Throughout its wide distribution in the northern hemisphere, the golden eagle occurs in a diverse range of environments, e.g., mountainous, forest and open areas. The literature on juvenile golden eagles is limited, and this study provides further knowledge on habitat use and ranging behaviour during the post-fledging period in boreal Sweden. A total of 14 golden eagle juveniles were tagged with GPS transmitters during 2010 and 2011, and nine could be followed during the entire post-fledging period from fledging until migration. The juveniles fledged at the end of July and beginning of August and initiated migration during October and beginning of November. The length of the post-fledging period, until migration started, ranged from 49 to 97 days. During this period, the juveniles? distance from their natal nest and their GPS height increased with time as their flying abilities developed.

Today there is no way of measuring or simulating turbulent flow in high Reynolds numberenvironments. The computational power required to simulate these conditions is not expectedto be available for several decades so instead the CICLoPE project aims at solving thisshortage by the construction of a long carbon fiber wind tunnel in which real measurementscan be made. To do accurate measurements it is of importance that the wind tunnel, 0.9 metersin diameter and 110 meters long, is as straight as possible.This master thesis treat the design and construction of a device which may be used to align thetunnel along a reference laser beam. A design is presented which allows the pipe to be alignedwithin about a quarter of a millimeter along its entire length. Contents span over severalscience fields such as physics, mechanics, control theory and electronics.The result is a theoretically correct design.

In the growing concern for the state of the environment more tools are being integrated in the decision-making processes. Sweden actively makes use of environmental impact assessment (EIA), which is supposed to minimise negative impacts of a project, policy or plans on the environment. The EIA process in Sweden still requires certain improvements to be more efficient. In this study actor interaction was analysed with trust being the framework for analysis. The aim is to find out whether it is possible to use trust as a framework for analysis since trust research is very discipline dependent.

Wind is used as an energy source all over the world. To be able to use this effectively, there is a need for as good forecasts and forecast models as possible. One of these models is Coupled Ocean/Atmosphere Mesoscale Prediction System (COAMPS®) that is used to calculate short time forecasts. This model is used here to calculate wind speeds at two different areas in Västra Götaland, Bengtsfors and Vänersborg. There are also wind measurements with SODAR stations for these areas.

Gestaltningsförslag till nybyggd villa i Kivik med hänsyn till i huvudsak ståndorten. Tomtens öppna läge göra att den är utsatt för stark vind och marken består till större delen av sand, vilket ställer ett högre krav på det valda växtmaterialet. Omgivningen består av hästhagar, ett villaområde från 70/80-talet och ett ljust och öppet läge med naturen som bakgrund, vilket har en stor påverkan på trädgårdens design. Huset har en modern arkitektur och skiljer sig från den övriga bebyggelsen och utmaningen har varit att integrera detta till den övriga omgivningen med hänsyn till den speciella ståndort som finns på platsen.

The aim of this master thesis was to find and grade suitable sites for Wind turbines in the rural district of Lerum at the reguest of Göteborg Energi. The rural district of Lerum consists of very complicated terrain which was the reason why we picked Lerum.The assignment was achieved by using the software program ArcGIS and its attendant tools. In step 1 an overall analysis was made in order to sort out the least suitable sites. Step 2 consisted of a 3D analysis in ArcScene together with a more precise analysis in ArcMap. As result we found two interesting sites, which met our demands and specific constraints.

The purpose of this report is to investigate and compare the difference between stand-thinning machines and strip-road thinning machines, and how they affect the stand on behalf of future growth, theoretical economic result, wind impact, snow pressure and density of stand. The investigation is regarding the first commercial thinning of pine stands, after pre-commercial thinning that was well conducted. The investigation area was located near Katrineholm, Sweden. The measurements that were measured were strength of thinning and amounts of wind throws, snow-breaks and hauling damages. The results that emerged, was that thinning with strip-road machines had a significantly higher strength of thinning over all, as compared with the stand- thinning machines (45 percent versus 30 percent). Comparisons between wind-throws, snow-breaks and hauling damages of the stand could not establish any significant differences between the two methods that were investigated. Conclusions, over all, were that if forest owners want to have more timber volume left for second thinning and final cut of the stand, the forest owners should choose the method with stand-thinning machines. From the point of view of gentle treatment of the stand and ground damages the choice should be the same. However, the method with strip-road thinning machines is the most common and accessible method in Sweden. Most likely it is the most economical way to manage the stand for forest owners in present time. If the method with stand-thinning machines is becoming more common in Sweden, it is suggested for forest owners to consider the stand-thinning method as a candidate for treatment due to economic aspects..

The company Sol & Energiteknik wanted to examine the possibility to make a standardhouse totally energy independent. Based upon this I have, during the spring of 2007,examined the possibilities available at the market today through litterature studies, contactwith several companies and reading reports at the internet.The first thing to examine has been to determine the energy consumption for a standardhouse, and find out if there are better technologies to be used for energy conservation.My conclusion in this matter is that there are possibilities today for building a house moreenergy efficient.When I had reached the point at which my design for the house was decided, I also hadto choose the different products to use to produce energy as well as to store that energy.To produce heat and electricity to the house I decided to use a Wind turbine and a solarwater heater.The most difficult part of designing a house that is energy independent is that theproduced energy must be stored somehow. Storing the heat is relatively easy beacuse theheat can be stored in a large water tank. The electricity is a bigger problem beacuse itmust be stored in batteries, which today are too expensive to be used in a standard house.In the future producing and storing hydrogen might be used to produce electricity, buttoday that technology is both expensive and not tested enough.My final conclusion is that a standard house can not be built to be totally energyindependent today, unless it is very expensive to connect the house to the electricitynetwork. As an alternative solution I came up with a proposal for a house which isconnected to the electricity network and have some amount of own produced energy.This house prooved to be a good investment if you choose to build it today, and it couldbe a very good investment in the long run beacuse energy prices increase every year..

This master thesis comprises analysis and dimensioning of a keyed joint between a generator axis and a hub with aid from the FEM-software ANSYS Workbench 13.0.The generator axis is a part of a hydroelectric power station that generates electricity with a reactions turbine, a Kaplan turbine. The existing keyway consists of one parallel key with the width 90 mm and height 45 mm. Due to a planned increase of the power of the generated power with 32 % a design study was needed to see if the keyed joint would be suitable for the extra force. Because of the fact that the axis diameter is bigger than the standards covers/recommends a the keyway had to be re-dimensioned. In an earlier assignment from Skellefteå Kraft AB to Sweco Energuide the keyway was planned to be properly dimensioned, but no final solution was approved.During this master thesis a number of different numerical tests were made.

This master thesis comprises analysis and dimensioning of a keyed joint between a generator axis and a hub with aid from the FEM-software ANSYS Workbench 13.0.The generator axis is a part of a hydroelectric power station that generates electricity with a reactions turbine, a Kaplan turbine. The existing keyway consists of one parallel key with the width 90 mm and height 45 mm. Due to a planned increase of the power of the generated power with 32 % a design study was needed to see if the keyed joint would be suitable for the extra force. Because of the fact that the axis diameter is bigger than the standards covers/recommends a the keyway had to be re-dimensioned. In an earlier assignment from Skellefteå Kraft AB to Sweco Energuide the keyway was planned to be properly dimensioned, but no final solution was approved.During this master thesis a number of different numerical tests were made.

Housing construction very close to the lake Mälaren has become very popular today. One potential problem with these houses is the influence of the sea climate. Unprotected buildings are affected by strong winds and precipitation. So for that reason, it is very important to make an accurate climate investigation and use it for decision-making during the planning of the new settlement.It is very important with a good moisture protection regarding pelting rain, that is the combination of wind and rain. This is more important for buildings close to a lake, as this location normally means a higher exposure to wind.

This paper aims to explore the phenomenon urban wind energy, its visual effect on built environment and the factors that affect the opinion towards new elements in the city. A place study of the city Gävle serves as a complement to the theoretical part of the paper. The theoretical discussion opens with an account for the technical and economical conditions of urban wind energy. It presents the technical basics, different types of turbines and a discussion occurring wind related techniques in built environment. Today, the knowledge of how the wind moves and acts in the rural landscape is quite good.

Both the German and the Nordic power markets are seeing dramatically changed conditions due to an ongoing process of expanding the share of renewable production in the systems. For the German part this comes from heavy subsidies which have led to an explosive development in installed capacity of photovoltaic and wind based production. After the Fukushima incident it has been decided to shut down all Germanys nuclear plants. This capacity drop is however not of the same magnitude as the increase in renewables, but will impact the stability of the power system. The Nordic power system which already has a surplus of power sees an even further increase, coming mainly from construction of new nuclear plants in Finland and a general increase in wind farms.

The purpose of this paper is to understand the climate of the street and how it can be modified to better meet the needs of the street and the user groups. At the same time the conditions of the street and its surroundings also has to be taken into account. To accomplish this it is necessary to have a broad knowledge of the climate conditions in the city. Therefore an overview of the climate elements and how these are modified in the built-up areas are given. The part of the paper which deals with the city climate has a global approach to be able to give an as complete picture as possible.

This project has revolved around finding better ways of overseeing vibrations of the gearbox at a wind power station. The gearbox has been a huge problem at the stations located at Gässlingen and the sooner the warning of an incoming breakdown is at hand the more money you can save from preparations. The work has been carried out together with Askalon AB in cooperation with consults from ÅF. Askalon is a company with a department focused on overseeing vibrations and it is in collaboration with that department the work has been carried out. During this work, new positions for the sensors and new methods of gathering and analyzing data have been worked out. This was then implemented at a wind power station to be tried out on site.