Rooted in Industrial Ecology (IE) theory, this report evaluates how urban agricultural concepts and techniques, can contribute to improved ecological sustainability within the inner city boundaries of Stockholm. An overarching literary study as well as an interview was carried out, resulting in a qualitative analysis followed by suggestions for practical implementations. A substantial convergence was found between the eco-restructuring objectives of IE and the principal motives for urban agriculture. Consequently, eco-restructuring objectives are found in varying degrees in the presented urban agricultural techniques. Industrial symbioses, permaculture and combinations of urban agricultural techniques are tools which are capable of corresponding adequately to the diversity of urban settings.

This paper examines the power producing dams along the Ume-river as an integral part of and a result from the urbanization process in Sweden during industrial capitalism. The aim of the paper is to contribute to the knowledge of the urbanization process in Sweden in general and of its traces along the Ume river in the county of Västerbotten in particular. The paper applies the theory of concentrated urbanization and extended urbanization put forward by Neil Brenner and Christian Schmid (2015) and argues that the building of power producing dams along the Ume-river is part of an extended urbanization process. This becomes particularly evident when examining the vast physical structures that is the dams, situated in an otherwise remote and sparsely populated area. These vast physical structures are also very well connected to a nation wide electric grid that has connections to bordering countries as well.

Seabased Industry AB develops system for extracting electrical energy from ocean waves with a Wave Energy Converter (WEC). The components is bought from subcontractors and then assembled into wave energy converters, buoys and marine substations by Seabased. In the future Seabased will produce more of the components themselves to reduce costs and to have better control over tolerances. The production line will also include the painting of the WECs and substations, which is performed in a painting line.The purpose of this thesis work is to study what is required to build a painting line, regarding the types of stations, transporting types and the space needed. This will result in layouts for the painting line.To receive the necessary information about production theory and corrosion and surface treatment, literature concerning this area has been studied.

Surface lift adapted for today?s user Today?s T-bar lift looks almost the same as when it was launched in 1938, even though a lot has happened in the ski and mountain industries. New equipment has developed without any major adjustment to the lift. Snowboard, sit ski and downhill biking are just some examples of the evolution that demands new seating positions. It?s also very common for families to spend their holidays in the mountains nowadays.

I detta examensarbete har en tillförlitlighetsmetod tagits fram som väger samman kostnadspåverkande faktorer för investeringar och underhåll i eldistributionssystem med kostnader förknippade med avbrott. Syftet med metoden är att möjliggöra för nätplanerare och projektörer att jämföra olika investeringsalternativ för att kunna kostnadseffektivisera investeringarna i eldistributionssystem. Med tillförlitlighetsanalys kan den förväntade avbrottstiden i systemets uttagspunkter beräknas. Kopplas en kostnad till den förväntade avbrottstiden i uttagspunkterna kan den förväntade avbrottskostnaden för distributionssystemet beräknas. Syftet med simuleringarna har varit att undersöka om det går att minimera den totala kostnaden, investeringskostnader samt förväntade avbrottskostnad, genom slumpvisa investeringar i systemets ledningssektioner. Simuleringarna har genomförts på ett fiktivt mindre system.

Det här examensarbetet har utförts på uppdrag åt Trollhättan Energi AB (TEAB). Examensarbetet är en utredning beträffande förutsättningar för sammankoppling av TEAB:s och Hjärtum Elförenings elnät.De nuvarande ledningsnäten har radialnät och det innebär att det endast har inmatning från ena ledningsänden. En sammankoppling skulle ge möjlighet till sektionerad drift vilket innebär inmatningsmöjligheter från båda ledningsändar. Det gör att ledningsnätet blir mer säkert, tillförlitligt och effektivt.Ett förslag på ett nytt ledningsnät där delar av TEAB:s och Hjärtum Elförenings ledningsnät är sammankopplade har tagits fram. Med det nya förslaget blir ledningsnätet mer driftsäkert och uppfyller lag- och myndighetskrav.Beräkningarna som ligger till grund för arbetet är teoretiskt utförda.

Together with NCC and Sweco we measured the air-flow on a semi-detached house in Jönköping. When a pressure measurement is made, the house gets exposed to over- and under pressure. This is done in order to examine the houses climate shell. The climate shell of the semi-detached house we tested exceeded the required air thickness in BBR-2002, hence, measures have to be taken.This report also displays the importance of building air thick houses and what consequences a non air-thick house can have for the ones residing the house. A discussion of different measures is on for the addressed problems with the flow-measurement and the alternative construction-solutions.Furthermore we have described in this report of how to account for the performance of the air pressure, what kind of equipment we used and how we came up with the results.

The aim of my thesis was to do a Life Cycle Assessment (LCA) of an average thread tap that is manufactured by Dormer Tools AB, and to create a practical model that the company can use in order to study other thread taps from an environmental perspective.The method of LCA is used to investigate the environmental effects of a product during its life cycle. This is a gate-to-grave analysis with focus on steel and thread tap manufacturing, coating procedure, use, waste management and transports. Three common coating types were compared separately. Steel manufacturing answers for the highest energy and raw material consumption under the life cycle of the thread tap. Its emissions contribute to global warming, acidification and eutrophication above others.

The energy consumption continues to increase as the use of electronics and energy consuming equipment increases. The use of fossil fuels has to be phased out for this to be sustainable in the long run while the use of renewable energy continues to increase. A renewable energy source is solar energy but the production of heat and electricity are today very expensive compared to other energy sources and an important task for the solar energy market to grow is therefore to minimize the production cost of the solar collectors while increasing its efficiency to produce heat and/or electricity. One way to convert solar energy into heat is by using solar collectors and electricity can be produced by utilizing the produced heat, or by applying solar cells.This thesis aims to recommend a reflective material for the next generation solar collectors from Absolicon and to recommend a commercially available coating for the receiver tube of the solar collector. A market study has been carried out to investigate the cost-related aspects along with the optical and durable aspects for the optical material of the solar collector.

Denna rapport behandlar automatisering av statorlindning vid monteringsline 4 för elmotorer på ABB Motors AB i Västerås. Målet med projektet var att hitta ett lönsamt sätt att automatisera delar av elmotormonteringen. Arbetet begränsades till att omfatta monteringsline 4 där motorer av storlek IEC 200- 250 monteras, dessa är de största motorer som produceras i Västerås. På grund av relativt små volymer och en omfattande variantflora måste en automatisering vara flexibel. För att nå en fungerande automatiserad lösning behövde flera praktiska materialhanteringsproblem lösas.

This project was conducted on behalf of the organization SABO (Swedish Association of Public Housing Companies). The aim of this project was to investigate which relevant environmental aspects and indicators there are for housing companies to present in their sustainability report. The project consists of three main goals: to decide if there is a need for common guidelines when conducting a sustainability report, determine appropriate environmental indicators and to create a simple model of how the companies can present them. This was done by a literature study, analysis of 13 sustainability reports and interviews with seven housing companies. The result of the project suggests that there is a need for common guidelines to, among other things, make it easier to make a comparison with other companies.

The aim with my work is to get a deeper knowledge about the preschool's views of environmental work. I also want to examine how the preschool teachers along with the children work with the project Green Flag in the preschool. I have used structured interview with two teachers in a preschool that works with Green Flag. Green Flag is an environment certification and is an evidence on that one works daily with a document aimed environmental work along with the children. I have found out that each year they work with different themes within Green Flag.

The production of cut flowers has diminished in Sweden and the remaining growers produce mainly in greenhouses. This situation could be changed if hardy, garden perennials suitable for Swedish conditions were to be used as cut flowers. A grower with suitable equipment as plastic tunnels or houses would be able to provide florists with an attractive assortment of perennials for cutting, during an extended selling period compared with the natural flowering period for these cultivars. This assortment would be based upon imported perennials already used by florists, but would also contain new products. To investigate the demand for locally field grown perennials as cut flowers, an inquiry took place.

Radio Frequency Identification, RFID, is a convenient way to enable contactless identification which does not require any physical nor optical contact. As with any radio-based communication the signal can be intercepted, thus making the technology vulnerable to several kinds of attacks. Interception of communication is not the only threat. Since RFID tags might contain personal information or information that will grant the owner access to secure areas, skimming and spoofing attacks are also major threats against this technology. In this thesis report,  the perspective of an adversary is portrayed in an RFID-enabled environment by presenting where RFID is used and how it could be abused.

The development in electronics increases the demand for good design methods and design tools in the field of electrical engeneering. To improve their design methods Ericsson Microwave Systems AB is interested in using computer tools to create a link between the specification and the implementation of a digital system in a FPGA. Xilinx System Generator for DSP is a tool for implementing a model of a digital signalprocessing algorithm in a Xilinx FPGA. To evaluate Xilinx System Generator two testcases has been designed. The testcases are selected to represent the FPGA designs made at Ericsson Microwave Systems.