovariohysterectomy was the most common method of castration and the recommendation in age ranged from 6-12 months. Regarding castration before or after the first heat 75% of the veterinary clinics and animal hospitals answered that they recommended castration after the first heat. Literature study shows that there are both advantages and disadvantages of castration of the healthy bitch and that it therefore is important that each bitch get a personal and individual evaluation before a decision is taken concerning a castration..