The vision of this thesis was to create a concept that can be used as a base for amachine construction. The purpose of this project was to use different methods todevelop a concept that on the best way meets the sat up requirements. This projecthas been divided into three stages/parts; principle, primary and the final solutionstage.This thesis has been conducted in collaboration with Västkustägg AB. It is aconstruction project designed to construct a machine that will automatically putlabels on the egg packages. Västkust AB wanted to automate this process.

The most predominant method for forest harvesting in Sweden is the cut-to-length method based on two-machines, a harvester that fells trees and cut them in a predefined length, and a forwarder which transports logs to a landing area for further transport to a processing facility. New machine solutions have to be much gentler to the ground than today?s machines. To be able to develop a forestry machine that preserves the terrain requires a proper understanding of the interaction between tire and soil.The goal of the project is to contribute to the existing knowledge of forest machine tire-soil interaction and to develop a tire-soil model that enables dynamic simulations of forest machines operating in rough terrain. The modeling has especially been focused on the interaction between tires and soft ground.A comparison of theoretical data of different WES-based terrain interaction models and a comparison test data from a full scale field test is presented.

Åmotfors Bruk AB (ÅBAB) has today an inefficient production of steam for the manufacturing of paper. Unpredictable energy prices and modernisation of the current equipment has been the underlying factors to invest in a thermal power plant, mainly driven by garbage. This facility will not only use the steam for paper production, it will also generate electricity through a steam turbine. Today, when a fault on the supplying line occurs which leads to disconnection of the external grid, all the support of electricity to Åmotfors Bruk (ÅB) will disappear. This will lead to major interruptions in the paper production, which will cause severe economical losses.

Hemp is an old agricultural plant and has been used for hundreds of years for making textiles, ropes and other fibre products. In the middle of the last century the Swedish government prohibited all growing of hemp. Natural fibres were replaced by syntetic fibres instead. Today there is a newly awakened interest for using natural fibres from renewable materials. Growing of industrial hemp for fiber is allowed in Sweden again. I want in my Paper give Swedish growers an insight of which harvesting methods that have been tried in Sweden and how they worked.

Forest streams and the associated riparian zones are sensitive to disturbances and changes that occur within these riparian areas. Particularly sensitive are small streams of low order, which will have large impacts down-stream. The disturbances that occur in the riparian zones are reflected quickly in the stream. Driving with forestry machines in the riparian zone will have detrimental effects to the soil and water. Driving the machines will lead to changes in the mineral soil composition, resulting in the reduction of porosity, less infiltration, compaction, and an increased bulk density.

The scarcity of qualified forest machine operators as well as the increased competition for competent machine operators among others from the mining industry in Norrland, were the reasons to investigate what attracts and what deters active and potential forest machine operators to the occupation. An interview study was conducted among four groups with four persons in each group. The groups were students in year 1 and 3 respectively at a forestry school at upper secondary school level as well as employees of a forest company and employees of contractors. The majority of all respondents were of the opinion that their interests in machines had been important for the choice of occupation. But for the active machine operators both the interest in the forest and their interest for machines have had importance for choosing this occupation.

This study includes a life cycle assessment, LCA, on an ecological produced cotton shirt for the company Reflective Circle, which designs ethical and ecological clothes.Initially were cotton farming and textile production studied to gather basic knowledge about the processes. Since this shirt is being ecological produced in the whole production chain, we studied what an ecological production means, but also how a conventional production works. When this was done we could start to discuss the differences and similarities between the production of the shirt and general conventional production.When the LCA was first initiated, the main focus was on the green house gas emissions from the manure at the cultivation. Thereafter the process steps such as picking, ginning, carding, spinning, weaving and sewing were being studied. The picking is done by hand, but the rest of the processes are handed by machines which consumes energy.

Ever since ABB has begun diecasting their rotors instead of permanent mold casting it,variation in the quality of the cast has arisen. Diecasting is performed in three differentmachines, M1, M2, M3 with 400, 660 respectively 800 tons of die locking pressures.The aim of this thesis is to answer the following questions:What is the ?right? cast quality? How is the right quality achieved?For sizes 160-180 solutions will be proposed that consider eccentricity between thelaminate and the short circuit ring as well as elimination of the thin Al film that appearson the outer periphery of the rotors.Through considering the statistic material the most often diverging rotor type has beenidentified and one of the actual rotors has been sent to a laboratory to be analyzed inorder to establish the current defects. The result of the analysis shows that there areplenty of gas- and oxide-porosity.It has been proved that every time the dies temperature decreased below 120°C thecontent of gas porosity increased. It is due to rapid solidification of metal that flowsthrough the ?cold? laminate.It has confirmed that enhanced porosity in squirrel cage causes high impedance in therotors.

At Volvo Construction Equipment outside Eskilstuna a wide range of heavy equipment machines are developed that are used by a variety of industries worldwide. For the handling and maintenance of these machines a deep knowledge is often required. Volvo CE and their dealer Swecon offer courses for both drivers and technicians that last for 1-2 weeks. Out on the workplaces however, the knowledge from these courses need to be supplemented with information from the machine?s operator and repair manuals.

Metso Paper offers a front-running range of solutions and services for the pulp and paper industry. At the baling unit, design solutions are developed for manufacturing and handling of pulp bales. The machines are continuously developed to satisfy customer needs. One big step in the development of the baling line was to remove hydraulics from the machines and replace it with electrical motors and pneumatics. This was not done on the folding machine which is still driven by mainly hydraulics.

ProblemThe manufacturing industry is a mature industry where the profit margins are small and the competition is hard. This makes it hard for both manufacturers and resellers to gain market shares and reach reasonable profit margins only by selling products. Therefore Swecon who is reseller for Volvo Construction Equipment tries to find alternative methods and ways to increase their profit. An alternative source of income could be to develop the range of services that are connected to the ground products.PurposeThe purpose of the thesis is to examine how Swecon in southern Sweden can improve their offers of existing services connected to the ground product and investigate the demand of new such services.MethodThis study is based on a qualitative study of five of Swecons local offices and five of Swecons customers. The empirical framework is mostly based on personal interviews but in some cases information was retrieved by using phone interviews.

The agriculture is today in a development that leads to bigger and bigger units in the primary production. To be able to follow this development many companies chooses to cooperate in different ways. The most radical change is when farmers fuses with other farmers and merge into to a big collectively owned operation firm. The reason behind this idea is that the firms achieve the big companies advantages by being complement to each other. The purpose of this essay is to make an economic analysis of two crop production companies who works together in an operation firm.

The semantic web is a vision of the Internets future, there machines and humans can understand the same information. To make this possible, documents have to be provided with metadata in a general language. W3C has created Web Ontology Language (owl) for this purpose.This report present the creation of a LaTeX package, which makes it possible to include metadata in pdf files. It also presents how you can create annotations, which are bound to the metadata that's been generated. With the help of this package it's easy to create pdf documents with automatically generated metadata and annotations..

Ditch cleaning is increasingly important in Swedish forestry. This study compare different concepts concerning machinery, namely two general-purpose excavators of different sizes, 8 tonnes and 15 tonnes, versus a dedicated machine constructed solely to deal with ditch-cleaning. The machines were tested on rough as well as on gentle terrain and on open terrain as well as in young stands in connection with thinning. The conclusions were that the excavators are more versatile and have greater capacity than the dedicated machine, while the latter excels in quality of work. Interestingly, there was no significant difference in performance between the both excavators..

This master thesis investigates quality procedures and measuring of solid carbide end mills, with the main focus on measuring equipment. The thesis has been written in collaboration with a special production department for solid carbide end mills at Sandvik Coromant in Gimo. The department?s needs and constraints have been the foundation of the project and the main research question is: how to measure end mills in order to ensure good quality of the produced end mills. The project has contained both a theoretical study consisting of a literature review and practical studies in the workshop with the objective to identify an end mill?s main parameters and the relationship between an end mill?s geometry and the manufacturing processes.