The project was performed at SiemensIndustry Drive Technologies with theobjective to provide actual values forthe energy savings potential withinSiemens scope of practice.In Sweden the electrical drives standfor about 30 % of the total electricityconsumption and about 60 % of theelectricity consumption within theindustry. During the pre-study phaseelectrical drives with pump applicationswere identified as large energy users.Because of this a case study at one ofSiemens customers, Stora Enso Fors wasperformed. The system that was evaluatedduring the case study was a throttledsystem with a centrifugal pump forpumping pulp.The results yielded that a saving ofover 50 % could be achieved by replacingthe throttle valve with a variable speeddrive, a frequency converter. Thepayback period was two years and twomonths and the present value for thetotal life cycle cost of the variablespeed system was 662.566 SEK lower thanfor the throttled system. As aconsequence, Stora Enso Fors is advisedto invest in a frequency converter forregulation of the system.The general conclusion is that a focuson system efficiency is the mostimportant factor in energy efficiencyprojects and that the system regulationmethod has a large impact on the overallsystem losses and hence its efficiency.Energy efficiency potential forthrottled systems with centrifugal pumpsis large and significant economicalsavings can be made through investmentswith short payback time..

This work is about collaboration and staining in the upper secondary school Electrical program. How should the coloring go to in order to increase students' motivation and thus facilitate students' learning is the main subject with the work. The study has shown that there is a functional co-operation today, and that students believe that if the cooperation would increase. It would also in-crease their motivation to improve..

This master thesis is made of two parts. The first part concerns the method and results ofdesigning a motion control system for a piece of research-equipment called BIRGIT. Theequipment is made to be used for research on eyemovements. In the second part, a computermodel of a part of the balance organ in the inner-ear is developed. The work has been done atthe Bernadotte laboratory at S:t Erik Eye Hospital.The equipment the control system is made for is a so-called rotationchair.

The title Urban furniture for young people reveals that this paper handles two central phenomenon in landscape architecture; the form and content of the urban spaces, respectively the users and their need for an appropriate outdoor environment in the city. In this paper youth is referred to as 15-18 year olds and the paper is based on theories of their physical use of the city?s outdoor environment. Urban furniture refers to equipment and components in the public room which becomes furniture when people takes them in to claim and gives them a meaning and a function that is useful for the moment. The starting point is that the users, in this case youths, defi nes urban furniture as something signifi cantly more than traditional park furniture, bicycle racks and waste baskets. This paper aims to investigate how the city?s furniture can be developed to meet the youths need to see each other, move and make their marks in the public room. The theories about how youths uses the city are presented in the Theory chapter.

Detta examensarbete har utförts i samarbete med Svedala Compaction Equipment AB. Examensarbetets primära mål var att reducera höjden på ROPS tillhörande asfaltvält CC 422. En sänkning medför ett friare vägval och billigare transporter. Hittills har vägvalet påverkats av broar, viadukter och andra hinder. Med hjälp av riktlinjer från Svedala Compaction Equipment AB och Fredy Olssons modell för integrerad produktutveckling togs kriterier fram, vilka användes vid bedömning av olika lösningsförslag.

The goal of this paper is to find out how solar cells can improve energy efficiency on-board M/S Sydfart. The paper is based on a number of energy measurements on board the M/S Sydfart. The solar surface is calculated by measuring the available space for installing solar panels. Global radiation data is taken from STRÅNG's database, the data is then used to calculate the theoretical power produced by the solar cells. Energy efficiency is analysed in two ways.

Through extensive research it has shown that today?s sail boat owners are very frustrated concerning the limited choice of engine alternatives offered by today?s market. Besides rising fuel-costs, environmental awareness is very important in today?s society. Hence it is vital to find alternative environmental-friendly motors and replace combustion-engines. Zilent Ocean is an extensive project within Development engineering program at Halmstad University.

Göteborg Energi has a surplus of district heating during spring, summer and fall. The heat surplus is due to a constant production of waste heat from oil refineries and heat from waste incineration over the year. It would be desirable to increase the demand for heat and the uptime for the newly built combined heat and power generation plant, Rya Kraftvärmeverk. One alternative could be to integrate Rya Kraftvärmeverk with a pellet production facility. By producing heat, electricity and pellet in a joint process the energy use can be decreased.

Vattenfall Heat Uppsala runs the waste incineration plant in Uppsala, which produces district heating, process steam, district cooling and electricity. Vattenfall Heat Uppsala has decided to introduce an energy management system with the aim to increase the energy efficiency of the plant. The basis in such a system is to make an energy mapping.In this thesis an energy mapping has been performed at the waste incineration plant with the aim to identify and determine the size of energy flows. The investigated energy flows are used fuel, produced and used steam, produced district heating and cooling. Also the use of electricity to run the processes has been investigated.

The most common way to treat wastewater in Sweden today is by a combination of an activated sludge process and a chemical treatment. These processes are not very energy efficient and may not be the most environmentally friendly. That is why it is interesting to evaluate new alternative methods to see if they can be less harmful to the environment and help to a lower resource consumption. New techniques are tested in a pilot installation at Hammarby Sjöstad, Sjöstadsverket. To be able to evaluate these techniques in a wide perspective system analyses are conducted where different impacts can be considered, advantages and disadvantages in the systems.Five system structures for water treatment have been constructed in Matlab/Simulink in this study.

The subject of this bachelors degree project is an interior layout for road ambulances.Landstinget Västernorrland (LVN) wanted a layout concept that would be used to com- municate their design intentions to the ambulance producers during their purchase process.Designing ambulance interiors is an extremely complex process since there so many fac- tors to take into consideration. It ?s not just about taking the equipment and place it where there is space left in the cabin. You have to start with the user in focus and the tasks that are to be performed in the ambulance environment.It ishard to find design solutions that will fit 100% of the ambulance personnel?s working routines for 100% of the tasks.

This degree project has been carried out in cooperation with Gedevelop in Helsingborg.Gedevelop has developed a camera that can calculate the weight of a liquid glass mass.Because of the density and viscosity changes in the glass, the weight information issometimes incorrect given. Glass industry is today addressing the problem by an operatorperforming a manual weighing of a few bottles which, in turn, calibrates the camera system.The project aimed to develop an automated system to control the weighing of glass bottles forglass industries. This system must be so flexible that it can be easily mounted on plants withdifferent production equipment around the world.The project includes design and construction of equipment that meets the requirementsformulated together with Gedevelop. Work has been done both in Halmstad and Helsingborgand has included both calculations and review of the theory to understand the forces thatinfluence the design of different construction parts. A prototype was produced that meets theoperating requirements for the design and can be used in testing features.

The moisture content in 10 deliveries of tree parts and 10 deliveries of wood residues were measured with different methods to analyze the quality of procedure used at Dåvamyran today. At the same time a survey was made on the measure procedures used at heating plants in Sweden The majority of the heating plants in Sweden use weight and moisture content as base for payment but at some plants only volume. The moisture content is usually estimated by drying wood chips in an oven but few plants a visual estimation is used. At few plants moisture content is estimated spectroscopicily. The techniques using near infra read light and other electromagnetic are still at a test stage. The methods of measurement used today are quit unreliable for the individual deliveries and there is a risk for systematic mistakes.

Detta examensarbete har utförts i samarbete med Svedala Compaction Equipment AB. Examensarbetets primära mål var att reducera höjden på ROPS tillhörande asfaltvält CC 422. En sänkning medför ett friare vägval och billigare transporter. Hittills har vägvalet påverkats av broar, viadukter och andra hinder. Med hjälp av riktlinjer från Svedala Compaction Equipment AB och Fredy Olssons modell för integrerad produktutveckling togs kriterier fram, vilka användes vid bedömning av olika lösningsförslag. Utvärderingen resulterade i att två av de tio ursprungliga förslagen gick vidare till nästa steg i produktutvecklingsprocessen - primärkonstruktion. Primärkonstruktionen inleddes med vidareutveckling av de två principförslagen.

The goal of this paper is to find out how solar cells can improve energy efficiency on-board M/S Sydfart. The paper is based on a number of energy measurements on board the M/S Sydfart. The solar surface is calculated by measuring the available space for installing solar panels. Global radiation data is taken from STRÅNG's database, the data is then used to calculate the theoretical power produced by the solar cells. Energy efficiency is analysed in two ways.