This technical report describes the master thesis in material engineering called ?Testing of surfaced hardened materials conceivable for gears and shafts?. The work extents 20 academic points. Land systems Hägglunds manufactures and sells different kinds of combat vehicles and terrain vehicles. Since the demands for bigger and stronger vehicles increases all the time, so are the demands on shafts, gears and other transmission details.

In this project forging of aluminum alloy Al 6026 T9 has been performed in the temperature range of 400 °C ? 470 °C. The alloy which was in the shape of a cylindrical billet was formed in a press with the aim of analyzing the effect of different forging temperatures and required press load for optimal die filling. The component?s dimensions were later measured and compared to a reference piece.

When farm animals are transported there are several factors that can affect their welfare. If the vehicle has an accident the welfare of the animals transported will probably be compromised. The aim of this study was to make a survey of accidents with animal transportation vehicles in Sweden. The survey included the number of accidents from January 2000 to May 2014, the cause of the accidents and how the animal welfare was affected by the accident. The authorities which were likely to have reports about accidents involving animal transports were contacted. There were no collected records about transportation accidents and the authorities referred to eachother for information.

Before the European construction standards were introduced in January 2011, it was mainly themethod in BBK04 that was used for calculating punching capacity in concrete structures, and in lesscommon cases the method in BHB. The method of BBK04 is easy to use and have had the samestructure since the first was published in 1979. The Concrete handbook method (BHB) where usuallyonly used when a higher punching capacity was needed and the cross-sectional height where fixed,calculations using this method entails more work, but will in return usually give a higher capacity. Italso allows the use of shear reinforcement to increase the cross-section capacity. The method ofcalculating punching shear in EC2 differs largely from the methods of BBK04 and BHB.

In this work, a method was developed and evaluated for calculating the life of welds under the influence of fatigue loads from a vibration environment. Typically, a shaker table is used for testing a component against vibration loads. The shaker table creates a vibration environment that is defined in the frequency domain by a power spectrum.Similarly, a virtual vibration table can be used to calculate the same type of load environment, which can then be used to calculate the expected lifetime. The benefit of this method is that it can be used in design, as well as in simulation of tests before physical verification tests are carried out.Today there are methods for calculating fatigue life of non-welded base material, but since many components contain welded joints, there is a need to apply this method to those types as well. To achieve this, the thesis combines two different areas, which together provide a method for fatigue assessment of welds using a virtual shaker table.The methodology is carried out by modeling the component, and its welded joints, in a finite element program.

At the plant of Sandvik do Brasil in São Paulo there is a need for improving the transport of inserts between the plant building and the stock building. The idea is to install a system with an Automated Guided Vehicle (AGV) to take care of this transportation. The purpose of this report is to present which demands there are on the system and to find the best solution according to the demands.To conclude this work a study was made of the plant and the AGV technology was examined. Several providers of AGV solutions were contacted to get information about prices and detailed solutions.The conclusion was that the most suitable system for this application is a small unit load vehicle using inductive wire as guiding system..

Wastewater contains biodegradable materials, which are often measured as BOD7.Trickling filters are sometimes used as a purification step for BOD-reduction. Atrickling filter is a tower, which is filled with a carrier material. Microorganisms growon the carrier material in the form of a biofilm. This biofilm consists mostly of bacteriathat purify water from BOD.In Älgarås? wastewater treatment plant the water is purified by a trickling filter.However the treatment plant has difficulties reaching the emission requirements forBOD.

This Master thesis is about a postal- and telegraphic building in Eskilstuna, Sweden. The construction methods for the specific building and buildings in general from the same time are described. The purpose of the report is to describe the loads acting on the building and how it has been built and why it has been rebuilt during the years. After this, possibilities of reconstruction and adaptation for today?s demands can be evaluated.

In conventional viscose manufacturing, a large amount of carbondisulfide is consumed. This amount has to be decreased to keep the production cost down and to reduce the environmental impact. The purpose with this work was to show if an enzyme treatment of a dissolving pulp could increase the degree of substitution in the viscose so that the amount of carbon disulfide consumed in the process could be decreased. Previous investigations by Kvarnlöf (2007), Engström et.al. (2006) and Henriksson et.al.

The goal of this thesis is to design an attachment between a duct and a pod. A pod is what could be compared to an outboard engine for larger vessels. The pod is placed on the outside of the ship?s hull and can rotate 360 ?. A duct is a large steel ring that can be placed around the propeller on the pod to increasethe propulsion force of the ship in lower velocities.

The aim of this study was trough qualitative interviews with teachers and counsellors in Swedish schools, to study their experiences and perceptions of non suicidal self-injury (NSSI) in adolescents. During the study three teachers and three counsellors who worked in four different schools were conducted. The theoretical approach that was used is Michael Polanyis theory tacit knowledge. The outcome of the study was that schools did not seem to talk about NSSI as a problem and the teachers knowledge about it had come from own experiences meeting adolescents whit NSSI. The interviewed teachers and counsellors felt it hard to define NSSI, they mainly referred it to someone who cut themselves.

At the moment in central Täby there are small district heating network operated by Fortum Heat. The distribution network has an annual heat demand of about 70 GWh, which is supported by the network's two plants, Galten and Farmen. Täby as a region is rapidly growing and there are grand plans to develop the area. Estimated market potential for a future district heating expansion in Täby is very high and as early as in 2007 Täby decided to invest in a large-scale expansion. In autumn 2009 Täby did a procurement process, known as the ?Täby initiative?, to find a partner that could implement those expansion plans. To secure a cheap basic production the partner also need to build a power plant at Hagby recycling center. Despite high interest during initial state of the process, only one procurement offer were received and Täby suspended the contract in March the following year.

Both the German and the Nordic power markets are seeing dramatically changed conditions due to an ongoing process of expanding the share of renewable production in the systems. For the German part this comes from heavy subsidies which have led to an explosive development in installed capacity of photovoltaic and wind based production. After the Fukushima incident it has been decided to shut down all Germanys nuclear plants. This capacity drop is however not of the same magnitude as the increase in renewables, but will impact the stability of the power system. The Nordic power system which already has a surplus of power sees an even further increase, coming mainly from construction of new nuclear plants in Finland and a general increase in wind farms.

The aim of this report is to give a description of a diploma work of 20 points that has been performed during the spring 2006 at Ericsson AB in Borås. The report accounts for the problem and procedure during the diploma work. The software used for this project was embedded in a radio link. The RAM in this radio link was divided into several regions where two were used for memory allocation. The current allocation of memory in the radio link was not optimized with regards to performance, security and memory use and the configuration used made it difficult to determine the memory use of the system and the actual memory need.

When a combined heat and power plant produces heat and power it often faces a deficit of heat load during the summer or other periods of time. This heat is often unnecessarily cooled away or the power production has to be reduced or shut off. If it is possible to store heat from periods with low heat demand to periods with high heat demand one can get many benefits. Among these benefits are: increased power production, decreased operation with partial load, uniformly distributed load.To be able to store heat in situations like this long-term thermal heat storages are needed. In this thesis five different types of stores are presented: rock cavern storage, tank storage, pit water storage, borehole storage and aquifer storage.