This thesis describes the developmentof a device called "Oil Separator"which is used for washing vehicles andparticularly car washing. The devicedeveloped for Mr. Car Bilvård AB inUppsala, the company's work involvespassenger transport and courierservices. The company needs anexternal device that meets theenvironmental standards to wash theirown cars in the premises without theneed to modify or reconstruct on thepremises ground as the premises is ona leased contract.Work began with a preliminary study onthe literatures that describes boththe function and structure ofdesigning the device. A few interviewswith other car wash companies had beenimplemented, and some measurements.After collection of the necessaryinformation the specifications ofcustomer requirement was presented .With these requirements a fewconcepts was generated and weighedusing the Pugh matrix for conceptsselection for further development.The final concept was furtherdeveloped and a design has beenpresented.

Manure evaluation has been suggested as a cheap, fast and easy method which can give information about the digestibility of the ration, the function of the rumen, where in the gastrointestinal tract the feed is digested and the health of the cow. An experiment was conducted to study how manure evaluation could be used as a management tool in Swedish Dairy farming. Manure was collected from cows on Kungsängen Research Station and from 9 other farms. The manure samples were analysed for dry matter, ash, starch, pH-value and particle size (wet sieved). Also, the consistency of the manure was determined on a 5-point scale and the colour and smell were noticed. Penn State Forage Particle Separator was used for determining the particle size of the roughage.

Fieldstudys on 22 farms (23 silos) to study relationships between the actual particle size of the maize silage and the theoretical length of cut. The measure of theoretical length of cut were stated by the farmers and not measured by us. Particle size of maize silage was determined using the New Penn State Forage Particle Separator. SLU Skara made a special sieve for us, that had larger holes than de original sieves. The samples were shaken after instructions and then the material was weighted. We have also been taking out samples for microbiological analyses from the silos on 13 of the farms.

This has been a thesis work for an bachelor degree at Umeå university. The work has been done at LKAB?s facilities in Kiruna and its main purpose has been to investigate and construct some conceptual designs for replacing a screen with magnetic separation in KA3 concentrator plant. First all information available about magnetic separation was gathered and studies of magnetic separation at the sorting plant and studies of the plant KA3 was conducted. Companies that manufacture magnetic Separators were contacted.

The purpose of this work is to design and construct a device able to measure the mechanical attrition of oxygen carrier particles. Those particles are used in chemical looping combustion and in the present situation there is a lack of knowledge in how the attrition process work and in which extension. To find already tested solutions trying to answering this problem a literature study wascarried out and the best solution found was the so called Grace-Davison Jet-Cup method. This method is supposed to emulate the attrition caused by a cyclone Separator and its advantages are that it is possible to use small test amounts, 5-10 g, and a thirty minutes long test will be enough to acquire useable results. An device was designed based on the Jet-Cup method with some slight modifications.

The purpose of this work is to design and construct a device able to measure the mechanical attrition of oxygen carrier particles. Those particles are used in chemical looping combustion and in the present situation there is a lack of knowledge in how the attrition process work and in which extension. To find already tested solutions trying to answering this problem a literature study wascarried out and the best solution found was the so called Grace-Davison Jet-Cup method. This method is supposed to emulate the attrition caused by a cyclone Separator and its advantages are that it is possible to use small test amounts, 5-10 g, and a thirty minutes long test will be enough to acquire useable results. An device was designed based on the Jet-Cup method with some slight modifications.

This thesis is a product development project that was performed at Alfa Laval Tumba AB. In the past Alfa Laval have manufactured gas Separators for engines where gas flows were cleaned from oil. A new business area for this kind of technology has shown to be the manufacturing industry where oil mist has to be separated from the vented air. Therefore a new and bigger design is needed to be able to handle the greater gas flows. A product like that would be a strong competitor on the market when the maintenance would be low in comparison to today?s equipment.During the project several concept suggestions were developed using customer interviews and research as input.

Alfa Laval?s strategy is to focus on modularized product platforms. Several benefits areforeseen, reduced lead-time, less costs, shorter Time To Market and better quality.Development and verifying will be carried out on block level. Today the Separators arebeing tested as a complete unit. A number of factors affect the test results and problemsthat are encountered can be hard to identify.

The purpose of this work is to design and construct a device able to measure the mechanical attrition of oxygen carrier particles. Those particles are used in chemical looping combustion and in the present situation there is a lack of knowledge in how the attrition process work and in which extension. To find already tested solutions trying to answering this problem a literature study wascarried out and the best solution found was the so called Grace-Davison Jet-Cup method. This method is supposed to emulate the attrition caused by a cyclone Separator and its advantages are that it is possible to use small test amounts, 5-10 g, and a thirty minutes long test will be enough to acquire useable results. An device was designed based on the Jet-Cup method with some slight modifications.

There is a common belief that the arts contain knowledge of creativity that can enrich the business world. Similarly, the arts are in need of additional support from the private sector and know-how of business practices. In short, there is a need for mutual understanding. With my background as a dancer paired with my studies at the Stockholm School of Economics I have taken the challenge of bringing the two worlds closer together. By changing a social system, like an organization, it is possible to get a better understanding of it.

Bildtraditioner, ämnesintegrering och elevperspektiv är viktiga ingredienser i denna C-uppsats. Undersökningen tar sin plats på en gymnasieskola som arbetar ämnesintegrerat, KF Gymnasiet, där jag själv är bild- och medielärare. Jag har valt att följa eleverna i en projektgrupp genom deras arbetsprocesser i ett ämnesintegrerat filmprojekt. Genom intervjuer och enkäter har eleverna fått berätta om sina uppfattningar om bildämnet; ett material som sedan bearbetas genom diskursanalytisk metod. Jag har arbetat med eleverna med både teckning och måleri, för att sedan ämnesintegrera bild med svenska och engelska i ett filmprojekt.