The purpose of this degree project was to build laboratory equipment for a new course in power electronics that starts this autumn 2010 at Uppsala University. The equipment is intended for student labs and it covers the most important areas of the course including rectifying, buck-/boost-converters and PWM-modulation. It is built as one sealed unit where all the electronics are built-in but visible and it has a connection board where students safely can connect the different circuits. The project has advanced from theoretical studies of circuit design, choosing of components and simulations to drawing the printed circuit board (PCB), soldering, case building, final testing and troubleshooting - basically most steps from an early idea to a final product. Measurements on the final product gave about the same results as the earlier simulations of the circuits and the result is overall satisfying..

Today many different types of lock systems are used all over the world. Passwords, finger prints and magnetic strips are a few examples. When the key is a three dimensional object, lika a physical metal key, the security depends, in a high degree, on that you can?t copy the object without access to it. One approach to copying the object is photographing the object, and from these photographs create a copy.

At Volvo Cars Torslanda's paint shop there is a requirement to in a fast and effective way get an overview of the plants capacity. Therefore a capacity template was constructed as a tool for the engineers at Volvo several years ago. This template has during the years become complicated and outdated. Thus this thesis work will resort as a new capacity template, built from scratch. The new template has been built up based on requirements from Volvo and the concept of OEE (Overall Equipment Effectiveness).

The Intensive Care Unit (ICU) is a special unit for patients who is in the need for emergency life-sustaining measures and every patient has complex medical- technical equipment. The experiences of a critical illness and the needs of critical care are experienced in different ways. The purpose of this study was to describe the experiences from patients in the ICU and how this experience has an influence on the patients. The method was a study of literature with a qualitative inception based on eight scientific articles and the analysis of content has been inspired by Graneheim and Lundman (2003). The result of the study is presented by four categories: to loose the ability to make themselves understood, to be forced to adjust to the environment of caring, to have the lack of connection with reality and to be in an intensive care environment, The results showed that patients in the ICU are affected by the attitude from the staff, the equipment around them as well as the sounds and lights in the environment there.

Vid Volvo construction equipment AB, Component division i Eskilstuna, har nedväxling i förpackningsstorlekar genomförts som en del i en omfattande omställning mot Volvo Production System och Lean. Genom att producera med mindre satsstorlekar och hemtagningskvantiteter, vill Component division sänka sin kapitalbindning och bli flexiblare mot variationer i produktionen. Dessvärre påverkar nedväxlingen förpackningskostnaden till följd av ytterligare hantering, transport och administration. För Component division är det viktigt att få en god uppfattning om hur alla förpackningskostnader utvecklas med tiden. De vill i framtiden följa ett lämpligt nyckeltal för att se hur effektiva de är inom förpackningslogistik samt hur beslut och förändringar påverkar kostnaden.

The aim of thesis was to, through a action research study and through individual interviews with five students, clarify their perspective on educational assistance in high school. The study shows that students prefer teaching in small groups outside of regular whole class because it gives the them access to the factors they consider crucial for a functioning support-time whit a skilled and dedicated teatcher, in a calm and safe environment. Moreover, the students claim the importance of technical equipment especially in the Swedish subject, but also in other subjects. Today the educational assistance varies from an outside-the-class teaching situation to a whole-class situation with teacher support as well as technicaal equipment. When the student were asked to describe the cinditions under which studies can be conducted with the whole class they tried to imitate the learning environment they have in a small group.

Holmen Skog is currently using a GPS-program called TraktInfo, originally developed within the company. They are now planning to switch to a new GPSprogram or allowing the contractors to buy other programs available from the logging equipment manufacturers. To be able to offer this flexibility, Holmen Skog needs to obtain information about the features offered by the different manufacturers in their specific programs, and also when the manufacturers are planning to start selling programs adapted to the new standard called StanFord2010. According to the study, the manufacturers are hesitant to StanFord2010 and there has also been a lack of clear signals from the customers and clients about what kind of different new features to include in the programs. The feature most frequently used by forest machine operators today is the option to keep record of the harvester?s path by creating a ?log plot?. This feature was not used to its full potential however, since only one out of eight of the forwarders included in the study had computers that were compatible with the harvester?s computer.

In this report the balconies? abutments for a property in Bo01-area in Malmö has been studied. The property which is called Vitruvius contains four build-ings where two of them have corbelling balconies with intermittent abutments. With intermittent abutment means that the 50 mm thermal bridge insulation that the balconies is equipped with, is broken regularly by a 300 mm concrete heel. The reinforcement bar that holds the balcony runs through this heel.

ABB is one of the world?s leading engineering companies in power and automation technologiesand their solutions improve performance while lowering environmental impacts for energycompanies and industries. ABB FACTS designs equipment and plants for series and phasecompensation.This thesis has been performed at ABB FACTS on the Mechanical Design (DM) department inVästerås, Sweden. The purpose of the thesis was to develop and design calculations andsimulation tools for ABB FACTS?s standard series capacitor platforms.

This work covers a broad analysis of the risks that could impact the achievement of electrical safety of electrical installations. The work includes both electrical equipment such as the installation of electrical equipment.The report illustrates the main technical characteristics of electrical connections greater than 10 mm2 and provides an introduction to the crimping systems for copper and aluminum conductors. In addition to that analyzes the factors that are important to assure the quality of an electrical connection throughout the value stream in terms of both materials such informations. Furthermore analyzed deeper the need for skills development of technicians and other staff.The different parts of this work are analyzed and presented, in theory to studies carried out both at Elpress AB and partly with the help of other scientific reports dealing with similar subjects. In addition, presents a survey that will help understanding the current perception of the electrical connections and cable crimping systems among end users.

This master thesis is an in-depth study of an existing heating system at a household cooperative in Uppsala that has been converted from district heating to a bedrock heat pump system. The study focuses on an economical system optimisation of the building?s complete heating system. The aim was to determine how well a heat pump system in large buildings actually work, find out possible ways to optimize the existing system and point out important system parameters for new heat pump installations in larger buildings.The project points out a possible energy cost reduction of 45 % without investment and further cost reductions with equipment investments. A reduction by 30 % is possible by improvements in the regulation system and 15 % is possible by maintaining the brine system.

To get the maximal output of your exercise in gym machines, there are different factorsto be considered. For example the strength of the muscle varies dependent on the positionof the muscles. To get the best results of the exercise the load has to reduce and increaseat specific positions.This study was made in cooperation with Caretaker Scandinavia AB, a company forsales, marketing and development in health care. They are general agent for Nordic Gymwho works with manufacturing of equipment and machines for gym and fitness.The aim of this study was to generate a method of measurement to evaluate and controlthe biomechanics of Nordic Gym´s workout equipment. A protocol for an ergonomicanalysis on the equipment has also been elaborated.One of the methods to measure the biomechanics was to measure the torque through thewhole movement.

This Thesis in Military Technology deals with experiences drawn from the forced introduction of Weapons Station 01, 2009. The work aims to identify the experiences regarding the forced procurement of military equipment to see how they can develop normal and fast procurement of equipment. The main conclusions of  this work, is to achieve greater capability and increase the military utility, are: -          Common objectives and priorities of stakeholders-          Response and joint types shall determine requirements for system-          Ensure an integrated project team also at lower levels-          Engage the integrated logistic support early in the materiel process-          Include Armed Forces staff as early as possible in the testing and validation-          Prioritize work to facilitate the rapid development of decision on use (BOA)-          Provide back up for increased redundancy in the mission area .

Historically transformers with system earth equipment have been modeled as open circuits in zero sequence. This approximation has been satisfying, but lately it has been discovered that equipment on one side of the transformer have responded to faults that occurred at the other side. Most of these problems took place when the majority of the system on the secondary side of the transformer contained cables. These findings have led to questioning whether or not the former model of the transformer in zero sequence is correct. This report investigates if it is necessary to represent the transformer in zero sequence in another way than it is usually done today.

Animals can be ill and need veterinary care for many reasons. The conditions can be more or less emergent, some can even be life-threatening. When an animal is in a life-threatening condition you can save the animals life just by having the right equipment near-by and ready to be used. This literature-study help you, as an active working veterinary nurse, with which these conditions are that can show up in your emergency ward and what you should have near-by to give animals with acute life-threatening conditions the care they need. The author also looked at work tasks at the emergency ward and found out that in Sweden it is not defined who can and/or should execute them. Interviews were also done with nine of the largest small-animal hospitals in Sweden to compare the studies found with the Swedish emergency wards.