This bachelor thesis contains the findings of an investigation into the laying of wedge sawn wood flooring. The advantage of Wedge sawn wood flooring is the usage of more material from each board reducing waste. The boards follow the natural profile of the tree where the root part of the board is wider, and the top part is narrower. The technique involves placing boards side by side with adjacent boards in opposite directions. The thick base of one board is neighbored by the narrow top of another, this creates a pattern of wedges in alternating directions, known as a ?root and top? system. Existing literature into this type of flooring is sparce.

The purpose of this study is to explain how the value of sawn wood changes when sawn wood are cut in 30 respective 60 cm lengths. The raw material into the saw mill will mainly be bucked in 30cm and 60 cm modules. There will also be two alternatives where the timber will be bucked special lengths, 370, 490 and 550 cm but also in 490 and 550 cm.The method used for the study is to simulate both cutting and sawing the woods. For cutting the simulator Timan is used and for sawing the simulator Timberopt is used. When data is generatedfrom the simulators, calculations of some key figures is done and also how much the revenue need to be increased for the sawn wood in order to cover for the increased costs of changing sawn woodfrom 30 cm to 60 cm modulesThe conclusion is that the single biggest reason, impacting the value of the sawn wood is the cutting at the saw mill.When going from 30 to 60 cm modules, the impact will be that the customers to the saw mill must pay more to increase the revenue by at least 10% for the sawn wood in order to justifice the changein production.It is also possible to increase the value of the products further by bucking the timber in three lengths, 370, 490 and 550 cm, in order to get 12 % increase of the share of longer sawn wood (>= 480 cm)..

The purpose of this thesis is to study whether there is a demand for sawn wood products of large dimensions and planed goods among Wallnäs AB:s customers. The thesis consist of two main parts, one survey among Wallnäs present customers and another one which purpose is to increase Wallnäs customer base. Finally there is a chapter that describes what properties the raw material has to have in order to produce the demanded products. The survey to the present customers was conducted through a questioner. A sample of those who stated an interest for either sawn wood products of large dimensions or planed goods, were later contacted for a telephone interview. To reach out to new customers, relevant companies has been identified through the Swedish Trade Councils data base and through the member list of the Timber Trade Federation.

The survey aims to shed light on traditional and contemporary bottom floor frames, their construction and different insulating materials; mineral wool, wood shavings and charcoal. The purpose is to analyze and discuss the similarities and differences as well as the pros and cons with a focus on the construction and the different insulating materials. The work has been limited to comparing two different wooden floor frames. The first one is based on a real floor frame from an older building, this example is presented as the traditional floor frame in this study and are from around 1940. The other floor frame is presented as a contemporary floor frame and is based on wood building type descriptions and literature.

The primary purpose of this study has been to investigate the Swedish timber industry?s perception of compression wood. A secondary aim has been to describe particular areas within the production process where compression wood is likely to cause problems. This study has mainly been carried out as a questionnaire. In order to connect the findings to current research, additional information has also been collected by means of a literature review. The questionnaire has been intended for sawmills and wood-manufacturing companies from various production classes and owner categories, as well as from different parts of the country.

Wood has always been an important material for people, and it is used for many applications. As for example, fuel for cooking and heating houses, construction materials and for constructing means of transport. Since wood also is a material that with time biologically degrades due to activity by micro organisms and wood fungi it is important to find ways to protect and further lengthen the life span of the material when in service. One method is to decrease the amount of water in the material by impregnation with an hydrophobic oil. The Linotech method which uses only pure linseed oil is one such possible method. The aim of this study was to investigate the possibility to at the same time impregnate and stain/colour wood samples of pine and spruce by using the Linotech method.

The need of raw material does of course fluctuate but the long term view is an increasing demand due to the growing consumption of sawn timber products, pulp, paper and lately also biomass. This has led to a keener competition for wood. At the same time there is an ongoing structural change of a significant part in the Swedish wood supply market, the private forest owners. In 1992, 22 % of Sweden´s 335 000 private forest owner lived apart from their forest. In 2007 this figure had risen to 36 %.

Modern sawmills are using the raw-material and the production-capacity more efficiently today, due to rising raw-material prices and higher production costs. Log sweepness has a negative effect on the sawn yield, for sawmills with straight-sawing. It is desirable that these logs could be sorted based on more criteria, if it increases value-yield and consequently the utilization of raw-material. Bow-heights over 1 cm have a negative effect on sawn yield, since the surface of the mantle cuts down in the sawn pattern. Some of these small bow-heights reduce the logs yield of value which affects the production planning negatively. Nearly half of all the Swedish logs have a bow-height over 1 cm.

The courts international juristiction within the European union is regulated by the Brussels I Regulation. Article 2.1 of the Brussels I Regulation contains the fundamental provision. According to this Article the plaintiff shall submit an action where the defandent is domiciled. The Regulation provides exemptions to the this provision in Article 2.1.The court of the international case can also be determined according to Article 5 (1) of the Brussels I Regulation. This Article contains an alternative to the general provision within Article 2.1.

This thesis is about making a support for barcode readers and RFID readers on a computermounted in heavy vehicles. The computer has several applications designed for heavyvehicles such as an order handling application. The goal was to suggest an architecture toimplement a support for the readers. The architecture should be independent of whichmanufacturer who has made the reader hardware that was connected to the computer.At first a theoretically study was made around RFID technology and standards for thetransport and supply sector. Then the architecture was developed and a demo implementationwas made.The conclusion of this thesis is to implement support for barcode readers with a wedgeapplication.

The aim of this thesis is to find a statistical model that sort logs according to a predicted modulus of elasticity on the sawn boards. The input parameters for the model are X-ray variables from an X-ray scanner. For some of the log classes sawn at the sawmill it is desirable to have a narrow distribution of modulus of elasticity on the sawn boards. 250 pine logs from five different diameter classes were numbered and followed through the sawmill process. Log data were collected from X-ray and 3-D scanners in the log intake.

The aim of this thesis was to analyse BARO WOOD AB:s timber measuring and quality sorting and to evaluate the analyse program Stockholmen. The purpose was to get a better understanding for the quality sorting made at BARO WOOD AB today, analyse differences in center board quality from logs with a good quality and logs with a bad quality, suggest new sorting criterias developed from analyses made with Stockholmen and to evaluate the program Stockholmen. All analyses are based on data gathered in a test sawing made at BARO WOOD AB in June and July 2002. The test sawing was made on four different diameter classes and every diameter class consisted out of A or M-grade logs, with a better quality, and B-grade logs with a lesser quality. The logs where sorted out with BARO WOOD AB:s existing quality criterias.

The purpose of this thesis is to examinethe possibilities for adding a floor to anexisting building using the two materialswood and sheet metal profiles as the loadbearing structure. An apartment buildingfrom the 60s has been used as referencehouse. Two different suggestions for thedesign are presented in the rapport. Oneof them has been analyzed with wood andsheet metal as the load bearing structure.Using the old constructional calculationsand blueprints of the existing buildings,the load bearing capacity has beencalculated. In the calculation programFEM-Design the building has been testedwith the loads that an extra floor wouldgive.

The equine hoof is often manipulated in purpose to achieve a better stride or to reduce the weight on damaged tissue. The living tissue in the hoof can?t store energy as glycogen and is therefore depending on a continuous supply of glucose for its energy production. The purpose of the study was to determine if wedging (i.e. elevating) the heel could influence the hooves glucose and lactate consumption/production. Five standardbred horses were trained to trot on a treadmill without getting physical or mentally tired.

This study has investigated what makes a business relation satisfactory. The purpose is to distinguish the factors that are relevant to a functioning cooperation relationship between sawmills and DIY-stores. The theoretical framework is primarily based on long-term business relationships. The study is based on two case companies and their relations with wood-suppliers. - Case company 1 is a relatively new established and still growing company.