The Master Thesis work this report is based upon has been conducted in cooperation with Svea Teknik AB. Svea Teknik is a consultant firm which is developing parts of a tunnel boring machine on behalf of Atlas Copco. The machine is being developed to mechanically excavate hard rock by fixating itself in the tunnel and then press a large rotating cutter-wheel equipped with disc-cutters against the tunnel wall. The disc-cutters are the tools that are in direct contact with the hard rock and are therefore exposed to extensive wear and needs to be replaced on a regular basis.The purpose of this Master Thesis has been to develop a service equipment that will enable time effective and safe changes of disc-cutters. The disc-cutters have a diameter of 17 inches and weigh about 130 kg.

Syntesdesign AB is an academic company that is supposed to enter the HIV drugmarket by manufacturing a "me-too"-drug with indinavir as the starting substance.Our task is to find 100 potential indinaviranalogues. Our further task is to suggesthow to perform a bondingassay to test the affinity for all these analogues. We willpresent a method, required equipment and calculated costs for the assay..

This study has been carried out in the spring of 2014 on behalf of PQR Consult AB in Stockholm. The aim of the study has been to analyse the energy usage of the building Skarpövägen 1 in order to explore the possibilites of saving energy by using appropriate equipment. These possible solutions have been simulated by using the programe IDA Indoor Climate and Energy, combined with a life cycle cost analysis. The laundry building, Skarövägen 23, has also been analysed due to its high amount of energy usage. The result of the energy analysis showed that the energy usage was much higher than the energy declaration.

The purpose of this work is to find out if the suctionvalve to the salivaejector for dental equipment in a simple way can be improved or if a new design is needed. The result of the examination of the suctionvalve shows that the friction between the piston and the seal is high and that this causes the valve in a few cases sheaves. The study concluded that only small changes in material or detail, improve the component..

Today the competition in the automobile industry is getting all tougher. The technology behind cars becomes more advanced. To get ahead of competitors car companies has to look into new areas of innovation.One important area is vehicle safety. Bigger companies have come so far in vehicle safety that difference between cars more depends on the car type (size) than the technology behind it.There is one area where vehicle safety that still has great opportunities for improvement, which is in active safety. The term active safety states that the car has the ability to identify treats and automatically respond to the treats.

    AbstractThe aim of the study was to describe factors of nurse?s experiences when they give NIV treatment to patients with acute respiratory failure in a lung department. Semi structured interview questions about how nurses experience to give NIV treatment on a ordinary lung department was done on 10 nurses, who work in a lung department were NIV treatment is given. Data were analyzed with content analysis. In the result there was shown two themes.

Hydroware Elevation Technology AB sells control and regulation equipment for hydraulic elevators. The company now wants to investigate the possibility of changing their present softstarters to frequency inverters to supply power to their pump engines. They also want to investigate the possibility of future use in so called ?intelligent? houses.The purpose of this report is to investigate these possibilities..

This thesis analyses how a radiology department at the largest hospital in Sweden, Karolinska University Hospital, most profitably could expand its capacity for investigating cancer patients using magnetic resonance imaging (MRI). The queues today for patients waiting to be scanned are long, which delays the start of cancer treatments. Meanwhile the hospital has a budget deficit of half a billion SEK, which make any expansion hard. In this thesis we evaluate the alternatives of investing in new machinery; utilize the current machinery better by using them more days annually or through a shift work system. Finally we evaluate a combination of these.

Husums plant has a selection of different pulp pumps at bleaching plant 4 and 5. The displacement- (HC-pump, Sund Defibrator PTD-60) and centrifugalpumps (MC-pump, MCA 42-200, MCP 30/20) are of interest in this report. The centrifugal pumps are controlled by throttle valves, which result in an energy loss. Chemical mixers are used to mix ClO2 into the pulp before proceeding into a holding tower where the bleaching process occurs.The energy demand of the different positions has been measured or calculated to be used in comparisons against new equipment. Quotations were requested and delivered from Valmet and Sulzer.

Husqvarna is a world leading producer of chainsaws with a well-established brand name. Husqvarna now has an interest in investigating the possibiltiy to expand their production of chains and guide bars to include cutting equipment for timber-harvesters.This project is a technical study which aims to answer questions about cutting equipment for timber-harvesters that have been decided in cooperation with Husqvarna. The questions have mainly been focused on forces, cutting speeds, service and maintenance -as well as general questions regarding the size of the Swedish market.Two methods have been applied to answer the questions. Interviews with retailers of harvesters, producers of harvester heads and harvester drivers.The main findings in this project show that there is a relatively small selection of harvester chains on the Swedish market. In contrast to the selection of harvester chains the selection of guide bars is quite large.

This degree thesis is based on an assignment from BEOMAT in Storfors. BEOMAT is a company that constructs and sellsclay pigeons to both the national and international market.Our main purpose with this paper is to find a solution/system that can replace the expensive and space demandingOlympic trap facility. Our solution will replace fifteen clay pigeon throwers with one automatic thrower whosimulate all throwers together. The system will be provided with an appropriate control system for mass productiontherefore this system needs to be user-friendly so no previous knowledge is required.Totally 405 different throw coordinates will be stored in the programme in nine different subprograms. According tothe Olympic-rules the throwers should coincidence within certain specified conditions, this will be solved with anrandomizer in the programme.

As a result of global competition, companies within the automotive industry are required to improve their production systems to achieve sustainable and competitive production. To attain operational excellence, companies have adopted concepts like lean and World Class Manufacturing (WCM).In order to deliver, companies need to increase the availability and reliability of production equipment. This demands focus on both operational and strategic maintenance, and efficient equipment acquisition and management. The main objective of this thesis is to identify processes and success factors that are necessary for improved maintenance performance. By conducting a case study and by performing a literature review, the following has been studied: 1) how companies within the automotive industry work with maintenance and maintenance strategies, 2) implementation of maintenance strategies, and 3) new acquisition and spare parts management for maintenance. The results show that basic maintenance concepts and related terms are well defined in the literature.

This study is an attempt to shed light on the importance of fiction as a bridge between different cultures and traditions. The objective of this essay is threefold. First it explores the potentiality of fiction as a communication channel between different cultures, societies and social groups. Secondly, it studies the availability of foreign fiction in Swedish language. And thirdly it tries to approach and analyze the structures and mechanisms behind that availability.

Compressed air is an energy source that is widely used in today's trucks and buses.Compressor located next to the engine supplies the pneumatic system with the compressed air and is lubricated with the engine oil. Some of the oil follows the air flow in both liquid and solid phase. The solid phase, namely the carbon particles are created due to the high temperature in the compression chamber.Oil- and particles carryover softens and destroys the rubber material in the air valves and disturbs the mechanical function of various components in the pneumatic system. In order to reduce oil- and particles carryover is an Air Processing System (APS) set downstream the compressor.No method for establishment of oil- and particles carryover from the compressor exists at the moment. Therefore the filtration efficiency of APS is currently unknown.

Arbetsplatsernas ständiga utveckling och förändring har lett fram till ökade psykosociala krav från de anställda som företaget måste bemöta. Ska man bedriva ett hälsofrämjande arbete bör hänsyn tas till hur kulturen ser ut på arbetsplatsen. Samlade värderingar och verklighetsuppfattningar kring hälsa skapas när individer samverkar med varandra och omvärlden, detta kallar vi ?hälsokultur?. Syftet med studien är att beskriva hur hälsokulturen ser ut på ett företag och vilka möjligheter och resurser som finns på företaget för att utveckla denna.