Detta examensarbete har utförts på uppdrag av Koenigsegg Automotive AB, som utvecklar, tillverkar och säljer högpresterande sportbilar. Företaget erbjuder fälgar tillverkade helt i kolfiberkomposit, som ger betydande viktbesparingar i jämförelse med traditionella metallfälgar.Efter tillverkningen kräver fälgarna viss bearbetning vid anläggningsytan mellan fälg och däck. Syftet med examensarbetet har varit att undersöka möjligheten att utföra bearbetningen av fälgarna in-house i Ängelholm, och målet har varit att konstruera en maskin för detta ändamål.Projektet inleddes med en litteratursökning, där svårigheter och möjligheter gällande bearbetning av kolfiberkompositer undersöktes. Till följd av de undersökningar som gjordes, valdes bearbetningsmetoden svarvfräsning och ett antal konstuktionskoncept genererades. Genom ett antal utvärderingar utvecklades ett speciellt koncept vidare till ett komplett produktförslag.Produktförslaget är komplett med analyser, beräkningar samt tillverkningsunderlag, som ger uppdragsgivaren bättre insikt i sina möjligheter.

The work that is the basis of this Master Thesis was performed on Scania´s group of cabdevelopment, and concerns the GPS-system in Scania´s trucks. Today, the GPS-systemconsists of an active antenna mounted on the roof of the truck. The antenna is connectedto the receiver with a coaxial cable.The purpose with this Master Thesis was to develop and evaluate a new GPS-system,where the information is distributed using a LIN-network. Today, each unit requiringGPS-information is equipped with its own antenna and receiver. This solution has beenthe most cost effective to this point.

In this report you can get a complete instruction about how to build your own development system for the PIC-processor. This card will be used for laborations for the students at LITH-ITN. With this card you can send new assembler codes (new instructions) down to the microprocessor via the Serialport on your computer. Then the new instructions for the microprocessor will start to execute. We made a solder paste stencil at Campus Norrköping solder paste stencil laboratory.

This study investigated the possibility of implementing three standards, Transistion Minimized Differential Signaling (TMDS) and two versions of Stub Series Terminated Logic (SSTL), for inter-chip communication in a specific manufacturing process. The two SSTL standards were implemented in one transceiver system while TMDS was implemented in a separate system. The evaluation was done with Spice simulations on schematic level with some parasitic capacitance and resistance. The idea was to investigate the possibility of implementing these standards and get an idea of eventual shortcomings. In order to create models as a basis for evaluation, simulation environments with models for circuit board and packages were created and transmitters and receivers were designed.

Det fenomen som varit föremål för den här studien är psykosocial arbetsmiljö. Fenomenet har undersökts med inriktning på tillverkningsindustrin och organisationsformen Lean production. Studien syftar till att erhålla en djupare förståelse av hur medarbetarna i den här specifika kontexten upplever den psykosociala arbetsmiljön. De frågeställningar som studien ämnar besvara är:-Vad innebär en god psykosocial arbetsmiljö för medarbetarna i organisationen? -Hur upplever medarbetarna den psykosociala arbetsmiljön i organisationen? Studien genomfördes med ett induktivt förhållningssätt.

The development of productivity in the construction industry has long been at a steady state compared to the manufacturing industry. Studies have shown that, amongst other things, waste on construction sites can reach up to one third of the total production cost. This has been observed from different aspects, and change is forthcoming.This thesis aims to provide a foundation for an increased productivity at production sites of building bridges. It is primarily based on a field study at Skanska, at a bridge construction site near Grängesberg. Via continuous interviews with the whole production crew, construction workers and management, information on interference and possibilities of improvement at the work site has been documented.

Alfa Laval?s strategy is to focus on modularized product platforms. Several benefits areforeseen, reduced lead-time, less costs, shorter Time To Market and better quality.Development and verifying will be carried out on block level. Today the separators arebeing tested as a complete unit. A number of factors affect the test results and problemsthat are encountered can be hard to identify.

Electrolux Laundry Systems is the world leader in manufacturing professional laundry equipment.The machines are used in the hotel sector, elderly care, in multifamily houses, laundry bars, and incommercial and institutional laundries.If there is oil or grease left in the clothes after washing may the heat from the dryer cause a chemicalreaction. This reaction may, under certain circumstances cause a fire inside the drum. Competitors toElectrolux has developed its own systems that extinguishes fire inside a tumble dryer and customershave expressed desire to purchase a fire-extinguishing system. Therefore, the project team receivedthe task by Electrolux to develop a fire-extinguishing system that extinguishes a fire in a tumbledryer.The purpose of the project has been to develop a system that both detects and responds to fire in anindustrial tumble dryer to meet the competitors and to satisfy customers' requirements.The goal was to develop a fire-extinguishing system for Electrolux Laundry Systems and develop afully functioning prototype.The project began with information searches on a variety of methods to both detect and extinguish afire. Subsequently, a number of different methods were used to develop a final solution and make aprototype.The result of the project is a fire-extinguishing system that extinguishes a fire inside a dryer.

This thesis describes the redesign ofequipment designed for drying bags thatis used in Fresenius Kabis´manufacturing of their nutritionmedicine in Uppsala. The need of thistask arise during the start of thedevelopment of a new packaging line werethis equipment were meant to be used. Anevaluation of the bagdryers capacity andcapability was necessary.The work started with gathering ofinformation from suppliers of the usedcomponents and from the responsibleengineers for this equipment. Aneducation to learn how the equipmentworked and how to operate it were taken.That was followed by the creation of astudy plan were the tests were plannedto test different parameters effect onthe drying result and to see if thebagdryer managed to handle the bags ofthe correct format in the pace that theequipment should be designed for.The test results detected a need ofdesigning a unit with a function thatholds the bags in place while passingthrough the dryer in order to attainhigh quality results. The results werelater used for optimization of thedesign.

The purpose of this work is to design and construct a device able to measure the mechanical attrition of oxygen carrier particles. Those particles are used in chemical looping combustion and in the present situation there is a lack of knowledge in how the attrition process work and in which extension. To find already tested solutions trying to answering this problem a literature study wascarried out and the best solution found was the so called Grace-Davison Jet-Cup method. This method is supposed to emulate the attrition caused by a cyclone separator and its advantages are that it is possible to use small test amounts, 5-10 g, and a thirty minutes long test will be enough to acquire useable results. An device was designed based on the Jet-Cup method with some slight modifications.

AbstractThis qualitative study has been made to examine which factors that are required to create a work place that can be associated with loyal co-workers. The study covers half structured interviews with nine people on different levels and with different positions, within a manufacturing company in Värmland. Our ambition with this study is to find out if, and if so, in what way the view on loyalty and which factors that are required to encourage loyalty, differ depending on witch level one belongs to in the organization. Our thesis is that our respondents will have various ways of expressing the term loyalty, and that these various ways are linked to the different levels that each employee is currently stationed at.The result of this study shows that the way people look at loyalty, and what loyalty is really about, does not differ that much among our respondents, regardless of their level. The factors that, according to the respondents, are important if one wants to create a work place that can be associated with loyal co-workers are: to be able to feel trust towards and have faith in those one works with, as well as the company and the way things are being run, to be able to experience the feeling of community, and that one is happy with ones work place, as well as ones co-workers.

This report deals with prefabricated bathrooms and the advantage, during the production process, they have compared to ordinary produced bathrooms.The work is done together with the building company JM. The common task is to investigate if the manufactures, in spite of standardized design can meet the concept of JM, i.e. high flexibility and adjustment towards the customer. In JM they are doubtful to the method, as they did not yet worked with prefabricated modules and think that the choises for the costumer will be limited.There will be a short resume of the progress of the bathrooms and its importance as sanitary and wellbeing.The recent problems with damage caused by damp in bathrooms. Have resultade in regulations.

The thesis was performed at the lighting company Zpecta AB. Zpecta needed to develop alternative attachment of their LED-luminaire Capella. Today Capella attaches in metal ceilings with four magnets. Zpecta got indications from their customers that there was a need for other attachments. The purpose is to determine the customer?s requirements and the interfaces that are considered for Capella.During the thesis, Capella was only on the market for testing and evaluation.The thesis was initiated to create a specification.

This report was written as a result of a Bachelor Degree Project at the School of Technology and Society at University of Skövde spring 2007, together with Jede AB in Mariestad. The report covers the development of a door to a coffee vending machine that is under construction, and will in a chronological order describe the project from ideas to final product.The project started with a rather extensive feasibility study that thru market research and user tests sorted out the opinions of potential customers, concerning today?s available assortment. Technical areas concerning materials and manufacturing methods were also scrutinized for the consideration of the possibilities of a future production.The next step was to constructively generate ideas and thoughts that later on could grow to be potential solutions. After several weeks of hard work and pieces of good advice and recommendations from the assigner, four comprehensive concepts were built up.

Milk fever, or parturient paresis, is the second most common disease in Swedish dairy cows. The disorder is associated with the onset of lactation when some cows are unable to meet the metabolic demands of calcium to support milk production and therefore develop a state of hypocalcaemia. Clinical hypocalcaemia (milk fever) may lead to coma and death in severe cases but subclinical hypocalcaemia has also been shown to have negative effects on e.g. feed intake and production and to increase the susceptibility of the cow to develop secondary diseases. The nutritional strategy applied precalving is of great importance in preventing milk fever and e.g.