In this report listed buildings, according to the Swedish Heritage Conservation Act, have been studied with a focus on cases where economical compensation has been given to the owner of the building and cases where the listing of the building has been appealed by the owner. In order for a building to become listed it needs to be particularly valuable from a cultural and historical standpoint. The listed buildings are protected through a list of regulations that determines which parts of the building can or cannot be changed, what methods and materials should be used for changes and repairs, and how the building should be maintained. These regulations should as far as possible be formulated in agreement with the owner, but a building can become listed against the owners will. To decrease the damage this causes the owner he can in some cases have the right to economical compensation. There is also a possibility for the owner to appeal the listing of the building.

This report is about planning a demolition. The purpose of this report is that it should become a base for a demolition of house J at the Academic hospital in Uppsala, and also to make general help for planning a demolition. This report also contains a part about how a change in the work environment affects general people. The work started with studies of literature and design of the general part of the report and then continued with a practical study of house J. From the experience of the first two parts of the report a general help for planning a demolition was shaped.

The Swedish building stock accounts for nearly 40 percent of the total energyconsumption in the country. Properties built today are likely to last for 100 years orlonger. This places high demands on long-term and smart energy solutions that willkeep the future Swedish building stock energy consumption at low levels. This thesishas focused on examining how the energy performance of buildings is affected bydifferent choices of window types in different cardinal directions. The objective wasto obtain a basis for recommendations on how window properties can be optimizedfor different types of buildings and orientations.

The building industry are currently going through a huge alteration. The introduction of BIM (Building Information Modeling). Which also implements a lot of new ways of solving problems that building modeling can cause. This report is written for Uppsala University in cooperation with Temagruppen in Uppsala. However, it contains a comparison between two different systems that checks building models.

This report deals with prefabricated bathrooms and the advantage, during the production process, they have compared to ordinary produced bathrooms.The work is done together with the building company JM. The common task is to investigate if the manufactures, in spite of standardized design can meet the concept of JM, i.e. high flexibility and adjustment towards the customer. In JM they are doubtful to the method, as they did not yet worked with prefabricated modules and think that the choises for the costumer will be limited.There will be a short resume of the progress of the bathrooms and its importance as sanitary and wellbeing.The recent problems with damage caused by damp in bathrooms. Have resultade in regulations.

It has now passed two years since the new site- and construction law, PBL, went into force. It replaced the previous PBL applicable since 1987, and it involves relatively large changes in many different areas of the construction sector. The ambitions of the new law are for instance to simplify and clarify the legal text, increase efficiency in the permitting processes and improve the quality of construction. To achieve this, a variety of changes was made. Some of the most important are: inserted deadline in the processing of building applications, extended assessment of building applications, revised rules about controlplan and quality manager, a certificate is required to start and end the project, an additional meeting is inserted and the construction management of the municipalities will have to do a mandatory visit at the work scene.

Bygglovsprocessen är en vital del i den totala byggprocessen eftersom ett bygglov är nödvändigt i nästan alla fall av nybyggnation och större renoveringar. I dagens samhälle där byggprocessen är under utveckling och allt större tidspress finns så är bygglovsprocessen ofta en flaskhals innan bygget kan påbörjas. Därför behöver bygglovsprocessen utvecklas för att bli effektivare.Syftet med denna undersökning att utreda vad tidigare kunder hos Stadsbyggnadskontoret (SBK) Göteborg anser om bygglovshanteringen. Utifrån de resultat som erhålls presenteras vilka delar i bygglovsprocessen som kan förbättras och effektiviseras. Dessutom ges förslag på förändringar för att uppnå detta.Kundundersökningen genomfördes med en enkät som skickades ut via e-post till kunder som fått godkänt bygglov i februari 2014.

The author has, with the help of AK Consultancy Indoor Air AB, formed a series of questions regarding moisture problems in buildings and how these are handled in extreme climates with high temperatures and a high relative humidity. Furthermore to analyse and indentify key material that makes a construction safe against moisture problems. Ventilation, AC and the choice of materials have in a later stage of the thesis been investigated to enhance the knowledge of moisture protection. The research for this report includes measurements on existing buildings, calculation models on the building envelope for analyses and the ingoing materials of the envelope. The health aspect of moisture problems related to ?sick building syndrome? has been included and interviews have been conducted to gather relevant information.A study of the American system, ASHRAE, American Society of Heating, Refrigeration and Air Conditioning Engineers and the standards used in Singapore has been made to highlight the difference.

In this report listed buildings, according to the Swedish Heritage Conservation Act, have been studied with a focus on cases where economical compensation has been given to the owner of the building and cases where the listing of the building has been appealed by the owner. In order for a building to become listed it needs to be particularly valuable from a cultural and historical standpoint. The listed buildings are protected through a list of regulations that determines which parts of the building can or cannot be changed, what methods and materials should be used for changes and repairs, and how the building should be maintained. These regulations should as far as possible be formulated in agreement with the owner, but a building can become listed against the owners will. To decrease the damage this causes the owner he can in some cases have the right to economical compensation. There is also a possibility for the owner to appeal the listing of the building.

Bachelorprojektet behandlar arkitekturskolans lokal pa? O?stermalmsgatan 26, Stockholm. Skolverksamheten flyttar snart upp pa? Campus och skolan kommer att fa? en ny funktion. Projektet kopplar samman till en uppsats skriven om Daniel Libeskinds process, metod och symbolism och kopplar till skolans kvalite?er sa? som fo?rma?ga att provocera, fo?rha?llande till platsen, funktion och fo?rha?llande till staden.Utifra?n na?mnda aspekter konstrueras tva? delmoment som sedan ha?rleder formgivningen och den vidare omprogrammeringen av skolan till kontor, offentlig verksamhet och bosta?der..

The topic of our thesis is Packaging Design as a Brand Building Tool and we are presenting the Scandinavian perspective. We found the topic interesting because, from a theoretical point of view, we identified a scarcity in research focusing on packaging design as a brand management tool, and from a practical point of view, we found out that businesses use packaging design at different levels in their communication efforts. Thus we wanted to provide both academia and business world with a clear picture to what extent and how businesses use packaging design in their brand-Building process. Therefore the aim of our thesis is to provide practitioners and academicians alike with a better understanding of how packaging design can be used to create strong brands in the FMCG sector in the Scandinavian market. To reach the stated aim first we provided a solid theoretical background of packaging, its elements and its role in the marketing mix.

The construction process which is used today while constructing residential buildings has for along time remained unchanged. Unfortunately the development process has gone away frombecoming industrialized and instead most of the work is done at the construction site. In thisrespect this is a worse alternative because the project outcome will be more expensive and theconstruction time will be longer. Skanska?s vision is to have a process which is more like the oneused in small residential buildings which is fully industrialized.The constructing process for residential building involves more parties and therefore it becomesmore complicated.

For nearly twenty years people have been talking about Product models, but given that the building industry is so conservative, it is hard to implement new working methods. Product models are these days known as Building Information Modeling, BIM. People often say they work with BIM but they often forget the most important part, the information. A 3D model should be linked with characteristics and information. Information that can be invaluable for the facility manager.We have a vision that in the best of worlds the facility manager would be able to "walk" into the model and see what kind of installations are inside the wall or in the roof.

During the 1990?s a large number of building projects were revealed where lack of moistsafety precautions during the construction process had led to extensive moisture damage. Alsoresent implemented studies have shown that the problems with moisture damages have ratherincreased than decreased during the past few years. Moist is considered to be one of the mainfactors to cause unhealth due to deficiencies in the indoor-environment and does also causeunnecessary expenses and a reduction of the confidence in the construction industry.In this Bachelor of Science thesis three projects have been reviewed to examine how moistsafetyhas been observed during the construction process. Main focus has been to identify thebuilding components that are the most exposed to moist, and to examine how they have beentaken into account during the period of design and construction.

This thesis examines the tendering process from the point of view of Swedish building contractors. The purpose with the study is to chart the decision process for the contractors during the tendering process. The study is designed as a survey study. This made it possible to reach a wide base of respondents, not letting such factors as geography being an issue. The survey itself was characterised by a very high response rate compared to other similar studies. The result from this study shows that former experience from similar projects, current workload and the clients economic condition are very important factors for both whether or not the contractor will bid for a project as well as the cost estimation and tendering price. Former experience from similar projects is also an important factor for the determination of the indirect costs.