This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

The Main problem: How small-sized manufacturing companies can create and sustain a stable position in the industry, which leads to profitability.Purpose: The purpose with this essay is to compare two small-sized manufacturing companies, Datek Industrielektronik AB and AB Micatrone to study which strategical resources each company possesses. At the same time analyse if the strategical resources are to be consider as sustainable competitive advantage.Method: A case study has been implemented in two small-sized manufacturing companies. The collected primary data derives from semi-structured interviews.Theoretical framework: The theoretical framework is based on The Resource-based view where the independent variables are the VRIO-model, resource tree and external resources. The dependable variable is sustainable competitive advantage.Empirical foundation: The empirical foundation is based on the compilation of the few conducted interviews with Datek and Micatrone.Results & Conclusion: Datek and Micatrone show both similarities and differences in what creates their sustainable competitive advantage. The management of both companies creates according to the VRIO-model sustainable competitive advantage.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

Given that the end-customer has become more demanding, the retailer has to deliver products according to the market demands, which have forced manufacturing companies to constantly search for new opportunities to reduce costs and improve efficiency. It is, therefore important to choose suppliers that are able to compete with the market demands.The market demands in the textile industry have lead to shorter product life cycles, which have caused manufacturers to deliver flexibility with high technology to compete successfully on the global market. To achieve the market requirements the underlying factor is to be aware and optimally use and control time. New technology can have a major influence in the production development, if the company choose to take benefit of the advantages, by optimal allocation of the internal resources the productivity and efficiency will increase, to accomplish a competitive advantage. One way to achieve this is by investing in a Unit Production System.In our thesis we have questioned what the main driving forces for an apparel manufacturing company is when it chooses to invest in new technology.

This thesis serves to examine how manufacturing SMEs consider outsourcing. Furthermore, we aim to identify the main characteristics and patterns for these types of companies that can explain their rationale in such a decision. The chosen method for this thesis is abduction and selected research approach is multiple case studies. Seven case studies have been conducted at EAB AB, Esbe AB, Hörle Automatic AB, Pelly Industri AB, SGV Industrier AB, Swede-Wheel AB and Wulkan AB. Our findings have illustrated that although traditional outsourcing theory provides a good platform for explaining the rationale behind outsourcing decisions in SMEs, we have identified additional considerations that SMEs, operating as 2, 3 or 4-tier suppliers towards OEM-corporations, make.

 The purpose with this thesis was to develop a designguideline which will simplify the development of new products that will be laser welded. The need for this thesis has come forward from the quality problems that Volvo Construction Equipment, Components Division is having with their laser welding manufacturing unit. The reason for the problems emerges from the bad communication between the development unit and the manufacturing unit within the company when the products produced today was developed. This resulted in products that were hard to and in some cases almost impossible to weld. To avoid these problems from occurring again it was needed to gather the experiences within this area and compile it and present in a brief a pedagogical manner. The information for the groundwork of our results has been gathered by interviews of several key persons in Volvo Construction Equipment, Components Division.

This examination work is performed at the institution of industrial economy and production at Jonkoping technical university, for JELD-WEN Door Solutions plant in Forserum.Today the focus in the company is on to reduce their inventories binding of capitals as well as inventory of products and that includes to get a good control of the supply and handling of material which is of great importance.JELD-WEN Door Solutions is one of the worlds leading producers of windows and doors and the head-office is located in Oregon, USA.A great number of wooden doors are manufactured by the company in varying of constructions, classifications and performance.The production of the plant in Forserum has a project- and customer focus manufacturing where only internal doors are produced. The overall market they are concentrated on is to different institution such as schools, hospitals etc.The purpose of this work is to investigate possibilities to improvement of material- and production control at JELD-WEN. The report will handle the master production schedule to and from the production divisions within manufacturing industry. Focus will be on the way for information- and material flows from arrival, transport within the company and further on to customers.Further a map of the flow was performed which gave a clearer picture of the connection between the flow of information- and material for the manufacturing process. On the basis of the mapping of the flow, the group discovered that the flow of material had some improvement potential.

This Bachelor of Science thesis was carried out at Metso Panelboard AB, located in Sundsvall, Sweden. The work lasted for 10 weeks and began at the end of February 2007. Metso Panelboard is one of the leading suppliers of complete lines, single machines, engineering knowledge and after-market services to the fibreboard industries. The task involved building a 3D-model of a dryer cyclone in the CAD-program Pro/ENGINEER. A dryer cyclone is the part where the tree fibres are dried in the process of manufacturing fibreboards. Currently, it takes about two weeks to draw a dryer cyclone. By creating a 3D-model of it, which should have the functionality to be generated to different sizes, the goal is to decrease the drawing time to about 20 hours and to increase the quality of the work. This report includes the fundamental theories behind the manufacturing of fibreboards with focus on the dryer cyclone.

This thesis describes the design of a tipping trailer, from a company?s demands andrequests to complete manufacturing documentation. The design is developed for thecompany Abexor AB in Östersund that produces tipping trailers. The product issupposed to be used by Abexors customer to transport cargos of different kinds,such as gravel, stone, dirt, etc.The work commenced with a meeting at the company where demands were set.After that a pre-study was conducted to find out what traffic rules were required forthe trailer to be allowed to be driven on roads. Similar products were examined tosee how the trailer could be designed.

The aim of my thesis was to do a Life Cycle Assessment (LCA) of an average thread tap that is manufactured by Dormer Tools AB, and to create a practical model that the company can use in order to study other thread taps from an environmental perspective.The method of LCA is used to investigate the environmental effects of a product during its life cycle. This is a gate-to-grave analysis with focus on steel and thread tap manufacturing, coating procedure, use, waste management and transports. Three common coating types were compared separately. Steel manufacturing answers for the highest energy and raw material consumption under the life cycle of the thread tap. Its emissions contribute to global warming, acidification and eutrophication above others.