This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This report shows methods and workflow when exploring the potential to change Outotecs HCD Silver Electrolysis machine to a module type. It?s done as an attempt to lower the workshop and installation costs and to give customer a more accurate prize directly. To do this a concept was produced which was set to a stress test. Additional objectives were to investigate freight and installation procedures, pneumatic connections and to calculate the difference in cost.Once the concept, a reinforced type of the original frame, was chosen stress tests in computer simulations were made and appropriate alterations were made.

A one-cylinder research engine has been used for studies with a Diesel Dual Fuel concept (DDF). DDF is a concept that utilizes a pilot diesel injection to ignite a homogenous natural gas/air mixture. Emissions and engine efficiency have been analyzed in an emission cycle called European Stationary Cycle (ESC) and the knock/pre-ignition problems with this type of engine have been investigated.At low and mid torque levels, an early diesel injection around 60 crank angles degrees (CAD) before top dead center (TDC) was used. At these loads raw NOxemissions was below EURO 6 level (0.2 g/kWh). NOxwas at EURO 5 level over the complete ESC without after treatment and with SCR at high loads it should be possible to reach EURO 6.One issue with DDF is the high HC emission levels.

This thesis revolves around NATO?s role in the Ukraine crisis with the startpoint in 2014. Specifically, through conducting a qualitative content analysis of various NATO related material, a study regarding NATO?s security strategy and defense strategy, and the strategies' implications and roles in the Ukraine crisis, was able to be conducted. The purpose was to obtain an understanding of how NATO?s strategy has been interpreted and implemented in relation to the crisis.

The purpose of this study is to gain knowledge and a broader understanding for how pre-school teachers describe the importance of planned play environments including in what manner children are given influence. By qualitative interviews with five pre-school teachers from four different units I was able to gather data that shows how the planning process concerning a specific play environment had worked and why it looked as it did. The results show among other things that the pre-school teachers viewed the play environment as a vital part of the daily operation and pointed out that it was of vital importance that it came from the children?s interests. Depending on how the play environment had been organized and what its purpose was it offered different amounts of affordances..

The project team has chosen to carry out the project itself. This is to be able to work more flexibly in the product development process and not be guided by some guidelines.Every day, we read in the media about a new truck burglary. The problem has become so common that we do not even notice it in the media. Each year the theft of 1 billion of Sweden and the entire 82 billion in Europe in 2008. This is an increase of 10 billion by 2007.

Abstract This Concept Analysis according to Walker & Avant (1995) studies the concept of uncertainty in the nursing context. It consists of four parts where uncertainty in general have been encircled in a semantic analysis (part one) and a qualitative content analysis consisting of an questionnaire, distributed to the staff members at one nursing and medicine institution, with an open question about the meaning of uncertainty (part two). The third part is a literature study of the nursing context to find out how uncertainty is described (part three). Part four is the actual concept analysis based on the three first parts. Uncertainty in the nursing context is an individual conscious experience witch is changeable and impressionable. It is chained together with its antecendents and consequences.

This essay describes how theatre can be a tool in social work. The essay evaluates the Swed-ish KRAFT-project, a course for unemployed people with the goal to make them grow as in-dividuals by using drama exercises and performing a theatre play in front of an audience. The essay is a quantitative secondary study of the questionnaire used in the KRAFT-project. Through analysing the questionnaire the participants answered this essay tries to explain the results from a social psychological perspective. The essay also discusses how the participants? self-concept and self-esteem could have been affected by the KRAFT-project.

Sustainability work is something that is emphasized more and more. Corporate Social Responsibility, CSR, is discussed and the question of how much responsibility companies should really take is frequently in the news. Companies tend to ask themselves how much responsibility they should take. CSR is a common concept of companies environmental and social work and a concept we tend to see here and there in our modern society. CSR includes companies? social responsibilities, both in terms of carbon footprint, working conditions, social responsibility and more.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

Trygghet är en subjektiv upplevelse som påverkas av många olika faktorer och påverkar människors hälsa och beteenden. En individs hälsa påverkas av hela den omgivande miljön och otrygghet kan leda till att områden inte utnyttjas, vilket kan föranleda inaktivitet, isolering och stress. Trygghet påverkas negativt av förekomst av brott och positivt av gemenskap, mötesplatser och delaktighet. I Sverige upplever de flesta sitt bostadsområde som tryggt men det är vanligare att boende i flerfamiljshus i större städer upplever otrygghet. I stadsdelen Råby i Västerås finns mycket flerfamiljshus och har ett rykte om att vara otryggt.

The present work is a continuation of the ideas developed in previous projects during my Masters studies that explored the relation between pattern, form and space. Starting from the pattern multiplication for space construction the present project proposes textiles as an assortment of flexible expressions. The purpose of the project is to explore aesthetic and functional potential of textiles for out door temporary structures. This is to create a pattern interface which filters sunlight through a textile surface to offer instant sheltering solutions for out door activities. The project combines research and analyses of outdoor temporary structures and scope of textile in the area.