Rapid Granulator is one of the world's largest producers of granulators, which is a kind of grinderwho grinds discarded plastics to granules which later can be reused when pressure molding plastics.The company wanted help in developing a new, or alternatively extending their previous,measurement equipment. The old equipment was hard to use, required changes in the code fordifferent measurement scenarios and had a limited array of measuring quantities. Rapid had an ideaof a similar concept only with a greater number of input ports, better range of applicable sensors andan advanced yet easy to use interface. The system is supposed to be placed at Rapid's test departmentwhere it will be used as a tool for finding faults and provide data which can be used for furtherdevelopment of the granulators.The project's members accepted the task and immediately began searching for suitable componentsfor the system. After the search was completed a list of costs, limitations, sensors, I/O's anddevelopment environment was presented to Rapid's staff.

This thesis is performed at Saab Bofors Dynamics in Karlskoga and investigates a technique for ranging with laser pulses. The investigated technique is called Constant Fraction Detection (CFD). Described briefly, the received laser pulse is split into two equal parts, where one part is delayed half the pulse width and inverted. This signal is added to the original pulse. The resulting curve has the shape of a laying S and the detection of the zero level is used to stop the time measurement.

To be able to measure high-surge voltages and transients with short rise times youneed measuring instruments with a high sampling frequency and large Bandwidth.These surges and transients occur primarily at lightning but can also occur at forexample at connecting errors at an electrical switch-gear. This report describes thework with finding two solutions for measuring and log data from these surges andtransients. One temporary solution where a measurement program has beendeveloped. A second solution where different company solutions have been analyzedto decide which fits best. For these measurement solutions two solutions for bringingdown the voltage has been used.

The power consumption has grown rapidlyin the last decade. Fossil fuels and theneed for alternative energy sources aregreat. Ocean waves are a renewable andsustainable source of energy that hasbeen relatively untapped. At UppsalaUniversity research and development havebeen done for several years. Severaltypes of wave energy converters (WEC)have been created.

To be able to measure high-surge voltages and transients with short rise times youneed measuring instruments with a high sampling frequency and large Bandwidth.These surges and transients occur primarily at lightning but can also occur at forexample at connecting errors at an electrical switch-gear. This report describes thework with finding two solutions for measuring and log data from these surges andtransients. One temporary solution where a measurement program has beendeveloped. A second solution where different company solutions have been analyzedto decide which fits best. For these measurement solutions two solutions for bringingdown the voltage has been used.

Hanterbara båtar is a new company who builds alumina boats customized for people in wheelchairs. Due to the fact that the company only built two boats yet, the production documentation is not complete. The drawing that does exist is not in an exact standard which makes production planning harder.The purpose of this work has been to make the production of the boat easier and simplify further development and modification. Product development in the form of optimizing details is also one of the main purpose of this work.This is all done by making a 3D-assembly of all the existing drawings. After this is done new drawings will be made and added to the main assembly.

Purpose: To examine the hearing environment for tattoo artists regarding occupational noiseand to see whether tattoo artists are exposed to hazardous noise according to Swedish WorkEnvironment Authority regulations. Method: Using a dosimeter we measured a total ofseven sessions of approximately one hour on seven different subjects, located on five studiosin Gothenburg. As a complement we did also hand out surveys based on twelve questions toexamine habits, experienced sound environment and to see if there were any hearing relatedpatterns. Results:. Sound level measurements showed that the lower exposure action valueLpAeq,8h 80 dB(A) in one case was reached if applied to the average working time of sixhours.

The Yara N-Tester is a handheld chlorophyll meter which can be used in several different crops as an aid to determine if there is a need of complementary fertilization with nitrogen (N) or not. If the crop requires more N the N-Tester will recommend an amount in kg per ha. The possibility to assess the need of N depends on the strong relation that exists between chlorophyll- and N-concentration in the leaves of plants. In the multiannual trial series ?Nitrogen to winter wheat at different soil conditions? measurements with the N-Tester was carried out at flag leaf emergence (GS 37). In this work the result of measurements, the NTesters ability to estimate the need of N in winter wheat, will be presented for the years 2008-2011.

To be able to measure high-surge voltages and transients with short rise times youneed measuring instruments with a high sampling frequency and large Bandwidth.These surges and transients occur primarily at lightning but can also occur at forexample at connecting errors at an electrical switch-gear. This report describes thework with finding two solutions for measuring and log data from these surges andtransients. One temporary solution where a measurement program has beendeveloped. A second solution where different company solutions have been analyzedto decide which fits best. For these measurement solutions two solutions for bringingdown the voltage has been used.

There have been, in some rare cases, difficulties with clamping of inserts with U-holesin their tool holder. According to the complaints, the inserts could not be properlyclamped or could fracture when clamped. A study has shown that variations inclamping behaviour are mainly depending by the position of the screw hole in the toolholder and the centering of the screw hole in the insert.The focus of this project has been the centering of screw hole in insert. It has beenshown that the screw holes are not always enough centered in the insert. Theproblem may occur after a certain step in the production, i.e.

The building industry consumes approximately 40 % of the total energy consumption in Sweden, where the using stage is dominating with 80 %. There is a lot of work in progress to reduce energy use in the building industry, and the demands from authorities regarding energy use increases. As a part of this work Building and planning department of Sweden has established a requirement that has been applied since 2006, and restricts a maximum energy use for buildings.The requirement includes that an energy simulation must be done in advance to demonstrate that it is possible to meet the demands.Reality is however more complex than an energy simulation program, that frequently underestimates the energy use of buildings. The purpose of this thesisis to study and analyse deviations between estimated and actual energy use in modern apartment buildings. The study includes four apartment buildings in Stockholm, Gothenburg and Jönköping that were built in 2007-2009.

ObjectiveThe objective of this study was to investigate the clinical application to use ASSR in anesthetized childrenDesignOne main ambition of the investigation was to compare hearing threshold using ABR with estimated hearing threshold using ASSR. Another aim was to examine if the duration of an ASSR measurement could be reduced by only using the frequencies 1, 2 and 4 kHz and exclude the frequency 0.5 kHz. This is a retrospective study using electrophysiological measurement from a database.ResultResults showed a high correlation between hearing threshold using ABR and estimated thresholds using ASSR, with the frequency 0.5 kHz showing a slightly lower correlation. Result also showed that the test duration was increased when using all test frequencies in ASSR-measurement compared to when 0.5kHz was excluded. ConclusionThe study showed a high correlation when comparing hearing threshold using ABR and ASSR.

The Swedish government have a goal that wind turbines shall produce 30 TWh by the year 2020, compared to about 3,5 TWh produced in Sweden during 2010. To minimize the disturbance that wind turbines create the Swedish Environmental Protection Agency has stated a guideline value that noise from wind turbines at nearby residents shouldn?t exceed 40 dBA, at 8 m/s wind speed. With advanced calculation models, like Nord 2000, the emitted sound from future wind turbines can be calculated at an early stage to optimize the power production without exceeding the 40 dBA. When the turbines have been built there is a need to verify that they really are within the guideline.

The Private Equity industry has over the past years been booming and major external environmental changes have made the industry transform rapidly. Increased competition between Private Equity firms is one of the reasons why the industry has been and is being forced to focus more on addition of value through increased operational management. Consequently, the focus of value addition is by some said to be transferred away from deal making and financial skills, and into active operative management. This case study investigates how the portfolio management, and more specifically the measuring and management of performance, is carried out in a number of leading Swedish Private Equity funds with investments in the biotech sector. The biotech sector is characterized by extensive research and development, and many biotech companies often lack income and other measurable financial parameters in the initial phase.

A performance measurement system can be used as a means to evaluate past performances and to communicate prioritizations. It has also been proposed that a performance measurement system can serve as a method to execute strategies, guide in operational decisions and constitute a tool for making the organization more efficient. Yet one may question if such a system will ever reach this capacity if operating managers do not utilize it as a management tool, but rather treat it as a mere report in the bunch. This paper explores how middle managers in fact apply performance measures and what obstacles there are to integrating them in the management of subunits. Furthermore it serves to investigate whether these managers experience a conflict between how they are expected to use the measures and what they deem possible to adopt.