The study was carried out as a time study of five wood chippers placed on trucks,so?called huggbilar. They are trucks with built?in wood chipper, chip bowl and crane pulling a chip trailer. The system is used for chipping wood fuel, transporting, and delivering the chips to heating plants.

A third party access to district heating networks has been proposed in Sweden, to increase the competition on the district heating market. Such third party access could create opportunities for the agricultural sector as an energy producer. This study describes the technical, economical and environmental prerequisites for a farmer cluster to build and run a heating plant, fueled with local wood fuel. The heating plant in the described scenario is 8 MW and will supply a village of 1000 houses, and is fueled with wood chips exclusively. Supplying a heating plant with fuel puts high demands on the logistics, since there need to be a continuous flow of fuel. In the scenario, wood residues from felling and thinning is stored in stacks in the forest, and a few times a year chipped and transported to a storage area at the heating plant. In the study, an estimation of the profitability has been made by estimating the cost of the investment, personnel, operating and maintenance costs and costs for the fuel and ash handling.

Sweden recently changed the national regulation of chimney sweeping. This study has two purposes. The first purpose is to evaluate the effect of this reform to see if the new regulation has led to an effect in terms of increased chimney fires in single-family houses and for the wood-burning and oil-burning stoves, respectively. The second purpose is an updating of a previous study (Mattsson 1994) of analysis of society´s benefits and costs of different alternative sweeping frequencies for wood-burning and oil-burning stoves. This study also has a secondary purpose to examine the extent to which the local sweeping rules vary with climate conditions.  Mattsson, based on his results, proposed that the sweeping requirements for oil-burning stoves should be reduced from twice a year to once every second year and for wood-burning stoves the sweeping should be reduced from four times to once each year.

This report is a thesis for collegeengineering program in structuralengineering at Uppsala University andwas commissioned by the Swedishcontractor Svevia. The study aims toprovide an overview of the mostbeneficial bridge material from bothenvironmental and economic point ofview.The life-cycle analysis covers onlycarbon dioxide emissions, since it isthe most spoken of in today?s climateagenda. Furthermore, this study aims tohighlight which parts, of the systemboundary, that contributes to greatercarbon emissions for the wood- and theconcrete bridge.The life-cycle cost analysis wascalculated with a lifespan of 40 yearsand covers the basic cost of investment,operating and maintenance, anddecommissioning costs.The analyzed constructions in this studyare existing projects that are almostcompleted. Both bridges were designed tohandle loads up to 60 tons.

The costs of logging and of transportation with truck are dominating the total cost of wood delivered at industry. To support the profitability for the members' forestry the processing and handling with the timber has to be as efficient as possible. Increased length of pulpwood in thinning is one conduct that can result in higher productivity and/or lower costs. The study is scaled as a system analysis with the aim to exemplify the differences between working with 3- and 4-meter as standard length of pulpwood, related to biological aspects, timber receipts, cost of logging and cost of transportation with truck. Important aspects are if the change is technically and biologically feasible and economically profitable.

The aim of the study was to compare productivity in first thinning of birch stands, when either energy- or pulpwood was harvested. The systems total profitability was also compared by including forwarding and chipping costs. A Gremo 950 HPVR harvester was used and the same driver was used under the entire study. During the pulpwood harvest a Logmax 4000b harvester head was used and a feller buncher head made by Silvatec was used during the energy wood harvest. Six study unit pairs were located in a birch dominated stand outside Ängelholm in Skåne.

The primary purpose of this study has been to investigate the Swedish timber industry?s perception of compression wood. A secondary aim has been to describe particular areas within the production process where compression wood is likely to cause problems. This study has mainly been carried out as a questionnaire. In order to connect the findings to current research, additional information has also been collected by means of a literature review. The questionnaire has been intended for sawmills and wood-manufacturing companies from various production classes and owner categories, as well as from different parts of the country.

Summary Today energy prices are rising. As a result biomass fuel is getting more and more interesting. Wood chips is very popular, but also straw from grain production is on the table. Lunds Energi AB project a combined power and heating plant in Örtofta out of Lund. Wood chips is meant to be the main energy source, complemented by straw. In this thesis the transportation of straw for fuel is studied.

A high amount of dead wood is one of the most important prerequisites for high biodiversity on forest land in Sweden. Dead wood is most abundant in young forests, thinned forests, woodland key habitats and protected forest land. In old-growth forests most of the dead wood consists of logs and snags, whilst in managed forests a huge proportion of dead wood is made up of logging residues like stumps and FWD, fine woody debris (< 10 cm diameter). All these different types of dead wood may serve as substrates for epixylic bryophytes and lichens. However, few studies have been conducted on the relative importance of these different fractions of dead wood for the occurrence of bryophytes and lichens, especially when considering dead wood on thinned forest land.

As demand for renewable energy is increasing rapidly, the market for biomass pellets is expected to continue to grow in the near future. Most of the new raw materials that are discussed for pellet production have one thing in common; the production costs will increase compared to using traditional raw materials such as sawdust and planer shavings. The aim of this thesis is to investigate to what degree increased use of new raw materials for pellet production will affect the general pellet prices in Sweden and to survey what plans Swedish pellet producers have concerning new raw materials. To investigate the raw material situation of the Swedish pellet producers an industry survey was performed. Literature studies were also made on previous research in the subject field. Calculations of the production costs for pellets were done for the raw materials sawdust, wet sawmill chips and energy wood respectively. New raw materials are already used by the large-scale pellet producers in Sweden.

If you have access to wood, a wood burning boiler is a cheap way to heat your home, but it is certainly not the most convenient option. Wood requires many operations and management, which takes time. One way to reduce this workload is to have a modern boiler with automatic ignition. Enertech/CTC has a desire to create an accessory with automatic ignition to a modern wood burning boiler. Today there is no boiler on the market that can ignite firewood automatically without the introduction of paper and sticks.

The purpose of this thesis is to study whether there is a demand for sawn wood products of large dimensions and planed goods among Wallnäs AB:s customers. The thesis consist of two main parts, one survey among Wallnäs present customers and another one which purpose is to increase Wallnäs customer base. Finally there is a chapter that describes what properties the raw material has to have in order to produce the demanded products. The survey to the present customers was conducted through a questioner. A sample of those who stated an interest for either sawn wood products of large dimensions or planed goods, were later contacted for a telephone interview. To reach out to new customers, relevant companies has been identified through the Swedish Trade Councils data base and through the member list of the Timber Trade Federation.

Calculations are an important part of planning around a construction project. From concept to completion of the project calculation is a tool to try to predict the actual cost. During the production stage in particular, deviations occur which makes the actual cost different from the calculations.This thesis is done in collaboration with JM Residential Stockholm. The study includes a cost follow-up in which a comparison was made between the calculated production cost and actual cost for the five projects. The aim of the study was to observe the most common reasons that a project deviates from the calculated production cost and then summing these causes in a number of categories.

Does goodwill affect the cost of capital? Goodwill is an asset which is characterized by much uncertainty regarding both what it is and how much it is really worth. Based on economic theory about information risk and principal-agent problems as well as theory regarding the cost of capital we test for the hypothesis that debt and equity investors perceive goodwill as something risky and hence demand compensation for taking on this extra risk. The proxies used for the cost of capital are cost of debt, beta and the EP-ratio. On a general level we find that increasing the level of goodwill seems to result in higher cost of capital as represented by the three proxies.

Most of the saw and pulp industries have stored wood nearby their production, the main reason is to have a continuous wood flow to the production. Wet storage of wood is of great importance to keep the wood quality. Without water sprinkling the risk of drying outand decomposition through biological activity increases significantly and will result in a negative effect on future production and quality. One drawback of wet storage of wood is the leaching of chemical substances into the surrounding recipient. The log yard run-off contains phosphorus, nitrogen, phenols and organic substances. These substances can cause problems for the surrounding environment. The main objective of this project is to gain an understanding of the wet storage used by the Swedish wood industry and estimate the environmental consequences that run-off water will have on the recipient.